Vemmio DS-100 User manual

1
DS-100 double switch
Fig 1. Assembling
This in-wall dual relay switch module is a transceiver which is a Z-Wave Plus
TM
enabled device and is fully compatible with any Z-Wave
TM
enabled network.
Z-Wave Plus
TM
enabled devices displaying the Z-Wave Plus
TM
logo can also be
used with it regardless of the manufacturer, and can also be used in other
manufacturer’s Z-Wave
TM
enabled networks. Mini size design let the module
can easily hide itself into the wall box and that will be good for the house
decoration.
There are many kind of application by using the module to switch AC power On
and Off, one main application is the light control. The new smart relay calibration
technology can reduce the inrush current caused by the load and let the module
work perfectly with many kind of light like incandescent, fluorescent and LED
light.
This in-wall switch module is able to detect Instant power wattage and overload
current (7.5A with resistive load) of connected light or appliances. When
detecting overload state, the Module will be disabled and its On/Off button will
be lockout of which LED will flash quickly. However, disconnect and re-connect
the Module will reset its overload condition to normal status.
Adding to Z-Wave
TM
Network
In the front casing, there is an on/off button with LED indicator below which is
used to toggle switch on and off or carry out inclusion, exclusion, reset or
association. When first power is applied, its LED flashes on and off alternately
and repeatedly at 0.5 second intervals. It implies that it has not been assigned a
node ID and start auto inclusion.
Auto Inclusion
The function of auto inclusion will be executed as long as the in wall switch does
not have Node ID and just connect the switch to main power.
Note: Auto inclusion timeout is 2 minute during which the node information of
explorer frame will be emitted once every several seconds. Unlike “inclusion”
function as shown in the table below, the execution of auto inclusion is free from
pressing the On/Off button on the Switch.
The table below lists an operation summary of basic Z-Wave functions. Please
refer to the instructions for your Z-Wave
TM
Certificated Primary Controller to

2
access the Setup function, and to include/exclude/associate devices
Function Description
Annotation
No node ID The Z-Wave Controller does not allocate
a node ID to the Switch. LED 2-second on, 2-second off
Add (Inclusion) 1. Put your Z-Wave controller into
inclusion mode by following the
instructions provided by the
controller manufacturer.
One press one flash LED
2. Pressing INCLUDE_BUTTON three
times within 2 seconds will enter
inclusion mode.
Remove
(Exclusion) 1. Put your Z-Wave controller into
exclusion mode by following the
instructions provided by the
controller manufacturer.
One press one flash LED
1. Pressing INCLUDE_BUTTON three
times within 2 seconds will enter
exclusion mode.
3. Node ID has been excluded. LED 0.5s On, 0.5s Off
(Enter auto inclusion)
Reset 1. Pressing INCLUDE_BUTTON three
times within 2 seconds will enter
inclusion mode.
Use this procedure only in
the event that the primary
controller is lost or
otherwise inoperable.
2. Within 1 second, press On/Off
button again for 5 seconds.
3. IDs are excluded. LED 0.5s On, 0.5s Off
(Enter auto inclusion)
Association 1. The DS-100 is an always listening
Z-Wave device, so associations
be added or removed by a controller
at any time.
Or If your controller requires to have
the DS-100 send a 'node
information frame' or NIF for
associations, pressing the On/Off
button three times within 2 seconds
will cause the DS-100 to send its
NIF.
LED one press one flash
2. There are 3 groups for the switch

Adding a node ID allocated by Z-Wave Controller means inclusion. Removing a node
ID allocated by Z-Wave Controller means exclusion.
 Failed or success in including/excluding the node ID can be viewed from the Z-Wave
Controller.
Sometimes people are not easy to execute exclusion or inclusion especially
when DS-100 already installed in a wall box. To solve this issue, DS-100
support a special feature that can use S1 or S2 to execute “exclusion, inclusion,
Reset or Association” at the first 3 minutes when first time connect to main
power.
LED Indication
To distinguish what mode the switch is in, view from the LED for identification.
State Type LED Indication
Normal Whatever we switch On and off of the DS-100 by S1 S2 or On/Off
button or RF command, the LED will lights up 1 second and then
off.
No node ID Under normal operation, when the Switch has not been allocated a
node ID, the LED flashes on and off alternately at 2-second
intervals. By pressing S1 S2 or On/Off button, it will stop flashing
temporarily.
Learning When DS-100 is in learning mode, LED flashes on and off
alternately and repeatedly at 0.5 second intervals.
Overload When overload state occurs, the Switch is disabled of which LED
flashes on and off alternately at 0.2 second intervals. Overload
state can be cleared by disconnect and reconnect the Switch to
the main power
Choosing a Suitable Location
1. Do not locate the Switch facing direct sunlight, humid or dusty place.
2. The suitable ambient temperature for the Switch is 0°C~40°C.
3. Do not locate the Switch where exists combustible substances or any
source of heat, e.g. fires, radiators, boiler etc.
4. After putting it into use, the body of Switch will become a little bit hot of
which phenomenon is normal.

