Venturer STB7766G1 User manual

- 23 -
Instruction Manual
ATSC Converter Box
STB7766G1
Need More Help?
DO NOT RETURN THIS PRODUCT TO THE STORE
Please visit online help at
http//www.venturer.com
811-776691W032.indd 23811-776691W032.indd 23 12/18/2008 9:56:01 AM12/18/2008 9:56:01 AM

- 1 -
SAFETY PRECAUTIONS
The lightning flash with an arrowhead symbol, within the
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
cause an electric shock.
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within the equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in this
owner’s manual.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DO NOT
PLACE OBJECTS FILLED WITH LIQUIDS ON OR NEAR THIS UNIT.
Equipment tested for
compliance as a
complete unit
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules.These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diff erent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
811-776691W032.indd 1811-776691W032.indd 1 12/18/2008 9:55:48 AM12/18/2008 9:55:48 AM

- 2 -
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong.The wide blade or the third prong is provided for your safety.When the provided
plug does not fit into your AC power outlet, consult an electrician for replacement of the obsolete
outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
Portable Cart
Warning
13. Unplug this apparatus during lightning storms or when unused for long periods
of time.
14. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as the power-supply cord
or plug is damaged, liquid has spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture , does not operate normally,
or has been dropped.
811-776691W032.indd 2811-776691W032.indd 2 12/18/2008 9:55:49 AM12/18/2008 9:55:49 AM

- 3 -
ACCESSORIES
AC Adapter .............................................................................................................................. x 1
Remote Control ........................................................................................................................ x 1
AAA Batteries (for Remote Control) ......................................................................................... x 2
RF Cable .................................................................................................................................. x 1
CONTENTS
Safety Precautions ...................................... 1
Important Safety Instructions ..................... 2
Accessories ................................................. 3
Contents ....................................................... 3
Remote Control .................................................4
Quick Start Guide ........................................... 5-8
Control Reference Guide ............................. 9-10
Connections ................................................... 11
Connecting aTV(Using the RF Cable) .................11
ConnectingaTV(Using theAVCable)..................11
Power Supply ................................................. 12
Using the AC Adapter .........................................12
Turning on the Unit ..............................................12
Dolby Digital ......................................................12
Basic Operation .............................................. 13
Searching for Channels Automatically ................13
Viewing theTV Channel .....................................13
Adjusting theVolume ......................................... 13
Viewing the Information .....................................13
Viewing Signal ..................................................13
On-Screen Menu-Channel ....................... 14-15
Channel Scan/Add/ Edit .....................................14
Manual Scan .....................................................14
Output Channel .................................................15
On-Screen Menu-Option ........................... 15-17
Clock ................................................................ 15
Aspect Ratio ...................................................... 15
Language ......................................................... 16
Audio Language ................................................ 16
Caption Select .................................................. 16
DCC View .......................................................... 17
Power Save Mode ............................................ 17
Analog Audio ............................................ 17
On-Screen Menu-Lock ............................. 18-20
Lock System .....................................................18
Set Password .................................................... 18
Block Channel ...................................................18
TV Rating-Children ............................................19
TV Rating-General ........................................... 19
Movie Rating .....................................................20
Downloadable RRT ...........................................20
Maintenance ................................................... 21
Troubleshooting Guide ................................... 21
811-776691W032.indd 3811-776691W032.indd 3 12/18/2008 9:55:49 AM12/18/2008 9:55:49 AM

- 4 -
Battery Replacement
When the batteries become weak, the operating distance of the remote control is greatly reduced
and you will need to replace them.
To Install Batteries
2. Insert two AAA batteries.
• Point the remote control at the REMOTE SENSOR located on the unit.
• When there is a strong ambient light source, the performance of the infrared REMOTE SENSOR
may be degraded, causing unreliable operation.
• The recommended effective distance for remote operation is about 16 feet (5 meters).
1. Open the battery door.
REMOTE CONTROL
Notes:
• If the remote control is not going to be used for a long time, remove the batteries to avoid corrosion
damage caused by battery leakage.
• Do not mix old and new batteries. Do not mix ALKALINE, standard (CARBON-ZINC) or rechargeable
(NICKEL-CADMIUM) batteries.
• Always remove batteries as soon as they become weak.
• Weak batteries can leak and severely damage the remote control.
• WARNING: Do not dispose of batteries in a fire. Batteries may explode or leak.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same
or equivalent type.
811-776691W032.indd 4811-776691W032.indd 4 12/18/2008 9:55:49 AM12/18/2008 9:55:49 AM

