Venture Products Ventrac ET202 User manual

Operator’s Manual
Turbine Blower
VENTRAC.COM
Revised 04/12/23
09.10179 Rev. 01
Original Operator’s Manual
ET202

2
To the Owner

If you need to contact an authorized Ventrac dealer for information on servicing your product, al-
ways provide the product model and serial numbers.
Please ll in the following information for future reference. See the picture(s) below to nd the loca-
tion of the identication numbers. Record them in the spaces provided.
Date of Purchase:
Dealer:
Dealer Address:
Dealer Phone Number:
Dealer Fax Number:
Model # (A): __________________________________
Serial # (B):____________________________________

Venture Products Inc. reserves the right to make chang-
es in design or specications without obligation to make
like changes on previously manufactured products.
500 Venture Drive
Orrville Oh 44667

View all manuals
Visit ventrac.com/manuals for the
latest version of this operator’s
manual.
A downloadable parts manual is also
available.
A
B

TABLE OF CONTENTS
3
 
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Why Do I Need an Operator’s Manual? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Using Your Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Manual Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
 
General Safety Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Training Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Requirements for Personal Protective Equipment (PPE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operation Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Keep Riders O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Operating On Slopes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Roadway Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Truck Or Trailer Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Fuel Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Hydraulic Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
ET202 Safety Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Safety Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
 
Discharge Nozzle Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Weight Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Optional Lights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
 
Daily Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Attaching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Detaching. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Operating Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Transport of the Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
 
Cleaning and General Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Belt Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Attachment Belt Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Turbine Fan Belt Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Nozzle Rotation Belt Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Turbine Fan Belt Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Nozzle Rotation Belt Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Lubrication Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Maintenance Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
 
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Introduction - 4
INTRODUCTION
Accessories Item Description Part Number
Light Kit 70.8230
Product Description
The Ventrac ET202 turbine blower is designed to blow large volumes of air and is much quieter than a conven-
tional blower. The turbine blower can be used to blow leaves, light snow, and to remove debris from sidewalks,
parking lots, and other areas.
The turbine blower’s front discharge nozzle can be hydraulically rotated 360 degrees. The turbine blower can
be used to clear paths by pointing the discharge nozzle down. The discharge nozzle can be pointed to either
side of the blower to move debris in the desired direction. The discharge nozzle can be pointed up to remove
loose leaves from trees.
An optional light kit*provides additional lighting to the right and left sides of the turbine blower.
*The power unit must be equipped with an optional 12 volt front kit.
Why Do I Need an Operator’s Manual?
This manual has been created to help you gain the important knowledge of what is needed to safely operate and
maintain your machine, and to avoid injury and product damage. It is divided into chapters for convenient refer-
ence of the appropriate information.
You must read and understand the operator’s manual for each piece of Ventrac equipment you own. Read-
ing the operator’s manual will help you become familiar with each specic piece of equipment. If this manual
becomes damaged or unreadable, it should be replaced immediately. Contact your local Ventrac dealer for a
replacement.
When using a Ventrac attachment, be sure to read and follow the safety and operating instructions of both the
power unit and the attachment being used to ensure the safest operation possible.
The information in this manual provides the operator with the safest procedures to operate the machine while
getting the maximum use out of the unit. Failure to follow the safety precautions listed in this manual may
result in personal injury and/or damage to the equipment.
Venture Products Inc. is pleased to provide you with your new
Ventrac turbine blower! We hope that Ventrac equipment will
provide you with a ONE Tractor Solution.
Please visit our website, or contact your authorized Ventrac
dealer for a complete list of items available for your new turbine
blower.

