VENSYS POS 4691 User manual

POS 4000
with B49 / B69 / B79
M/B Installation Guide
482000C1
Nov. 2004 V2.0

/37
2
Safety
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions carefully.Save these instructions for future reference.
2. Follow all warnings and instructions marked on the product.
3. Do not use this product near water.
4. Do not place this product on an unstable cart, stand, or table.The product may fall,
causing serious damage to the product.
5. Slots and openings in the cabinet and the back or bottom are provided for ventilation;
to ensure reliable operation of the product and to protect it from overheating, these
openings must not be blocked or covered.The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface.This product should
never be placed near or over a radiator or heat register, or in a built-in installation
unless proper ventilation is provided.
6. This product should be operated from the type of power indicated on the marking
label.If you are not sure of the type of power available,consult your dealer or local
power company.
7. Do not allow anything to rest on the power cord.Do not locate this product where
persons will walk on the cord.
8. Never push objects of any kind into this product through cabinet slots as they may
touch dangerous voltage points or short out parts that could result in a fire or electric
shock.Never spill liquid of any kind on the product.
FCC
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
CD-ROM Safety Warning
DANGER
INVISIBLE RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM
Caution on Lithium Batteries
Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer. Discard used batteries according to
the manufacturer’s instructions.

/37
3
Index
1. Accessory ...................................................................................................4
2. I/O Function................................................................................................5
2.1 POS 4000 Front View............................................................................5
2.2 POS 4000 Rear View.............................................................................6
3. Specification ...............................................................................................7
3.1 B69 & B79 .............................................................................................7
3.2 B49........................................................................................................9
3.3 System Memory Combination..............................................................11
4. Jumper Setting..........................................................................................12
4.1 B69 M/B...............................................................................................12
4.2 B79 M/B...............................................................................................14
4.4 POS I/O Board Jumper Setting............................................................18
5. Driver Installation......................................................................................19
5.1 B69 M/B...............................................................................................19
5.2 B79 M/B...............................................................................................23
5.3 B49 M/B...............................................................................................27
6.Installation the Cable Cover.......................................................................33
7. Installation Cash Drawer...........................................................................35
7.1 Cash Drawer Pin Assignment..............................................................35
7.2 Cash Drawer Controller register..........................................................35
7.3 Cash Drawer control command example.............................................36
8. Notices......................................................................................................37
8.1 Maximum dimension of Interface card.................................................37
8.2 Vertical position of POS 4000..............................................................37

/37
4
1. Accessory
a. Warranty Card b. Power Cable
c. Drivers Bank
d. Installation Guide
The following drivers in the folders of Driver Bank are necessary for driver installation.
B69 Mainboard Folder/File File Description
<CD>:\B69\B69.htm B69 Driver list
<CD>:\Common\Ac97_codec\ADI\AD1881A Audio driver
<CD>:\Common\LAN_driver\R8139_810x LAN driver
<CD>:\Common\INTEL\Chipset Chipset driver
<CD>:\Common\INTEL\i815VGA VGA driver
B79 Mainboard Folder/File File Description
<CD>:\B79\B79.htm B79 Driver list
<CD>:\Common\Ac97_codec\ADI\AD1881A Audio driver
<CD>:\Common\LAN_driver\R8139_810x LAN driver
<CD>:\Common\INTEL\Chipset Chipset driver
<CD>:\Common\INTEL\i845VGA VGA driver
<CD>:\Common\INTEL\USB20 USB2.0 driver
B49 Mainboard Folder/File File Description
<CD>:\B49\B49.htm B49 Driver list
<CD>:\Common\VIA\Chipset Chipset driver
<CD>:\Common\VIA\VGA\CLE266 VGA driver
<CD>:\Common\LAN_driver\R8139_810x LAN driver
<CD>:\Common\Ac97_codec\Realtek\ALC202A Audio driver
<CD>:\Common\VIA\USB2.0 USB2.0 driver

/37
5
2. I/O Function
2.1 POS 4000 Front View
Optional 1:
# Function
1 Power & HDD Indicator
2 Key Lock
3 Power Button
4 USB3 & 4
5 Slim CD-ROM
6 Compact Flash
Optional 2:
# Function
1 Power & HDD Indicator
2 Key Lock
3 Power Button
4 USB3 & 4
5 Floppy Disc Drive
6 Compact Flash
1
64
5
2
3
1
6
4
5
2
3