3
Installation
1. Put the in wall switch into a wall box and connect the AC power wire L,N to
DS-100 connector L, N.
2. Connect the wall switch to the DS-100 as Fig1 .
3. To manually turn ON the Switch, press and release the On/Off button. The
LED will light ON for 1 second, and the load plugged into the Switch will
also turn ON.
4. To manually turn OFF the Switch, simply press and release the On/Off
button. The LED will light ON for 1 second and the load plugged into the
Switch will turn OFF.
Programming
1. Basic Command Class / Binary Switch Command Class
The Switch will respond to BASIC and BINARY SWITCH commands that
are part of the Z-Wave system.
1-1 BASIC_GET / BINARY_SWITCH_GET
Since the switch have two relay, the Switch will report its On/Off state to
the Controller by setting Configuration parameter 3.
Configuration parameter 3=1 Report ON when relay 1 ON
Report OFF when relay 1 OFF
Configuration parameter 3=2 Report ON when relay 2 ON
Report OFF when relay 2 OFF
Configuration parameter 3=3 (default)
Report ON when either relay 1 ON or relay 2 ON
Report OFF when both relay 1 and relay 2 OFF
Basic Get Command: [Command Class Basic, Basic Get]
Basic Report Command:
Report OFF: [Command Class Basic, Basic Report, Value = 0(0x00)]
Report ON:[Command Class Basic, Basic Report, Value = 255(0xFF)]
Binary Switch Get Command:[Command Class Switch Binary, Switch
Binary Get]
Binary Switch Report Command:
Report OFF:[Command Class Switch Binary, Switch Binary Report,
Value =0(0x00)]
Report ON:[Command Class Switch Binary, Switch Binary Report, Value
= 255(0xFF)]
1-2 BASIC_SET / SWITCH_BINARY_SET
Since the switch has two relay, the load attached to the Switch will turn on
or off upon receipt of the following commands from a Z-Wave Controller by
setting Configuration parameter 3.
Configuration parameter 3=1 switch ON and OFF of relay 1
Configuration parameter 3=2 switch ON and OFF of relay 2
Configuration parameter 3=3(default)
switch ON and OFF both relay 1 and relay 2
[Command Class Basic, Basic Set, Value = 1~99, 255(0xFF)]: the load
attached to the Switch turns on.