INTRODUCTION
Introduction - 5
Using Your Manual
This manual identies potential hazards and safety
concerns to help you, as well as others, avoid person-
al injury and/or damage to the equipment.
Safety should always be the rst priority when work-
ing on or operating equipment. Accidents are more
likely to occur when proper operating procedures are
not followed or inexperienced operators are involved.
SYMBOL DEFINITIONS
This symbol identies potential health and
safety hazards. It marks safety precau-
tions. Your safety and the safety of others is
involved.
There are three signal words that describe the level of
safety concern: Danger, Warning, and Caution.
SIGNAL WORD DEFINITIONS
DANGER
Indicates an imminently hazardous situation which, if
not avoided, will result in death or serious injury. This
signal word is limited to the most extreme cases.
WARNING
Indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury
and/or property damage. It may also be used to alert
against unsafe practices.
This manual also uses two words to highlight informa-
tion. ATTENTION calls attention to special mechanical
information to prevent equipment damage and/or best
practices for equipment service and care.
NOTE emphasizes general information that is worthy
of special attention.
Note: Right-Hand and Left-Hand orientations may be
referred to at dierent places throughout this manual.
Right-Hand and Left-Hand is determined as if facing
forward from the operator station.
Manual Glossary
Power Unit A Ventrac tractor or other Ventrac engine powered device that may be operated by itself or with
an attachment or accessory.
Attachment A piece of Ventrac equipment that requires a Power Unit for operation.
Accessory A device that attaches to a Power Unit or Attachment to extend its capabilities.
Machine Describes any “Attachment” or “Accessory” that is used in conjunction with a power unit.

Safety - 6
SAFETY
General Safety Procedures
for Ventrac Power Units, Attachments, & Accessories
Training Required
• The owner of this machine is solely responsible for properly training the operators.
• The owner/operator is solely responsible for the operation of this machine and for the prevention of ac-
cidents or injuries occurring to him/herself, other people, or property.
• Do not allow operation or service by children or untrained personnel. Local regulations may restrict the
age of the operator.
• Before operating this machine, read the operator’s manual and understand its contents.
• If the operator of the machine cannot understand this manual, then it is the responsibility of this machine’s
owner to fully explain the material within this manual to the operator.
• Learn and understand the use of all the controls.
• Know how to stop the power unit and the attachments quickly in the event of an emergency.
Requirements for Personal Protective Equipment (PPE)
• The owner is responsible for ensuring that all the operators use the proper PPE while operating the ma-
chine. Whenever you use the machine, use the following PPE:
• Certied eye protection and hearing protection.
• Closed toe, slip resistant footwear.
• Long pants or trousers.
• A dust mask for dusty conditions.
• Additional PPE may be required. Refer to the product safety procedures for any additional requirements.
Operation Safety
• Secure long hair and loose clothing. Do not wear jewelry.
• Inspect the machine before operation. Repair or replace any damaged, worn, or missing parts. Be sure the
guards and shields are in proper working condition and are secured in place. Make any necessary adjust-
ments before operating the machine.
• Some pictures in this manual may show shields or covers opened or removed in order to clearly illustrate the
instructions. Under no circumstance should the machine be operated without these devices in place.
• Alterations or modications to this machine can reduce safety and could cause damage to the machine. Do
not alter the safety devices or operate with the shields or covers removed.
• Before each use, verify that all the controls function properly and inspect all the safety devices. Do not op-
erate if the controls or safety devices are not in proper working condition.
• Check the parking brake function before operating. Repair or adjust the parking brake if necessary.
• Observe and follow all of the safety decals.
• All the controls are to be operated from the operator’s station only.
• Always wear a seat belt if the machine has a roll cage/bar installed and in the upright position.