/37
6
2.2 POS 4000 Rear View
# Function # Function
7 AC Inlet 14 VGA
8 USB 1 & 2 15 LAN
9 LPT 16 COM4
10 PS/2 Mouse 17 DC Output 24V/2.0A
11 PS/2 Keyboard 18 Cash drawer
12 COM2 19 COM3
13 COM1 20 Line out
Note: DC output 24 V Pin Assignment
Pin Assignment
1 NC
2 + 24V DC
3 Ground
12 14 15
11 1398
7 10
20
16 17 18 19

/37
7
3. Specification
3.1 B69 & B79
Model 4691 4791
MB B69 all-in-one Mainboard B79 all-in-one Mainboard
Core logic Intel 82815E B-STEP GMCH &
82801BA ICH2 Intel 82845GV GMCH & 820801DB ICH4
CPU Intel socket 370 CPU Celeron /PIII
FC-PGA/FC-PGA2 Intel socket 478 CPU Celeron /P4 400/533 PSB with Hyper Threading
Technology support
System memory 2x 168pin DIMM sockets support
100/133 MHz SDRAM up to 512MB 2 x DDR DIMM 200/266/333 up to 2GB
BIOS Award PnP BIOS
VGA display BUILT-IN GMCH
Maximum resolution is up to
resolution of 1600x1200 pixels.
Built-in GMCH
Maximum resolution is up to
resolution of 1920x1080 pixels.
The internal graphics device use share system main memory structure
and supports Intel Dynamic Video Memory Technology (D.V.M.T.). Intel
D.V.M.T. dynamically responds to application requirements by allocating
the proper amount of display and texturing memory taken from system
memory by driver control.
VGA memory
1MB On-Chip Frame Buffer Size for
legacy OS. For legacy OS, user control the 1MB/8MB On-Chip Frame Buffer
Size by BIOS SETUP.
I/O controller W83627HF x 1, W83697 HF x1
LAN controller Realtek RTL8100BL 10/100Mb fast Ethernet controller
Support WOL & boot from LAN
IDE controller Built-in core logic support UDMA 33/66/100Mhz
HDD connector Primary: 1x 40-pin 2.54 pitch
Secondary: 1x 44pin 2.0 pitch, 1x Compact Flash socket
FDD connector 1x 34-pin 2.54 pitch
Audio controller AC’97 ADI AD1881A (2ch)
1x PCI slot
Expansion Slot Optional: 1xISA slot
Main board
dimension 232x313mm
1 x 3.5” HDD drive bay
Storage Device Optional:
1 x 3.5” FDD drive /(1 x slim CD-ROM /CD-RW/DVD-ROM drive bay)

/37
8
I/O Port Rear Panel:
1 x PS2 keyboard port
1 x PS2 Mouse port
2 x DB-9M RS-232 serial ports
(COM1/COM2, pin1 & 9 with 5V/12V power select)
1 x DB25F Parallel port
1 x DB15F VGA port
1 x RJ45 LAN port
2 x USB ports
1 x Line out
POS I/O port
1 x RJ11 cash drawer port
1 x 24V POS printer power port (max. 24V/2A)
2 x DB-9M RS-232 serial ports
(COM3/COM4, pin1 & pin9 with 5V/12V power selectable)
Front Panel:
1 x Compact Flash socket
2 x USB ports
Power Supply FT8180 internal ATX 180W
System
Dimension
240(w) x 335(d) x 72 (h) mm without cable manage cover
Thermal CPU Cooler x1
Support hardware monitor for fan speed control and software throttling
Customer
Display Optional: LED / VFD/ Graphic Customer Display
Pole height (9 / 22 cm)
EMC FCC/CE Class B
CE mark: EN55022 / EN61000 -3-2 2000 / EN61000-3-3 / EN55024
Safety LVD: EN60950 2000
Case Color Computer white/ Silver black
OS Support Win98/2000/XP/NT 4.0,Linux