4
[Command Class Basic, Basic Set, Value = 0(0x00)]: the load attached to
the Switch turns off.
[Command Class Switch Binary, Switch Binary Set, Value = 1~99,
255(0xFF)]: the load attached to the Switch turns on.
[Command Class Switch Binary, Switch Binary Set, Value = 0(0x00)]: the
load attached to the Switch turns off.
1. Z-Wave’s Groups (Association Command Class Version 2)
The Switch can be set to send reports to control associated Z-Wave devices. It
supports 3 association groups which every group has one node support.
Group1~Group3 support SWITCH_BINARY_REPORT,
METER_REPORT_COMMAND_V3
For group 1, the Switch will report (1) ON/OFF status of Relay1 and Relay2 (2)
Instant Power Consumption (Watt) of Relay1 and Relay2 (3) Accumulated
Power Consumption (KWh) of Relay1 and Relay2 to Z-Wave Controller.
For group 2, the Switch will report (1) ON/OFF status of Relay1 (2) Instant
Power Consumption (Watt) of Relay1 (3) Accumulated Power Consumption
(KWh) of Relay1 to Z-Wave Controller.
For group 3, the Switch will report (1) ON/OFF status of Relay2 (2) Instant
Power Consumption (Watt) of Relay2 (3) Accumulated Power Consumption
(KWh) of Relay2 to Z-Wave Controller.
2-1 Auto report to Grouping 1 ~3(Maximum Node 1)
2-1-1 On/Off Event Report
When “on” or “off” state has been changed, it will send Binary Switch Report
to the nodes of Group1~3.
Binary Switch Report
ON:[Command Class Switch Binary, Switch Binary Report, Value
=255(0xFF)]
OFF:[Command Class Switch Binary, Switch Binary Report, Value
=0(0x00)]
2-1-2 Instant Power Consumption vary over 5% report
When the power consumption of load vary over 5%, it will send Meter report
to the nodes of Group
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =
0x01，Precision = 1，Scale = 0x02，Size = 4，Meter Value(W) ]
2-1-3 overload alarm report command
When DS-100 detect the overload, it will send Alarm Report to the correspond
Group。
The content of Alarm Report
Alarm report command: [Command_Class_Alarm, Alarm_Report, Alarm Type =
[Command_Class_Alarm, Alarm_Report, Alarm Type = [Command_Class_Alarm, Alarm_Report, Alarm Type =
[Command_Class_Alarm, Alarm_Report, Alarm Type =
0x08,
0x08, 0x08,
0x08, Alarm Level =
Alarm Level =Alarm Level =
Alarm Level = 0xFF]
0xFF]0xFF]
0xFF]
2-2 Response to Meter Get Command
The Switch will report its (1) instant Power Consumption (Watt) or (2)
accumulated power consumption(KWH) or (3) AC load Voltage (V) or (4) AC
load current ( I ) (5) load power factor (PF) to Z-Wave Controller after
receive the Meter Get Command from Z-Wave Controller.
2-2-1 Instant Power Consumption (Watt) of Switch
When receiving Meter Get Command, it will report Meter Report Command
to the node asked.
Meter Get Command: [Command Class Meter, Meter Get, Scale
=0x02(W)]
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =
0x01，Precision = 1，Scale = 0x02，Size = 4，Meter Value(W) ]
Example:

5
Meter Value 1 = 0x00 (W)
Meter Value 2 = 0x00 (W)
Meter Value 3 = 0x03 (W)
Meter Value 4 = 0xEA (W)
Meter(W) = Meter Value 3 *256 + Meter Value 4 = 100.2W
2-2-2 Accumulated Power Consumption (KW/h)
When receiving Meter Get Command, it will report Meter Report
Command to the node asked.
Meter Get Command:
[Command Class Meter, Meter Get, Scale = 0x00 KW/h)]
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01， Meter Type
=0x01， Precision = 2，Scale = 0x00，Size = 4，Meter Value (KWh)]
Example:
Scale = 0x00 (KWh)
Precision = 2
Size = 4 Bytes (KW/h)
Meter Value 1 = 0x00(KWh)
Meter Value 2 = 0x01(KWh)
Meter Value 3 = 0x38(KWh)
Meter Value 4 = 0xA3(KWh)
Accumulated power consumption (KW/h) = (Meter Value 2*65536) +
(Meter Value 3*256) + (Meter Value 4) = 800.35 (KW/h)
2-2-3 Clearing accumulated power consumption
Whenever re-start counting the accumulated power consumption is needed,
you can use Meter Reset Command to clear it.
Meter Reset Command: [Command Class Meter, Meter Reset]
2-2-4 AC load Voltage (V)
When receiving Meter Get Command, it will report Meter Report Command
to the node asked.
Meter Get Command: [Command Class Meter, Meter Get, Scale =0x04(V)]
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =
0x01，Precision = 1，Scale = 0x04，Size = 2， Meter Value(V)]
Example:
Scale = 0x04 (V)
Precision = 1
Size = 2 (2 Bytes of V)
Meter Value 1 = 0x09(V)
Meter Value 2 = 0x01(V)
AC load Voltage = (Meter Value 1*256) +(Meter Value 2)= 230.5 (V)
2-2-5 AC load current ( I )
When receiving Meter Get Command, it will report Meter Report Command to
the node asked.
Meter Get Command: [Command Class Meter, Meter Get, Scale =0x05(I)]
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type
= 0x01，Precision = 2，Scale = 0x05，Size = 2，Meter Value(I)]
Example:
Scale = 0x05 (I)
Precision = 2
Size = 2 (2 Bytes of I)
Meter Value 1 = 0x01(I)
Meter Value 2 = 0x21(I)
AC load current = (Meter Value 1*256) +(Meter Value 2)= 2.89 (A)
2-2-6 load power factor (PF)
When receiving Meter Get Command, it will report Meter Report Command to