- 5 -
1. Connect an antenna cable to the RF IN terminal on the rear of the unit.
2. Use the RF cable (included) to connect the unit and TV/Monitor.
3. Use the AC adapter (included) to connect a suitable wall outlet.The supplied 9V adapter operates
on AC 120V ~ 60Hz.
4. Turn on your TV and switch TV’s channel selection to Channel 3 .
Option Two: Using the AV Cable to Connect a TV
1. Connect an antenna cable to the RF IN terminal on the rear of the unit.
2. Use the AV Cable (not included) to connect the unit and TV/Monitor.
3. Use the AC adapter (included) to connect a suitable wall outlet.The supplied 9V adapter operates
on AC 120V ~ 60Hz.
4. Turn on your TV and follow the instructions included with it to select the “AV IN” function.
QUICK START GUIDE
Rear of TV
YELLOW
RED
WHITE
YELLOW RED WHITE
Rear of TV
Option One: Using the RF Cable to Connect a TV
STEP 1: CONNECTIONS
Warning: This system does not support cable TV.
When this converter box is powered on, digital signals from the ANTENNA RF IN jack are converted
to analog signals and output from the TV RF OUT jack or the VIDEO OUT jack.
When this converter box is in standby state, analog RF TV signals pass through the box and output
from the TV RF OUT jack.
Note:
• If a local TV Station happens to broadcast on Channel 3, we recommend you switch the unit’s
Output Channel to Channel 4 (and switch TV to Channel 4), following the instructions on Page 15.
811-776691W032.indd 5811-776691W032.indd 5 12/18/2008 9:55:49 AM12/18/2008 9:55:49 AM

- 6 -
STEP 2: TURNING ON THE UNIT
1. While the AC adapter is connected and the unit is on standby, power will be consumed and the
power indicator is RED.
2. Press the STANDBY/ON button to turn on the unit. The power indicator is GREEN.
1. Press the MENU button on the remote
control.
2. Use the / buttons to select the CHANNEL
menu.
3. Use the button to select Channel Scan and
press the ENTER button or the button to start
scanning.
STEP 5: VIEWING THE TV CHANNEL
1. Press the MENU button on the remote
control.
2. Use the / buttons to select the OPTION
menu.
3. Use the button to select Language then
press the ENTER button or the button.
4. Use the / buttons to select English /
Español (Spanish) / Français (French).
5. Press the EXIT button on the remote control to
exit menu.
STEP 3: SETTING THE OSD LANGUAGE
DCC View
Power Save Mode
Analog Audio
QUICK START GUIDE
Press the CH-/CH+ buttons to select a channel, or press the number button on the remote to select
the channel you want to watch.
• For channels 1 to 9, enter a one-digit channel number.
• For channels 10 to 69, enter the two-digit channel number.
Please read the Instruction Manual for further details on using the Converter Box.
STEP 4: SEARCHING FOR CHANNELS AUTOMATICALLY
811-776691W032.indd 6811-776691W032.indd 6 12/18/2008 9:55:50 AM12/18/2008 9:55:50 AM

- 7 -
QUICK START GUIDE
DISPLAY CONTENTS
When receiving a 16:9 digital broadcast signal, STB7766G1 Digital TV Converter will convert the
16:9 picture to fit a 4:3 TV screen. Enter Aspect Ratio Menu to select among four conversion
modes.
AUTO MODE (DEFAULT)
Displays all programs based on the aspect ratio of the program to 4:3 TV screen.
CROPPED MODE
This mode uses the entire screen of your TV, but the left and right end of the picture will be removed
on 4:3 TV screen.
Cropped
DCC View
Power Save Mode
Analog Audio
Auto
811-776691W032.indd 7811-776691W032.indd 7 12/18/2008 9:55:50 AM12/18/2008 9:55:50 AM