SAFETY
Safety - 7
General Safety Procedures
for Ventrac Power Units, Attachments, & Accessories
• Ensure the attachment or accessory is locked or fastened securely to the power unit before operating.
• Ensure that all bystanders are clear of the power unit and the attachment before operating. Stop the ma-
chine if someone enters your work area.
• Always be alert to what is happening around you, but do not lose focus on the task you are performing.
Always look in the direction the machine is moving.
• Look behind and down before backing up to be sure of a clear path.
• If you hit an object, stop and inspect the machine. Make any necessary repairs before operating the ma-
chine again.
• Stop operation immediately at any sign of equipment failure. An unusual noise can be a warning of equipment
failure or a sign that maintenance is required. Make any necessary repairs before operating the machine again.
• If equipped with a high/low range feature, never shift between high and low range while on a slope. Always
move the machine to level ground and engage the parking brake before shifting range.
• Do not leave the machine unattended while it is running.
• Always park the machine on level ground.
• Always shut o the engine when connecting the attachment drive belt to the power unit.
• Never leave the operator’s station without lowering the attachment to the ground, engaging the parking
brake, shutting o the engine, and removing the ignition key. Make sure all moving parts have come to a
complete stop before dismounting.
• Never leave the machine unattended without lowering the attachment to the ground, engaging the park-
ing brake, shutting o the engine, and removing the ignition key.
• Only operate in well-lit conditions.
• Do not operate when there is a risk of lightning.
• Never direct the discharge of any attachment in the direction of people, buildings, animals, vehicles, or
other objects of value.
• Never discharge material against a wall or obstruction. The material may ricochet back toward the operator.
• Use extra caution when approaching blind corners, shrubs, trees, or other objects that may obscure your vi-
sion.
• Do not run the engine in a building without adequate ventilation.
• Do not touch the engine or the muer while the engine is running or immediately after stopping the en-
gine. These areas may be hot enough to cause a burn.
• Do not change the engine governor settings or over-speed the engine. Operating the engine at excessive
speeds may increase the hazard of personal injury.
• To reduce the hazard of re, keep the battery compartment, engine, and muer areas free of grass, leaves,
excessive grease, and other ammable materials.
• Clear the working area of objects that might be hit or thrown from the machine.

SAFETY
Safety - 8
General Safety Procedures
for Ventrac Power Units, Attachments, & Accessories
• Keep people and pets out of the working area.
• Know the work area well before operation. Do not operate where traction or stability is questionable.
• Reduce speed when you are operating over rough ground.
• Equipment can cause serious injury and/or death when improperly used. Before operating, know and un-
derstand the operation and safety of the power unit and the attachment being used.
• Do not operate the machine if you are not in good physical and mental health, if you will be distracted by
personal devices, or if you are under the inuence of any substance which might impair your decisions,
dexterity, or judgment.
• Children are attracted to machine activity. Be aware of children and do not allow them in the work area.
Turn o the machine if a child enters the work area.

• Only allow the operator on the power unit. Keep riders o.
• Never allow riders on any attachment or accessory.
Operating On Slopes
• Slopes can cause loss-of-control and tip-over accidents, which can result in severe injury or death. Be familiar
with the emergency parking brake, along with the power unit controls and their functions.
• If the power unit is equipped with a fold down roll bar, it must be locked in the upright position when operating
on any slope.
• Use low range (if equipped) when operating on slopes greater than 15 degrees.
• Do not stop or start suddenly when operating on slopes.
• Never shift between high and low range while on a slope. Always move the power unit to level ground and
engage the parking brake before shifting range or placing the power unit in neutral.
• Variables such as wet surfaces and loose ground will reduce the degree of safety. Do not drive where the
machine could lose traction or tip over.
• Keep alert for hidden hazards in the terrain.
• Stay away from drop-os, ditches, and embankments.
• Sharp turns should be avoided when operating on slopes.
• Pulling loads on hills decreases safety. It is the responsibility of the owner/operator to determine loads that
can safely be controlled on slopes.
• Transport the machine with the attachment lowered or close to the ground to improve stability.
• While operating on slopes, drive in an up and down direction whenever possible. If turning is necessary
while driving across slopes, reduce your speed and turn slowly in the downhill direction.
• Ensure a sucient supply of fuel for continuous operation. A minimum of one-half tank of fuel is recommended.