6
the node asked.
Meter Get Command: [Command Class Meter, Meter Get, Scale =0x06(PF)]
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =
0x01， Precision = 2，Scale = 0x06，Size = 1 Bytes，Meter Value(PF)]
Example:
Scale = 0x06 (PF)
Precision = 2
Size = 1 (1 Byte of PF)
Meter Value 1 = 0x63(PF) (It means that the load power factor is 0.99)
2-3 Multi Channel Command Class Version 3
DS-100 also support Muti Channel command class (version 3), which include
BINARY_SWITCH_GET, BINARY_SWITCH_SET, BASIC_GET, BASIC_SET,
METER_SUPPORTED_GET, METER_RESET, METER_GET
You may control or get report from 3 endpoints of DS-100
2-3-1 BINARY_SWITCH_GET,
You may get the ON/OFF state from every endpoint, when endpoint set to 1,
DS-100 will reply state of Relay1. If endpoint set to 2, DS-100 will reply state of
Relay2. If endpoint set to 3, DS-100 will reply ON (0xFF) when either Relay 1
or Relay2 is ON, report OFF (0x00) when both Relay 1 and Relay2 are OFF.
Below is an example show a source endpoint 5 send a Get command to
DS-100 endpoint 3.
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x05 (this is the endpoint of command
inquirer here we assume endpoint
is 5, if the inquirer doesn’t support
multi Channel this value will be 0)
(Bit Address+Destination End Point = 0x03)
(Bit Address =0；Destination End Point
range from 1~3)
Command Class = 0x25 (Command_Class_Switch_Binary =
0x25)
Command =0x02 (Switch_Binary_Get = 0x02)
Below is the example show DS-100 report to last command
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x03 Since the endpoint is 3 so DS-100 will
reply ON(0xFF) when either Relay 1 or
Relay2 is ON, report OFF (0x00) when
both Relay 1 and Relay2 are OFF
(Bit Address+Destination End Point = 0x05)
(Bit Address =0；Destination End Point)
Command Class = 0x25 (Command_Class_Switch_Binary =

7
0x25)
Command =0x03 (Switch_Binary_Report = 0x3)
Parameter 1 = 0xFF (ON=0xFF ，OFF=0x00)
2-3-2 BINARY_SWITCH_SET
By using BINARY_SWITCH_SET Command of Multi Channel Command Class
Encapsulation Command, you can switch Relay1 ON/OFF by setting endpoint to
1, or switch Relay2 ON/OFF by setting endpoint to 2, or switch both Relay1 and
Relay2 ON/OFF by setting endpoint to 3
The example of the command show that switch off relay1 of DS-100
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x01 (this is the endpoint of command
inquirer here we assume endpoint is
1，if the inquirer doesn’t support multi
Channel this value will be 0)
(Bit Address+Destination End Point = 0x01)
(Bit Address =0；Destination End Point
range1~3)
Command Class = 0x25 (Command_Class_Switch_Binary =
0x25)
Command =0x01 (Switch_Binary_Set = 0x01)
Parameter 1 = 0x00 (ON=0xFF ，OFF=0x00)
2-3-3 METER_SUPPORTED_GET：
：：
：
This command is to ask the endpoint of DS-100 what kind of meter data can
be
reported
The example show how to get the meter report type
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x01 (this is the endpoint of command
inquirer here we assume endpoint is
1，if the inquirer doesn’t support multi
Channel this value will be 0)
(Bit Address+Destination End Point = 0x03)
(Bit Address =0；Destination End Point
range1~3)
Command Class = 0x32 ( Command_Class_Meter_V3 = 0x32)
Command =0x03 (Meter_Supported_Get = 0x03)
Below is the example show DS-100 report to last command