- 8 -
QUICK START GUIDE
Letter Box Mode
SQUEEZED MODE
The entire 16:9 picture will be displayed on your TV, but there will be unused areas (black bars) along
the top and bottom edges of your TV screen.
The entire 16:9 picture will be filled up your TV display but there will be distorted in the picture.
Letter Box
Squeezed
USING A 16:9 TV WITH THE DIGITAL TV CONVERTER
It is recommended that you use the Squeezed option to obtain the best picture format.
811-776691W032.indd 8811-776691W032.indd 8 12/18/2008 9:55:52 AM12/18/2008 9:55:52 AM

- 9 -
CONTROL REFERENCE GUIDE
Remote Control 1) MUTE Button
Press to turn off the sound.
2) MENU Button
Press to display the on-screen menu or switch
back to the previous menu screen.
3) CURSOR ( , , , ) Buttons
Use to highlight selections on a menu screen
and adjust certain settings.
ENTER Button
Confirm selection on a menu screen.
4) INFO Button
Press to display information on the current
channel.
5) VOL + / VOL - Button
Press to increase/decrease the volume.
6) CC Button
Press to change the Closed Caption
appearance. This function only works on
programs broadcasted with captions.
7) STANDBY/ON Button
Press to turn ON the unit or put it in STANDBY
(OFF) mode.
8) EXIT Button
Press to exit from the on-screen menu or a
pop-up display.
9) SIGNAL Button
Press to display TV signal quality.
10) CH / CH Buttons
Press to select the channel upward or
downward.
11) NUMERIC Buttons
Press to enter numbers or go directly to a
specific channel.
12) LAST CH
Press to switch repeatedly between the last
two channels displayed.
• [dot] Button
Press to enter digital sub-channels with the
numeric buttons (i.e. 11.3 or 12.7).
1
2
3
4
5
612
11
10
9
8
7
811-776691W032.indd 9811-776691W032.indd 9 12/18/2008 9:55:54 AM12/18/2008 9:55:54 AM

- 10 -
CONTROL REFERENCE GUIDE
1) Remote Sensor
Receives infrared signals from the remote
control.
2) CH-/CH+ Buttons
Press to select the channel upward or
downward.
3) Button
Turns the power on or restores the unit to
the standby mode.
4) STANDBY/ON Indicator
Green: power on
Red: standby mode
5) ANTENNA RF IN Terminal
Connect the AIR antenna.
6) TV RF OUT Terminal
Use to connect yourTV using a coaxial cable.
When this Conventer Box is powered on,
analog RF signals output from the TV RF
OUT terminal.
When this Conventer Box is in standby state,
analog RF TV signals pass through the box
and output from the TV RF OUT terminal.
7) AUDIO OUT / VIDEO OUT Jacks
Outputs audio/video signals to a connected
TV.
8) DC IN 9V Jack
Connect the supplied AC adapter.
Front View
Back View
1234
567 8
811-776691W032.indd 10811-776691W032.indd 10 12/18/2008 9:55:54 AM12/18/2008 9:55:54 AM

- 11 -
CONNECTIONS
Connecting a TV (Using the RF Cable)
1. Connect an antenna cable to the RF IN terminal on the rear of the unit.
2. Use the RF cable (included) to connect the unit and TV/Monitor as shown.
3. Turn on your TV and switch TV’s channel selection to Channel 3.
When this converter box is powered on, digital signals from the ANTENNA RF IN jack are converted
to analog signals and output from the TV RF OUT jack or the VIDEO OUT jack.
When this converter box is in standby state, analog RF TV signals pass through the box and output
from the TV RF OUT jack.
Connecting a TV (Using the AV Cable)
1. Connect an antenna cable to the RF IN terminal on the rear of the unit.
2. Use the AV Cable (not included) to connect the unit and TV/Monitor as shown.
Rear of TV
Note:
• If a local TV Station happens to broadcast on Channel 3, we recommend you switch the unit’s
Output Channel to Channel 4 (and switch TV to Channel 4), following the instructions on Page 15.
YELLOW RED WHITE
YELLOW RED WHITE
Rear of TV
Note:
Make sure to turn on your TV and follow the instructions included with it to select the “AV IN”
function.
Warning: This system does not support cable TV.
811-776691W032.indd 11811-776691W032.indd 11 12/18/2008 9:55:55 AM12/18/2008 9:55:55 AM