SAFETY
Safety - 9
General Safety Procedures
for Ventrac Power Units, Attachments, & Accessories
Roadway Safety
• Operate with safety lights when operating on or near roadways.
• Obey all state and local laws concerning operation on roadways.
• Slow down and be careful of trac when operating near or crossing roadways. Stop before crossing roads
or sidewalks. Use care when approaching areas or objects that may obscure vision.
• If there is any doubt of safety conditions, discontinue the machine operation until a time when the opera-
tion can be performed safely.
• When operating near or on roadways, have a Slow Moving Vehicle Emblem clearly displayed.
Truck Or Trailer Transport
• Use care when loading or unloading the machine into a truck or trailer.
• Use full width ramps for loading the machine into a truck or trailer.
• The parking brake is not sucient to lock the machine during transport. Always secure the power unit and/
or attachment to the transporting vehicle securely using straps, chains, cables, or ropes. Both the front and
rear straps should be directed down and outward from the machine.
• Shut o the fuel supply to the power unit during transport on a truck or trailer.
• If equipped, turn the battery disconnect switch to the O position to shut o electrical power.
Maintenance
• Keep the safety decals legible. Remove all grease, dirt, and debris from the safety decals and instructional labels.
• If any decals are faded, illegible, or missing, contact your dealer promptly for replacements.
• When new components are installed, be sure that the current safety decals are axed to the replacement
components.
• If any component requires replacement, use only original Ventrac replacement parts.
• Always turn the battery disconnect to the O position or disconnect the battery before performing any re-
pairs. Disconnect the negative terminal rst and the positive terminal last. Reconnect the positive terminal
rst and the negative terminal last.
• Keep all bolts, nuts, screws, and other fasteners properly tightened.
• Always lower the attachment to the ground, engage the parking brake, shut o the engine, and remove the
ignition key. Make sure all moving parts have come to a complete stop before cleaning, inspecting, adjust-
ing, or repairing.
• If the power unit, attachment, or accessory requires repairs or adjustments not instructed in the operator’s
manual, the power unit, attachment, or accessory must be taken to an authorized Ventrac dealer for service.
• Never perform maintenance on the power unit and/or attachment if someone is in the operator’s station.
• Always use protective glasses when handling the battery.

SAFETY
Safety - 10
General Safety Procedures
for Ventrac Power Units, Attachments, & Accessories
• Check the fuel lines for tightness and wear on a regular basis. Tighten or repair them as needed.
• To reduce the hazard of re, keep the battery compartment, engine, and muer areas free of grass, leaves,
and excess grease.
• Do not touch the engine, the muer, or other exhaust components while the engine is running or immedi-
ately after stopping the engine. These areas may be hot enough to cause a burn.
• Allow the engine to cool before storing and do not store near an open ame.
• Do not change the engine governor settings or over-speed the engine. Operating engine at excessive
speeds may increase the hazard of personal injury.
• Springs may contain stored energy. Use caution when disengaging or removing springs and/or spring
loaded components.
• An obstruction or blockage in a drive system or moving/rotating parts may cause a buildup of stored en-
ergy. When the obstruction or blockage is removed, the drive system or moving/rotating parts may move
suddenly. Do not attempt to remove an obstruction or blockage with your hands. Keep your hands, feet,
and clothing away from all power-driven parts.
Fuel Safety
• To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely
ammable and the vapors are explosive.
• Do not refuel the machine while smoking or at a location near ames or sparks.
• Always refuel the machine outdoors.
• Do not store the machine or fuel container indoors where the fumes or fuel can reach an open ame,
spark, or pilot light.
• Only store fuel in an approved container. Keep out of the reach of children.
• Never ll containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place the containers
on the ground away from your vehicle before lling.
• Remove the machine from the truck or trailer and refuel it on the ground. If this is not possible, refuel the
machine using a portable container, rather than from a fuel dispenser nozzle.
• Never remove the fuel cap or add fuel with the engine running. Allow the engine to cool before refueling.
• Never remove the fuel cap while on a slope. Only remove the fuel cap when parked on a level surface.
• Replace the fuel tank cap and the container cap securely.
• Do not overll the fuel tank. Only ll to the bottom of the fuel neck, do not ll the fuel neck full. Overlling
of the fuel tank could result in engine ooding, fuel leakage from the tank, and/or damage to the emissions
control system.
• If fuel is spilled, do not attempt to start the engine. Move the power unit away from the fuel spill and avoid
creating any source of ignition until the fuel vapors have dissipated.