8
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x03
(Bit Address+Destination End Point = 0x01)
Command Class = 0x32 (Command_Class_Meter_V3 = 0x32)
Command =0x04 (Meter_Supported_Report = 0x04)
Parameter 1 = 0x81 (Meter Reset =1, Meter Type=0x01)
Parameter 2 = 0x75 (Scale Supported =
KWh+W+V+A+Power Factor = 0x75)
2-3-4 METER_RESET
This command is to reset the Accumulated Power Consumption (KWh) to 0
The example show how to reset the KWh
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x03 (this is the endpoint of command
inquirer, here we assume endpoint is
3，if the inquirer doesn’t support multi
Channel this value will be 0)
(Bit Address+Destination End Point = 0x01)
(Bit Address =0；Destination End Point
range1~3)
Command Class = 0x32 ( Command_Class_Meter_V3 = 0x32)
Command =0x05 ( Meter_Reset = 0x05)
2-3-5 METER_GET：
：：
：
Using meter get command to get the KWH, W, V, I, PF from endpoint of DS-100
2-3-5-1 Get KWH from endpoint
Meter_GET example:
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x05 (this is the endpoint of command
inquirer, here we assume endpoint is
5，if the inquirer doesn’t support multi
Channel this value will be 0)
(Bit Address+Destination End Point = 0x03)
(Bit Address =0；Destination End Point
range1~3)
Command Class = 0x32 ( Command_Class_Meter_V3 = 0x32)
Command =0x01 (Meter_Get = 0x01)
Parameter 1 = 0x00 (Scale = KWH = 0x00)
Accumulated power consumption (KWH) Report example：
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP

9
Source End Point = 0x03 (Meter report = Endpoint3)
(Bit Address+Destination End Point = 0x05)
(Bit Address =0；
Destination End Point =
command inquirer’s Endpoint value)
Command Class = 0x32 (Command_Class_Meter_V3 = 0x32)
Command =0x02 (Meter_Report = 0x02)
Parameter 1 = 0x21 (Scale Bit2 = 0 ，Rate Type = 0x01，
Meter Type=0x01)
Parameter 2 = 0x44 (Precision = 2，Scale Bit1Bit0 = 0，
Size
= 4)
Parameter 3 = 0x00 Accumulated Power Consumption =
0x000005FD = 15.33 KWh
Parameter 4 = 0x00
Parameter 5 = 0x05
Parameter 6 = 0xFD
2-3-5-2 Get Instant Power Consumption (Watt) from endpoint
METER_GET example：
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x05 (this is the endpoint of command inquirer,
here we assume endpoint is 5，if the
inquirer doesn’t support multi Channel this
value will be 0)
(Bit Address+Destination End Point =
0x03)
(Bit Address =0；Destination End Point
range 1~3)
Command Class = 0x32 ( Command_Class_Meter_V3 = 0x32)
Command =0x01 (Meter_Get = 0x01)
Parameter 1 = 0x10 (Scale = W = 0x02)
DS-100 Instant Power Consumption (W) Report example：
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x03 (Meter report = Endpoint3)
(Bit Address+Destination End Point = 0x05)
(Bit Address =0；
Destination End Point =
command inquirer’s Endpoint value)
Command Class = 0x32 (Command_Class_Meter_V3 = 0x32)
Command =0x02 (Meter_Report = 0x02)
Parameter 1 = 0x21 (Scale Bit2 = 0, Rate Type = 0x01，
Meter Type=0x01)
Parameter 2 = 0x34 (Precision = 1，Scale Bit1Bit0 = 0x02，
Size = 4)

10
Parameter 3 = 0x00 Instant Power Consumption =
0x000003EA
= 100.2W
Parameter 4 = 0x00
Parameter 5 = 0x03
Parameter 6 = 0xEA
2-3-5-3 Get load voltage V from endpoint
Meter_GET example:
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x05 (this is the endpoint of command inquirer,
here we assume endpoint is 5，if the
inquirer doesn’t support multi Channel this
value will be 0)
(Bit Address+Destination End Point =
0x03)
(Bit Address =0；Destination End Point
range1~3)
Command Class = 0x32 ( Command_Class_Meter_V3 = 0x32)
Command =0x01 (Meter_Get = 0x01)
Parameter 1 = 0x20 (Scale = V = 0x04)
DS-100 AC load Voltage report example：
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x03 (Meter report = Endpoint3)
(Bit Address+Destination End Point = 0x05)
(Bit Address =0；
Destination End Point =
command inquirer’s Endpoint value)
Command Class = 0x32 (Command_Class_Meter_V3 = 0x32)
Command =0x02 (Meter_Report = 0x02)
Parameter 1 = 0xA1 (Scale Bit2 = 1, Rate Type = 0x01,
Meter Type=0x01)
Parameter 2 = 0x22 (Precision = 1, Scale Bit1Bit0 = 0x00,
Size = 2)
Parameter 3 = 0x09 Voltage = 0x0910 = 232.0V
Parameter 4 = 0x10
2-3-5-4 Get load current I from endpoint
Meter_GET example:
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x05 (this is the endpoint of command inquirer,
here we assume endpoint is 5，if the
inquirer doesn’t support multi Channel this