- 12 -
Using the AC Adapter
The supplied 9V adapter operates on AC 120V ~ 60Hz.
While the AC adapter is connected and the unit is on standby, power will be consumed and the power
indicator is RED.
Cautions:
• The AC adapter included with this unit is for its use only. Do not use it with other equipment.
• When the unit is not going to be used for a long period of time, disconnect the AC adapter from
the AC power outlet.
• When the AC adapter is plugged in, the apparatus is not completely disconnected from the main
power supply, even when the power is turned off.
POWER SUPPLY
Turning on the Unit
Press the STANDBY/ON button to turn on the unit. The power indicator is GREEN.
Dolby Digital
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.
811-776691W032.indd 12811-776691W032.indd 12 12/18/2008 9:55:55 AM12/18/2008 9:55:55 AM

- 13 -
BASIC OPERATION
Adjusting the Volume
You can control the volume using the buttons on the remote control.
VOL-/VOL+ Buttons
Use these buttons to increase or decrease the volume.
MUTE Button
This button is used to mute the sound of the unit. No audio will be heard once this button is
pressed.
To cancel the mute action, press the MUTE button again.
Viewing the Information
You can view information for the current TV program by pressing the INFO button on the remote
control.
The INFO shows:
• The major channel number and the minor channel number if you are viewing a digital channel
• Current time and date
• Program title and other information if available
• The current program’s rating
• Broadcast format of current program
• Multilingual
• Caption
To hide INFO:
Press the INFO button again or press the EXIT button.
Viewing Signal
To view the signal quality, press the SIGNAL button on the remote control. A beep sound will be
heard.
1. Press the MENU button on the remote control.
2. Use the / buttons to select the CHANNEL menu.
3. Use the button to select Channel Scan and press
the ENTER button or the button to start scanning.
Searching for Channels Automatically
Notes:
• The unit MUST be connected to an antenna in order
to receive digital TV signals.
• If you wish to stop scanning in the middle of the
scanning process, press the ENTER button.
Viewing the TV Channel
Viewing a television station after searching for channels.
Press the CH / CH buttons to select a channel, or press the number button on the remote to
select the channel you want to watch.
• For channels 1 to 9, enter a one-digit channel number.
• For channels 10 to 69, enter the two-digit channel number.
811-776691W032.indd 13811-776691W032.indd 13 12/18/2008 9:55:55 AM12/18/2008 9:55:55 AM

- 14 -
Channel Edit
1. Press the MENU button on the remote control.
2. Use the / buttons to select the CHANNEL menu.
3. Use the button to select Channel Edit then press
the ENTER button or the button.
4. Use the / buttons to select the channel number
then press the ENTER button.
ON-SCREEN MENU - CHANNEL
Manual Scan
In the case of Terrestrial TV with an indoor/outdoor antenna, Channel Scan may not find all existing
channels because a certain channel may require the antenna to be adjusted to different orientation.
You can add such a channel by entering the channel number manually.
1. Press the MENU button on the remote control.
2. Use the / buttons to select the CHANNEL menu.
3. Use the button to select Manual Scan then press
the ENTER button or the button.
4. Use the / buttons to select the channel number
then press the ENTER button.
Use the menu configuration to set detailed options for each function. Press the MENU button on the
remote control to open the menu screen.
• To return to the previous menu press the MENU button on the remote control.
• To exit the menu screen press the EXIT button on the remote control.
Channel Scan
See “Searching for Channels Automatically” for details.
Channel Add
1. Press the MENU button on the remote control.
2. Use the / buttons to select the CHANNEL menu.
3. Use the button to select Channel Add then press
the ENTER button or the button.
Note: Valid channels which are already stored before
you use Channel Add will be skipped during the
channel scan process.
811-776691W032.indd 14811-776691W032.indd 14 12/18/2008 9:55:56 AM12/18/2008 9:55:56 AM