SAFETY
Safety - 11
General Safety Procedures
for Ventrac Power Units, Attachments, & Accessories
• If the fuel tank must be drained, it should be drained outdoors into an approved container.
• Check the fuel lines for tightness and wear on a regular basis. Tighten or repair them as needed.
• The fuel system is equipped with a shut-o valve. Shut o the fuel when transporting the machine to and
from the job, when parking the machine indoors, or when servicing the fuel system.
Hydraulic Safety
• Make sure the hydraulic connections are tight and all hydraulic hoses and tubes are in good condition. Re-
pair any leaks and replace any damaged or deteriorated hoses or tubes before starting the machine.
• Hydraulic leaks can occur under high pressure. Hydraulic leaks require special care and attention.
• Use a piece of cardboard and a magnifying glass to locate suspected hydraulic leaks.
• Keep your body and hands away from pinhole leaks or nozzles that eject high pressure hydraulic uid. Hy-
draulic uid escaping under high pressure can penetrate the skin causing serious injury, leading to severe
complications and/or secondary infections if left untreated. If hydraulic uid is injected into the skin, seek
immediate medical attention no matter how minor the injury appears.
• The hydraulic system may contain stored energy. Before performing maintenance or repairs on the hydrau-
lic system, remove any attachments, engage the parking brake, disengage the weight transfer system (if
equipped), shut o the engine, and remove the ignition key. To relieve pressure on the auxiliary hydraulic
system, shut o the power unit engine and move the hydraulic control lever left and right before disconnect-
ing the auxiliary hydraulic quick couplers.

SAFETY
Safety - 12
ET202 Safety Procedures
• The turbine blower produces strong wind speeds which can blow loose objects at high velocity, causing damage
or injury to other objects, buildings, vehicles, people, or animals. Remove all loose objects from the work area.
• Never direct the discharge nozzle in the direction of people, buildings, animals, vehicles, or other objects of
value.
• Do not attempt to clear leaves or other debris from the intake shield of the discharge nozzle while the machine
is running. Always lower the attachment to the ground, engage the parking brake, shut o the engine, and
remove the ignition key. Make sure all moving parts have come to a complete stop before attempting to clear a
blockage.
• The attachment hydraulic system may contain stored energy. Before performing maintenance or repairs
on the hydraulic system, the attachment’s auxiliary hydraulic hoses must be disconnected from the power
unit. Lower the attachment to the ground, shut o power unit engine, move the secondary SDLA lever left
and right to relieve auxiliary hydraulic pressure, and disconnect the auxiliary hydraulic quick couplers.
• Store the turbine blower with the discharge nozzle pointed down to prevent any debris or foreign objects
from entering the blower.

SAFETY
Safety - 13
Safety Decals
The following safety decals must be maintained on your attachment.
Keep all safety decals legible. Remove all grease, dirt, and debris from safety decals and instructional labels. If
any decals are faded, illegible, or missing, contact your dealer promptly for replacements.
When new components are installed, be sure that current safety decals are axed to the replacement compo-
nents.
B
A
A
B
C
D
E
F
G

SAFETY
Safety - 14
Decal Description Part Number Quantity
A Turbine Blower Hazard 00.0682 2
B Finger/Hand Entanglement Hazard 00.0631 2
CShield Missing 00.0625 1
D Read Operator’s Manual 00.0619 1
E Entanglement Hazard 00.0626 1
F Moving Parts Hazard 00.0632 1
G High Pressure Fluid Hazard 00.0621 1
1. Thrownobjecthazard.Keepbystanders
awayfromthemachine.
2. Cutting/dismembermenthazardofhands.
Keephandsawayfrommovingparts.Keep
allguardsandshieldsinplace.
1. Shieldmissing-donotoperate.
2. Pinchingorcrushinghazard.
3. Fingersorhandentanglement.
1. Fingersorhandentanglement.
Stayawayfrommovingparts.
1 2
1
12
3
1. Readtheoperator’smanual.
1
1. Fingersorhandentanglement.
2. Stayawayfrommovingparts.
3. Keepallguardsandshieldsinplace.
1. Stayawayfrommovingparts.
2. Keepallguardsandshieldsinplace.
A B C
D E F
1
23
1
2
G
Highpressure󽘁uidhazard.
1. Keepyourbodyandhandsawayfrom
suspectedhydraulicleaks.
2. Weareyeprotectionwheninspectingthe
hydraulicsystemforleaks.