11
value will be 0)
(Bit Address+Destination End Point =
0x03)
(Bit Address =0；Destination End Point
range1~3)
Command Class = 0x32 ( Command_Class_Meter_V3 = 0x32)
Command =0x01 (Meter_Get = 0x01)
Parameter 1 = 0x28 (Scale = A = 0x05)
DS-100 AC load current (I) example：
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x03 (Meter report = Endpoint3)
(Bit Address+Destination End Point = 0x05)
(Bit Address =0；
Destination End Point =
command inquirer’s Endpoint value)
Command Class = 0x32 (Command_Class_Meter_V3 = 0x32)
Command =0x02 (Meter_Report = 0x02)
Parameter 1 = 0xA1 (Scale Bit2 = 1, Rate Type = 0x01,
Meter Type=0x01)
Parameter 2 = 0x4A (Precision = 2, Scale Bit1Bit0 = 0x01,
Size = 2)
Parameter 3 = 0x00 Current = 0x002B = 0.43A
Parameter 4 = 0x2B
2-3-5-5 Get power factor PF from endpoint
Meter_GET example:
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP
Source End Point = 0x05 (this is the endpoint of command inquirer,
here we assume endpoint is 5，if the
inquirer doesn’t support multi Channel this
value will be 0)
(Bit Address+Destination End Point =
0x03)
(Bit Address =0；Destination End Point
range1~3)
Command Class = 0x32 ( Command_Class_Meter_V3 = 0x32)
Command =0x01 (Meter_Get = 0x01)
Parameter 1 = 0x30 (Scale = PF = 0x06)
DS-100 power factor report example：
COMMAND_CLASS_MULTI_CHANNEL
MULTI_CHANNEL_CMD_ENCAP

12
Source End Point = 0x03 (Meter report = Endpoint3)
(Bit Address+Destination End Point =
0x05)
(Bit Address =0；Destination End Point =
command inquirer’s Endpoint value)
Command Class = 0x32 (Command_Class_Meter_V3 = 0x32)
Command =0x02 (Meter_Report = 0x02)
Parameter 1 = 0xA1 (Scale Bit2 = 1, Rate Type = 0x01,
Meter Type=0x01)
Parameter 2 = 0x51 (Precision = 2, Scale Bit1Bit0 = 0x10, Size
= 1)
Parameter 3 = 0x63 Power Factor = 0x63 = 0.99
2. Z-Wave’s Configuration
Configuration
Parameter Function Size (Byte) Value Unit Default
Description
1 Watt Meter
Report
Period
2 0x01-
0x7FFF 5s 720 720*5s=3600s=1 hour
2 KWH
Meter
Report
Period
2 0x01-
0x7FFF 10min
6 6*10min= 1 hour
3 Selected
Relay
1 1-3 3 1：Relay1
2：Relay2
3：Relay1 &
Relay2
4 Edge or
Pulse
mode or
1 1-3 1 1：Edge mode
2：Pulse mode
Edge-Toggl
e mode
3：Edge-
Toggle
mode
5 Threshold
of current
for Load
Caution
2 10-750 0.01A 750
750*0.01A = 7.5A
6 Threshold
of KWH for
Load
Caution
2 1-10000 1KWh 10000
7 Restore
switch
state mode
1 0-2 1 0 : Switch off
1 : Last switch
state
2 : Switch on
8 Auto off
timer 2
0
-
0x7FFF
1s 0 0 : Disable auto
off function
1-0x7FFF : 1s ~
32767s
9 RF off
command
mode
1 0-3 0 0 : Switch off
1 : Ignore
2 : Switch toggle
3 : Switch on
10 Existence
of
Endpoint3
1 1-2 1 1 : Endpoint3 exist
2 : No Endpoint3
3-1 Watt Meter Report Period:
If the setting is configured for 1hour (set value =720), the DS-100 will report
its instant power consumption every 1 hour to the node of correspond Group.
The maximum interval to report its instant power consumption is 45 hours
(5s*32767/3600=45hr).
3-2 KWH Meter Report Period:
If the setting is configured for 1hour (set value =6), the DS-100 will report its
Accumulated Power Consumption (KW/h) every 1 hour to the node of
correspond Group. The maximum interval to report its Accumulated Power
Consumption (KW/h) is 227.55 days (10min*32767/1440=227.55 days).
3-3 Selected Relay
If Controller not using Multi_Channel command class to access the relay of
DS-100, you may configure the select value to react the Basic Command
Class、Binary Switch Command Class or Meter Command Class V3