- 15 -
ON-SCREEN MENU - OPTION
Clock
1. Press the MENU button on the remote control.
2. Use the / buttons to select the OPTION menu.
3. Use the button to select Clock then press the
ENTER button or the button.
4. Press the / buttons to select the Time Zone
(Eastern/Central/Mountain/Pacific/Alaska/Hawaii/
New F.land/Atlantic).
Aspect Ratio
1. Press the MENU button on the remote control.
2. Use the / buttons to select the OPTION menu.
3. Use the button to select Aspect Ratio then press
the ENTER button or the button.
4. Use the / buttons to select the options (Auto/Letter
Box/Cropped/Squeezed).
Auto: Displays all programs based on the aspect ratio of the program.
Letter Box: Displays all programs in 16:9 aspect ratio.
Cropped: No change on the ratio, but the picture is cropped.
Squeezed: All programs are displayed to fit on the screen.
DCC View
Power Save Mode
Analog Audio
DCC View
Auto
Power Save Mode
Analog Audio
ON-SCREEN MENU - CHANNEL
Output Channel
You can select NTSC RF output channel.
1. Press the MENU button on the remote control.
2. Use the / buttons to select the CHANNEL menu.
3. Use the button to select Output Channel then press
the ENTER button or the button.
4. Use the / buttons to select the channel number.
ON-SCREEN MENU - OPTION
811-776691W032.indd 15811-776691W032.indd 15 12/18/2008 9:55:56 AM12/18/2008 9:55:56 AM

- 16 -
ON-SCREEN MENU - OPTION
1. Press the MENU button on the remote control.
2. Use the / buttons to select the OPTION menu.
3. Use the button to select Caption Select then press
the ENTER button or the button.
4. Use the / buttons to select the options
(ACC/DCC/DCC Service). “ACC” is Analog TV Closed
Caption. “DCC” is Digital TV Closed Caption.
5. Use the / buttons to make adjustments.
Caption Select
Notes:
• If DCC (Digital Closed Caption) is set to Custom, DCC View is activated.
• Caption is essential for a hearing-impaired person.
• If both ACC (Analog Closed Caption) and DCC are on service and both settings are ON, only
DCC is displayed.
• ACC is available only when DCC is OFF.
Power Save Mode
DCC View
Analog Audio
Standard: Use the default digital caption style from broadcaster.
Custom: Activate the DCC View item and set your desired font settings.
1. Press the MENU button on the remote control.
2. Use the / buttons to select the OPTION menu.
3. Use the button to select Audio Language then
press the ENTER button or the button.
4. Use the / buttons to select the audio language
(English / Spanish / French).
Audio Language
When you change the channel on Digital TV, you may be able to listen to the audio in an alternate
language by selecting the appropriate language option. If there is no selected audio language,
the primary audio signal transmitted by the TV broadcaster is selected automatically.
DCC View
Power Save Mode
Analog Audio
1. Press the MENU button on the remote control.
2. Use the / buttons to select the OPTION menu.
3. Use the button to select Language then press the
ENTER button or the button.
4. Use the / buttons to select English / Español
(Spanish) / Français (French).
Language
DCC View
Power Save Mode
Analog Audio
Note: Not all TV channels broadcast with multiple languages.
811-776691W032.indd 16811-776691W032.indd 16 12/18/2008 9:55:57 AM12/18/2008 9:55:57 AM