Operation - 15
OPERATIONAL CONTROLS
Discharge Nozzle Rotation
The discharge nozzle rotation is controlled with the
power unit’s secondary SDLA control lever*. Move the
secondary SDLA lever to the left or right to rotate the
discharge nozzle to the desired direction. Release the
lever when the discharge nozzle is pointing in the
desired direction.
Weight Transfer
Terrain and ground conditions may aect the ap-
propriate setting for the power unit’s weight transfer
system*. Engaging the weight transfer system helps
prevent the turbine blower’s front caster wheel from
sinking into soft ground by decreasing the amount of
weight on the caster wheel.
Optional Lights
If the turbine blower is equipped with an optional
light kit, turn the lights on by pressing the top of the
rocker switch on the 12 volt knob on the power unit’s
primary SDLA control lever*. Press the bottom of the
rocker switch to turn the lights o.
*Refer to power unit operator’s manual for operation of power unit controls.

Operation - 16
GENERAL OPERATION
Daily Inspection
WARNING
Always engage the parking brake, shut o the pow-
er unit engine, remove the ignition key, and ensure
that all moving parts have come to a complete stop
before inspecting the components, or attempting
any repair or adjustment.
1. Park the machine on a level surface, with the en-
gine shut o and all uids cold.
2. Perform a visual inspection of both the power
unit and the attachment. Look for loose or miss-
ing hardware, damaged components, or signs of
wear.
3. Inspect the hydraulic hoses and the hydraulic t-
tings to ensure tight, leak free connections.
4. Inspect the belts for damage or excessive wear.
Refer to the Belt Inspection section of this manual.
5. Inspect the inlet, blower housing, and discharge
nozzle for foreign objects or material. Clean these
areas as needed before operating.
Attaching
1. Drive the power unit slowly forward into the hitch
arms of the attachment. Align the lift arms of the
power unit with the attachment hitch arms by
raising or lowering the front hitch and complete
the engagement.
2. Once completely engaged, close the front hitch
locking lever.*
3. Engage the parking brake* and shut o the en-
gine.
4. Place the attachment belt onto the PTO drive pul-
ley on the power unit. Ensure the belt is properly
seated in each pulley.
5. Engage the PTO belt tensioner rod.
6. Wipe the hose ends clean and connect to the
power unit’s hydraulic quick couplers. If equipped,
connect the hoses and the quick couplers so the
colored indicators are paired together (red to red,
etc.).
7. If the turbine blower is equipped with a light kit,
connect the electric plug to the power unit.
8. Raise the jack stand to the highest position and
secure with the latch pin.
Detaching
1. Park the power unit on a level surface and engage
the parking brake.*
2. Lower the attachment to the ground.
3. Rotate the discharge nozzle so it is pointing down
toward the ground.
4. Shut o the power unit engine.
5. Disengage the PTO belt tensioner rod.
6. Remove the attachment belt from the PTO drive
pulley of the power unit.
7. Disconnect the hydraulic quick couplers from the
power unit and store the hose ends in the frame
holes in front of the intake screen.
8. If the turbine blower is equipped with a light kit,
disconnect the electric plug from the power unit.
9. Lower the jack stand to the lowest position pos-
sible and secure with the latch pin.
10. Disengage the front hitch locking lever.*
11. Restart the power unit and slowly back away from
the attachment. A side to side movement of the
steering wheel may aid in disengagement.
Operating Procedure
Before operation, perform the daily inspection and set
the power unit’s weight transfer system.
Lower the turbine blower to the ground and place the
power unit’s primary SDLA lever in the oat position.
Set the discharge nozzle to the desired direction.
With the power unit engine running between 2,000
and 2,500 RPM, engage the PTO switch. Increase the
engine speed until there is sucient force to accom-
plish the blowing task.
When blowing leaves or debris, observe the wind di-
rection and work with the wind whenever possible.
When clearing a large area, make a pass while blow-
ing material in the desired direction. Move over close
to the edge of the material and make another pass.
Continue until the entire area is clear.
Transport of the Attachment
Transport the attachment with the power unit front
hitch and attachment fully raised to reduce wear of
the equipment. Travel slowly when transporting over
undulating and rough surfaces to maintain control of
the power unit and to reduce the shock to the power
unit and the attachment. Always disengage the power
unit PTO before transporting the attachment.
*Refer to power unit operator’s manual for operation of power unit controls.