13
3-3-1 Selected Relay1:
Only relay1 can be controlled and report.
3-3-2 Selected Relay 2:
Only relay2 can be controlled and report.
3-3-3 Selected Relay1 and Relay2：
：：
：Default select is 3
Both relay1 and relay2 can be controlled and report.
Set command Relay state
Basic_Set or Binary_Switch_Set ON Both Relay1 and Relay2 ON.
Basic_Set or Binary_Switch_Set OFF Both Relay1 and Relay2 OFF.
Get command Relay state Report to command sender
Basic_Get or Binary_Switch_Get Either relay1 ON
or relay2 ON
ON
Basic_Get or Binary_Switch_Get Both relay1 OFF
and relay2
OFF
OFF
Get command parameter Report to command sender
Meter_Get KWh Relay1 KWh1+Relay2 KWh2
Meter_Get
Watt Relay1 W1+Relay2 W2
Meter_Get
Voltage Relay1 and Relay2 are the same
voltage
Meter_Get
Current Relay1 I1+Relay2 I2
Meter_Get Power factor PF Relay1
3-4 Edge and Pulse mode
Manual switch S1 and S2 can set to Edge mode or Pulse mode or Edge-Toggle
mode, default value is Edge mode.
3-4-1 Edge mode: this mode is suitable for the bi stable wall switch that has
indicator point on the switch, and the same position correspond to same
state of relay1 and relay2. if the DS-100 relay change the state because of
receiving Z-Wave RF command, it may need two times of change (switch on
to off or switch off to on) to let relay back to the correspond state.
3-4-2 Pulse mode: this mode is suitable for the toggle type wall switch to swap
the state of Relay1 or Relay2.
3-4-3 Edge-Toggle mode: this mode is suitable for the normal bi-stable switch,
every time when change the state of the wall switch will also swap the state
of Relay1 or Relay2.
3-5 Threshold of current for Load Caution
This is a warning when the current of load over the preset threshold value, if the
setting value is 750, when the load current of Relay1 or Relay2 over this value,
DS-100 will send current meter report to the node of correspond Group, the
Range of the setting value is from 10 to 750, and the default value is 750.
3-6 Threshold of KWh for Load Caution
This is a warning when the KWh of load over the preset threshold value, If the
setting value is 10000, when the Accumulated Power Consumption of Relay1 or
Relay2 over this value, DS-100 will send KWh Meter Report command to the
node of correspond Group, minimum value is 1KWh and default value is 10000
kWh.
3-7 Restore switch state mode