/37
9
3.2 B49
Model 4491
M/B B49
Core Logic VIA CLE266 (VT8623CE ) North Bridge
VIA VT8235CD South Bridge
CPU
VIA Eden / C3 EBGA Processors
Support for VIA C3 EBGA processors
133/100/66MHZ CPU Front Side BUS (FSB)
C3 EBGA 733 / 800 / 1.0G / 1.2G or High (Optional)
C3 EBGA 800 Standard to Use
System Memory 2 x DDR266/200 DIMM up to 2Gbyte memory size
BIOS Award PnP BIOS
Video Display Integrated ProSavage8 2D/3D VideoAccelerator
MPEG-2 video textures
2D/3D resolutions up to 1400 x 1050 x 32
V
ideo Memory 16/32/64 MB frame buffer using system memory
I/O Controller Winbond 83697HFx1, 83697HFx1, 83697UFx1
LAN controller Realtek RT8100BL 10/100Mb fast Ethernet controller
Support Wake-On-LAN and boot from LAN
TV – Out PAL / NTSC multi system support
VIA VT1622A TV Out (TV Encoder)
1 x 8pin-header support RCA /S-Video interface (Optional)
HDD connector Primary: 1x 40-pin 2.54 pitch
Secondary: 1x 44pin 2.0 pitch, 1x Compact Flash socket
FDD connector 1x 34-pin 2.54 pitch
USB Controller VT8235 Integrated support USB2.0
A
udio controller AC’97 Realtek ALC202A(2ch)
Expansion Slot 1 x PCI slot
M/B dimension 232 mm (W) x 314 mm (D)
1 x 3.5” HDD drive bay
Storage Device Optional:
1 x 3.5” FDD drive /(1 x slim CD-ROM /CD-RW/DVD-ROM drive bay)
Power supply FT8180 internal ATX 180W
System
Dimension
240(w) x 335(d) x 72 (h) mm without cable manage cover
Thermal CPU Cooler x1
Support hardware monitor for fan speed control and software throttling
Customer
Display Optional: LED / VFD/ Graphic Customer Display
Pole height (9 / 22 cm)

/37
10
EMI CE Class B
FCC Class B
I/O port Rear Panel:
2 x USB 2.0 ports
1 x DB-25F Parallel port
1 x 1*6Pin Double PS2 Keyboard / Mouse port
2 x DB-9M RS-232 Serial port
1 x DB-15F VGA port
1 x RJ-45 LAN port
1 x Audio jacks: line-out
1 x Line out
POS I/O port
1 x RJ11 cash drawer port
1 x 24V POS printer power port (max. 24V/2A)
2 x DB-9M RS-232 serial ports
(COM3/COM4, pin1 & pin9 with 5V/12V power selectable)
Option1:
1 x 2nd printer port on slot bracket
Option2:
2 x USB 2.0 ports (for slot user, support pin header)
Front Panel:
2 x USB 2.0 ports
1 x compact flash
OS Support Windows 9x/ME/NT 4.0/2000/XP
Linux

/37
11
3.3 System Memory Combination
POS 4000 B69
RAMSize
Slot 128MB 256MB 512MB
DIMM1 X 128 128 256 X 256 512 X
DIMM2 128 X 128 X 256 256 X 512
POS 4000 B79
RAMSize
Slot 128MB 256MB 512MB 1024MB 2048MB
DIMM1 X 128 128 256 X 256 512 X 512 1024 X 1024
DIMM2 128 X 128 X 256 256 X 512 512 X 1024 1024
NOTE:
1. Optimal Combination
CPU system bus 400 533
DIMM DDR 266 DDR 333
2. In B79 memory 2048MB combination, if you want to use double stack memory that
your DIMM1 and DIMM2 all should be double stack memory.
POS 4000 B49
RAMSize
Slot 128MB 256MB 512MB 1024MB 2048MB
DIMM1 X 128 128 256 X 256 512 X 512 1024 X 1024
DIMM2 128 X 128 X 256 256 X 512 512 X 1024 1024

/37
12
4. Jumper Setting
4.1 B69 M/B
DIMM1
FAS_CPU1
FAS_SYS1
RJ45-1
CN4
CN9
USB2
SW1
U49
USB3
CN6
IDE3
U45
BAT4
U46
PWR1
U47
CN5
U11
U14
CN2
DIMM2
DATA1
JP1
CN1
JP2
FDD1
IDE2
U7
U8
VGA1 COM1 COM2
PS1
PRN1
USB1
U24
JP7
JP3
JP5
JP6
JP4