Service - 17
SERVICE
WARNING
Always engage the parking brake, shut o the pow-
er unit engine, remove the ignition key, and ensure
that all moving parts have come to a complete stop
before inspecting the components, or attempting
any repair or adjustment.
ATTENTION
If any component requires replacement, use only
original Ventrac replacement parts.
Cleaning and General Maintenance
For best results, and to maintain the nish of the
turbine blower, clean or wash the turbine blower after
each use to remove leaves, dirt, and other debris.
If a buildup of dirt or debris occurs on the turbine ns
or in the blower housing, the blower eciency can be
aected and a loss of air volume and velocity may be
noticed. If this occurs, clean the ns and the housing
using an air nozzle with an extension or with low pres-
sure water.
ATTENTION
Do not spray water into the blower while the ma-
chine is running.
Belt Inspection
Inspecting the drive belts of the attachment can
prevent sudden belt failure by nding problems
before they cause a belt to break.
Glazing Streaked Sidewall
Cracks
Separation
Tensile Break
Typical wear
on a drive
belt may
result in the
conditions
shown in the
diagram. If
any of these
conditions
occur, the drive belt will require replacement.
Attachment Belt Replacement
1. Remove the turbine blower from the power unit.
A
2. Remove the
drive pulley
shield (A) from
the turbine
blower.
3. Remove the old
belt and install
the new attach-
ment belt onto
the drive pulley.
4. Reinstall the drive pulley shield.
Turbine Fan Belt Replacement
1. Remove the turbine blower from the power unit.
2. Remove the inlet screen (A) from the turbine
blower.
3.
A
Release the turbine fan belt tension spring.
CAUTION
The spring may be under high tension. Use caution
when releasing the spring to prevent pinching.
4. Remove the old belt and install a new belt onto
the pulleys.
5. Engage the turbine fan belt tension spring.
6. Reinstall the inlet screen.

SERVICE
Service - 18
Nozzle Rotation Belt Replacement
1. Remove the extension spring (A) from the frame
bolt to release the belt tension.
2.
A
Remove the old belt and install a new belt onto
the discharge nozzle and the motor pulley.
3. Reinstall the extension spring onto the frame bolt
to apply tension to the belt.
Turbine Fan Belt Adjustment
1. Remove the turbine blower from the power unit.
2. Remove the inlet screen (A) from the turbine
blower.
3.
A
To increase the belt tension, move the spring
down to the next frame notch.
4. Reinstall the inlet screen.
Nozzle Rotation Belt Adjustment
Due to dierences in air pressure, the nozzle may
rotate freely at lower engine RPM but become erratic
or stop entirely at high engine RPM. If this occurs,
lubricate the nozzle slides as specied in the lubrica-
tion section and/or increase the nozzle rotation belt
tension.
1. Remove the extension spring from the frame bolt
to release the belt tension.
2. To increase the belt tension, move the extension
spring into the next chain link closer to the motor
mount.
3. Reinstall the extension spring onto the frame bolt.
Lubrication Locations
Lubrication is required at the following locations using
a lithium complex NLGI #2 grease.
Wipe the grease ttings clean before applying grease
to the grease ttings.
Refer to the maintenance schedule for service inter-
vals and the amount of grease.
1. Grease the drive shaft bearings from underneath
the frame. Grease the turbine shaft bearing. It
may be necessary to remove the inlet screen.