- 17 -
ON-SCREEN MENU - OPTION
DCC View
1. Press the MENU button on the remote control.
2. Use the / buttons to select the OPTION menu.
3. Use the button to select DCC View then press the
ENTER button or the button.
4. Use the / buttons to select the options, then use
the / buttons to make adjustments.
Use this to set the character font. Only DCC (Digital Closed Caption) is set to Custom, DCC View
is activated.
Power Save Mode
Analog Audio
1. Press the MENU button on the remote control.
2. Use the / buttons to select the OPTION menu.
3. Use the button to select Power Save Mode then
press the ENTER button or the button.
4. Use the / buttons to select the options
(Off / 1 hour / 2 hours / 4 hours / 8 hours).
1. Press the MENU button on the remote control.
2. Use the / buttons to select the OPTION menu.
3. Use the button to select Analog Audio then press
the ENTER button or the button.
4. Use the / buttons to select the analog audio
(Mono / Stereo).
Power Save Mode is the function to automatically switch
from the ON state to the Sleep state after a period of time
without user input.
Note:
• This product is currently set to Power Save Mode. It will not receiveTV signal after 4 hours of inactivity.
DCC View
Power Save Mode
Standard
Analog Audio
DCC View
Power Save Mode
Analog Audio
Note:
• To activate DCC View, DCC on Caption Select should
be set to ‘Custom’.
Mono: Select Mono if you watch TV by TV RF OUT
terminal.
Stereo: Select Stereo if you watch TV by VIDEO OUT
terminal.
DCC View
Power Save Mode
Analog Audio
Stereo
Mono
811-776691W032.indd 17811-776691W032.indd 17 12/18/2008 9:55:58 AM12/18/2008 9:55:58 AM

- 18 -
ON-SCREEN MENU - LOCK
1. Press the MENU button on the remote control.
2. Use the / buttons to select the LOCK menu.
3. Use the / buttons to select Set Password then
press the ENTER button or the button.
4. Enter values (4 digit) for new password and again to
confirm password.
Set Password
RRT
1. Press the MENU button on the remote control.
2. Use the / buttons to select the LOCK menu.
3. Use the / buttons to select Block Channel then
press the ENTER button or the button.
4. Use the / buttons to select Antenna Channel then
press the ENTER button.
Block Channel
RRT
Notes:
• Remember your password if you have changed it.
• If you forget the password,enter “8888” to unlock parental control.
1. Press the MENU button on the remote control.
2. Use the / buttons to select the LOCK menu.
3. Use the button to position the cursor on the input field and enter password. If you have not
specified the password, input the factory-default code, “0000”.
4. Use the / buttons to select Lock System then press the ENTER button or the button.
5. Use the / buttons to select On/Off.
Lock System
RRT
RRT
811-776691W032.indd 18811-776691W032.indd 18 12/18/2008 9:55:59 AM12/18/2008 9:55:59 AM

- 19 -
1. Press the MENU button on the remote control.
2. Use the / buttons to select the LOCK menu.
3. Use the / buttons to select TV Rating-General
then press the ENTER button or the button.
4. Use the / buttons to select the options (Age /
Dialogue / Language / Sex / Violence) then press
the ENTER button or the button.
5. Use the / buttons to block/unblock rating. If
Blocking is set to ON, a lock icon is indicated.
TV Rating-General
TV Rating-General is for classifying the age level of TV programs by the general criterion.
• Age restriction has higher priority than the others.
RRT
1. Press the MENU button on the remote control.
2. Use the / buttons to select the LOCK menu.
3. Use the / buttons to select TV Rating-Children
then press the ENTER button or the button.
4. Use the / buttons to select Age or Fantasy
Violence then press the ENTER button or the
button.
5. Use the / buttons to block/unblock rating. If
Blocking is set to ON, a lock icon is indicated.
TV Rating-Children
TV Rating-Children is for classifying the age level of TV programs for children.
• Age restriction has higher priority than the others (Fantasy Violence).
RRT
ON-SCREEN MENU - LOCK
The lock levels are equivalent to the following ratings.
TV-Y: All children.
TV-Y7: Children 7 years and older.
TV-G: General Audience.
TV-PG: Parental guidance suggested.
TV-14: Parents strongly cautioned.
TV-MA: Mature audience only.
811-776691W032.indd 19811-776691W032.indd 19 12/18/2008 9:56:00 AM12/18/2008 9:56:00 AM