/37
13
4.1.1 COM 1 Power Selection * Default Setting
Pin Function JP1 (SHORT)
*DCD# 1-2
VCC 3-4
1
+12V 5-6
*RI# 7-8
VCC 9-10
9
+12V 11-12
4.1.2 COM 2 Power Selection
Pin Function JP2 (SHORT)
*DCD# 1-2
VCC 3-4
1
+12V 5-6
*RI# 7-8
VCC 9-10
9
+12V 11-12
4.1.3 Power Mode Selection
Function JP3
*ATX Power OPEN
AT Power SHORT
4.1.4 CMOS Operation modes
Function JP6
*CMOS Normal OPEN
CMOS Reset SHORT
4.1.5 Compact Flash Master/Slave Setting
Function JP7
*Master OPEN
Slave SHORT
Note:
OPEN SHORT

/37
14
4.2 B79 M/B
PWR2
CN9 SW1
USB3USB2
CN6
CPU1
FAN-SYS
FAN-CPU
IDE3
RJ45-1
DIMM1
U7
BAT1
U18
PWR1
CN5
U19
CN4
U14 FDD1
U11
JP6
JP4
JP5
JP7
JP3 CN2
IDE2
DIMM2
DATA1
JP1
CN1
JP2
COM1
VGA1 COM2
PS1
U8
PRN1
USB1
U24

/37
15
4.2.1 COM 1 Power Selection *DefaultSetting
Pin Function JP1(SHORT)
*DCD# 1-2
VCC 3-4
1
+12V 5-6
*RI# 7-8
VCC 9-10
9
+12V 11-12
4.2.2 COM 2 Power Selection
Pin Function JP2(SHORT)
*DCD# 1-2
VCC 3-4
1
+12V 5-6
*RI# 7-8
VCC 9-10
9
+12V 11-12
4.2.3 Power Mode Selection
Function JP3
*ATX Power OPEN
AT Power SHORT
4.2.4 CMOS Operation mode
Function JP6
*CMOS Normal OPEN
CMOS Reset SHORT
4.2.5 Compact Flash Master/Slave Setting
Function JP7
*Master OPEN
Slave SHORT
Note:
OPEN SHORT

/37
16
4.3 B49 M/B

/37
17
4.3.1 COM1 Power Select *DefaultSetting
Pin JP1(SHORT)
*DCD# 1-2
+5V 3-4
1 +12V 5-6
*RI# 7-8
+5V 9-10
9 +12V 11-12
4.3.2 COM2 Power Select
Pin JP2 (SHORT)
*DCD# 1-2
+5V 3-4
1 +12V 5-6
*RI# 7-8
+5V 9-10
9 +12V 11-12
4.3.3 Power Mode Setting
Function JP3 (SHORT)
* ATX Power 1-2
AT Power 2-3
4.3.4 CMOS Clear Selection
Function JP6 (SHORT)
* Normal 1-2
Clear 2-3
4.3.5 Compact Flash Master/Slave Setting
Function JP7
* Master SHORT
Slave OPEN
Note:
OPEN SHORT

/37
18
4.4 POS I/O Board Jumper Setting
4.4.1 COM 3 Power Selection *DefaultSetting
Pin Function JP4(SHORT)
*DCD# 1-2
VCC 3-4
1
+12V 5-6
*RI# 7-8
VCC 9-10
9
+12V 11-12
4.4.2 COM 4 Power Selection
Pin Function JP3(SHORT)
*DCD# 1-2
VCC 3-4
1
+12V 5-6
*RI# 7-8
VCC 9-10
9
+12V 11-12
4.4.3 Cash Drawer Power Selection
Function JP2(SHORT)
24V 1-2
*12V 2-3
Note:
OPEN SHORT

/37
19
5. Driver Installation
5.1 B69 M/B
The following procedures are for Windows 98SE, other platforms are similar.
5.1.1 Chipset Driver Installation
Driver path: <CD>:\Common\INTEL\Chipset
a. Click "Intel_Chipset_4_20_1006" on the
My Computer window. b. Click "Next" button on the welcome window.
c. Click "Next" button on the License
Agreement window. d. Click "Next" button on the Read me Information window.

/37
20
e. Click ”Finish” and restart your system.
5.1.2 VGA Driver Installation
Driver path: <CD>:\Common\INTEL\i815VGA
a. Click "Setup" on the My Computer window. b. Click "Next" button on the welcome window.
c. Click "Next" button on the License
Agreement window. d. Click ”Finish” and restart your system.