SERVICE
Service - 19
2. Grease the wheel axle bearing and the caster
wheel pivot.
3. Use a Teon type dry lubricant on the four nozzle
slides. This will both clean and lubricate the slides,
helping to ensure smooth operation of the nozzle.
Do not use a silicon lubricant.
Storage
Preparing the Attachment for Storage
1. Clean the attachment to remove accumulated
leaves, dirt, and other debris. Check for material
buildup in the inlet and discharge areas. Inspect
the turbine ns and the inside of the blower hous-
ing for dirt or debris buildup.
2. Inspect for loose or missing hardware, damaged
components, or signs of wear. Repair or replace
any damaged or worn components.
3. Inspect belts for signs of damage or wear and
replace as needed.
4. Inspect the safety decals. Replace any decals that
are faded, illegible, or missing.
5. Apply grease to all grease points and wipe o any
excess grease.
6. Lubricate the nozzle slides.
7. Inspect the hydraulic hoses for damage or wear.
Inspect the hydraulic hoses and ttings to ensure
tight, leak free connections.
8. Inspect the painted components for chips,
scratches, or rust. Clean and touch up the sur-
faces as needed.
Removing the Attachment from Storage
1. Clean the attachment to remove any accumulated
dust or debris.
2. Inspect the attachment as instructed in the Daily
Inspection section of this manual.
3. Test the attachment to ensure that all the compo-
nents are working properly.

SERVICE
Service - 20
Maintenance Schedule
# of locations # of pumps Daily At 50 hours At 100 hours At 150 hours At 200 hours At 250 hours At 300 hours At 350 hours At 400 hours At 450 hours At 500 hours At 550 hours At 600 hours At 650 hours At 700 hours At 750 hours At 800 hours At 850 hours At 900 hours At 950 hours At 1,000 hours Yearly
Grease and Lubrication: See Lubrication Section
Drive Shaft Bearing 2 1 üüüüüüüüüüüüüüüüüüüü
Turbine Shaft Bearing 1 1 üüüüüüüüüüüüüüüüüüüü
Caster Wheel Pivot 1 1 üüüüüüüüüüüüüüüüüüüü
Caster Wheel Bearing 1 ^ üüüüüüüüüüüüüüüüüüüü
Nozzle Slide (Teon dry lubricant) üüüüüüüüüüüüüüüüüüüü
Inspection
Inspect and Clean - Inlet and Discharge Areas,
Turbine Fins, and Blower Housing ü
Inspect for Loose, Missing, or Worn Components ü
Inspect the Belts and Pulleys ü
Inspect the Hydraulic Hoses and Fittings ü
Inspect the Safety Decals ü
^Grease until fresh grease is visible.
Maintenance Checklist
# of locations # of pumps Daily At 50 hours At 100 hours At 150 hours At 200 hours At 250 hours At 300 hours At 350 hours At 400 hours At 450 hours At 500 hours At 550 hours At 600 hours At 650 hours At 700 hours At 750 hours At 800 hours At 850 hours At 900 hours At 950 hours At 1,000 hours Yearly
Grease and Lubrication: See Lubrication Section
Drive Shaft Bearing 2 1
Turbine Shaft Bearing 1 1
Caster Wheel Pivot 1 1
Caster Wheel Bearing 1 ^
Nozzle Slide (Teon dry lubricant)
Inspection
Inspect and Clean - Inlet and Discharge Areas,
Turbine Fins, and Blower Housing
Inspect for Loose, Missing, or Worn Components
Inspect the Belts and Pulleys
Inspect the Hydraulic Hoses and Fittings
Inspect the Safety Decals
^Grease until fresh grease is visible.