14
Whenever the AC power return from lost, DS-100 will restore the switch state
which could be SWITCH OFF、LAST SWITCH STATE、SWITCH ON. The default
setting is LAST SWITCH STATE.
3-8 Auto off timer：
：：
：
Whenever PAN11 switches to on, the auto off timer begin to count down. After
the timer decrease to zero, it will switch off automatically. However if Auto off
timer is set as 0, the auto off function will be disabled. The default setting is 0.
3-9 RF off command mode
Whenever a switch off command, BASIC_SET 、BINARY_SWITCH_SET 、
SWITCH_ALL_OFF, is received, it could be interpreted as 4 kinds of
commands.
3-9-1 Switch Off：It switches to OFF state. The default setting is Switch Off.
3-9-2 Ignore：The switch off command will be ignored.
3-9-3 Switch Toggle：It switches to the inverse of current state.
3-9-4 Switch On：It switches to ON state.
3-10 Existence of Endpoint3：
：：
：
Multi-Channel Command is a good way to control relay1 and relay2 of DS-100
individually. The endpoint3 of DS-100 is related to both relay1 and relay2. In
some condition it becomes redundant in Multi-Channel Command Class. When
the Existence of Endpoint3 is set as 2, the endpoint3 will be disabled. The
default value is 1.
Endpoint1 and Endpoint2 are fixed, only Endpoint3 is dynamic.
4. Protection Command Classes
DS-100 supports Protection Command Class version 2, it can protect the switch
against unintentionally control by e.g. a child. And it can also protect the switch
from being turned off by setting it in “No RF Control” state.
After being set to “Protection by sequence” state, any intentional pressing of
On/Off button or S2/S2 should be hold longer than 1 second, or the switch state
will not change. However, the operation of learn function does not change,
because learning will not be protected.
5. Firmware update over the air (OTA)
DS-100 is based on 500 series SoC and supports Firmware Update Command
Class, it can receives the updated firmware image sent by controller via the
Z-wave RF media. It is a helpful and convenient way to improve some function if
needed.
6. Command Classes
The Switch supports Command Classes including…
* COMMAND_CLASS_ZWAVEPLUS_INFO
* COMMAND_CLASS_VERSION_V2
* COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
* COMMAND_CLASS_DEVICE_RESET_LOCALLY
* COMMAND_CLASS_ASSOCIATION_V2
* COMMAND_CLASS_ASSOCIATION_GRP_INFO
* COMMAND_CLASS_POWERLEVEL
* COMMAND_CLASS_SWITCH_BINARY
* COMMAND_CLASS_BASIC
* COMMAND_CLASS_SWITCH_ALL
* COMMAND_CLASS_ALARM
* COMMAND_CLASS_SCENE_ACTIVATION
* COMMAND_CLASS_SCENE_ACTUATOR_CONF
* COMMAND_CLASS_PROTECTION
* COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
* COMMAND_CLASS_MULTI_CHANNEL_V3
* COMMAND_CLASS_METER_V3
* COMMAND_CLASS_CONFIGURATION
Troubleshooting

15
Symptom
Cause of Failure
Recommendation
The Switch not working and
LED off 1. The Switch is not connect to the Main
power
2. The Switch break
down
1. Check power connections
2. Don’t open up the Switch and
send it for repair.
The Switch LED
illuminating, but cannot
control the ON/OFF
Switch of the load attached
Check if the load connect
into the Switch has its
own ON/OFF switch
Set the ON/OFF switch of the load
attached to ON
The Switch LED
illuminating, but the
Detector cannot control
the Switch
1. Not carry out
association
2. Same frequency
interference
1. Carry out association
2. Wait for a while to re-try
LED keep flashing, but
cannot control Overload occurs Remove the load attached or check max. load cannot exceed
7.5A(Resistive load)
Specification
Operating Voltage 100 ~240VAC
Maximum Load 6.5A(230Vac/120Vac) (Resistive load)
Range Minimum 30 m in door 100m outdoor line of sight
Operating Temperature 0°C ~ 40°C
Frequency Range DS-100-1: 868.40MHz; 869.85MHz(EU) /
DS-100-2: 908.40MHz; 916.00MHz(USA/Canada) /
DS-100-3: 922.5MHz/ 923.9MHz/ 926.3MHz (Taiwan/JP)
** Specifications are subject to change and improvement without notice.
Warning:
1. Plug out to disconnect from power supply; Do not plug in line.
2. Do not exceed the max rating
Disposal
This marking indicates that this product should not be disposed with
other household wastes throu
ghout the EU. To prevent possible harm to
the environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and
collection systems or contact the retailer where the product was
purchased. They can take this product for environmental safe recycling.
Company of License Holder：Philio Technology Corporation
Address of License Holder：8F.,No.653-2,Zhongzheng Rd., Xinzhuang Dist.,
New Taipei City 24257,Taiwan(R.O.C)
FCC Interference Statement
FCC Interference StatementFCC Interference Statement
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC ules.
These limits are designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
• eorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

16
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC ules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.