Veracity LONGSPAN VLS-1P-B User manual

POWER INPUT
|The Base unit (VLS-1P-B) may be
powered by either POE-in or by an
external Veracity 57V DC power supply
(VPSU-57V-800).
|POE-in is provided by a POE network
switch or by a POE injector.
|When using the external 57V DC PSU,
it is essential to observe the correct
polarity on the green 2-pin screw
LONG RANGE ETHERNET & POE
Surge Protection
All Veracity products have been independently tested to verify their
resilience to the stringent immunity levels of international standards.
Users should note that no electronic equipment can be guaranteed
to be completely protected at levels beyond the defined standard ;
therefore product warranty cannot include damage to products
which has been caused by surges exceeding those of the standards
specified, for example lightning strike activity.
It is the user’s responsibility to implement relevant surge protection
measures, as appropriate to the installation. This may include the
fitting of additional surge protection devices where required.
©Veracity UK Ltd 2019
QSG WV1.5EN
LONGSPAN is a trademark of Veracity UK Ltd
This Device Complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
LONGSPAN
|LONGSPAN can deliver an unrestricted
full-duplex 100Base-TX connection
over 820m of Cat6 or over 600m of
Cat5e network cable.
On Cat6 cable, 25W of POE can be
delivered at 600m or 15W at 800m.
A 10Base-T connection can be
achieved up to 1050m on Cat6.
See LONGSPAN datasheet for details.
|LONGSPAN is fully self-configuring,
featuring remote diagnostic LEDs and
extended temperature rating -40ºC to 70ºC.
VLS-1P-B, VLS-1P-C
QUICK START GUIDE
LONG RANGE ETHERNET & POE
POE POWER BUDGET
|The Veracity 57V DC PSU will provide
maximum range and POE power
budget at the camera end.
|POE-in is not applicable as a power
source when higher-power POE cameras
are installed, i.e. 802.3at (POE Plus)
25 watt devices. In these cases, the
Veracity 57V DC PSU should be used.
INSTALLATION NOTES
|Standard Cat5e or Cat6 cable and
RJ45 connectors should be used.
|LONGSPAN supports both patch and
crossover cables. Patch wiring (straight
through connection) is recommended.
|LONGSPAN extended network link
set-up and configuration is fully automatic.
|LONGSPAN Ethernet ports should be
connected to 100Base-TX or 10Base-T
Ethernet compatible equipment.
|LONGSPAN extended network ports
should only be connected to other
LONGSPAN extended network ports.
Devices are always used in pairs.
|VLS-1P-B supports POE-in (unless
powered externally). VLS-1P-C supports
POE out (to compatible devices).
SURGE PROTECTION
|Any LONGSPAN network design
for outdoor or external sections
must incorporate the appropriate level
of surge protection to avoid invalidation of
warranty due to electrical storm damage.
It is the responsibility of the system
installer to ensure the correct level of
surge protection.
See also surge protection statement below
and LONGSPAN Application Notes.
terminal connector. The correct polarity
is shown on the product top label.
Note that LONGSPAN will automatically
disable the POE-in function when an
external PSU is connected.
|Optionally, the Veracity 57V DC PSU
may be used to locally power LONGSPAN
at the Camera end in order to provide
maximum POE Plus power output to
the camera whatever the LONGSPAN
connection distance.
LARGER SYSTEMS
|For high channel count or high-density
applications, LONGSPAN Base units
may be rack-mounted in the VLS-1U
fascia plate to support up to 24 units
in 1U. (See LONGSPAN datasheet).
|Veracity 57V DC rackmount power
supplies are available for larger installations
with multiple base devices.
|LONGSPAN may also be used with
other twisted pair cables* as follows:
4-pair cable: 10Base-T /100Base-TX with
POE with standard Cat5e / Cat6 pin-out.
2-pair cable: 100Base-TX performance
can be achieved with POE on 2 pairs,
where pins 1 & 2 are used for data and
pins 7 & 8 are used for POE.
1-pair cable: 10Base-T/100Base-TX
performance can be achieved on 1pair,
where pins 1 & 2 are not crossed-over.
|When connecting LONGSPAN on cables
over 600m or over cables with four or
more joins (couplers, outlets, patch
panels) on-site testing is recommended.
*Stated performance will be achieved where
twists/metre and cable length permits,
otherwise LONGSPAN will default to
10Base-T performance.
|Please refer to your regional Veracity
Technical Support team for help & advice.
See Application Notes for more details on
www.veracityglobal.com
POWER OVER ETHERNET 1 2 3 SURGE PROTECTION DEVICES RECOMMENDED FOR LONG OUTDOOR NETWORKS
POE NETWORK
SWITCH
POE
POWER
UP to 25W POE
(OPTIONAL)
POWER
SUPPLY
820M ON CAT6
VLS-1P-CVLS-1P-B
IP
CAMERA
123

|For extremely long runs, it may take a
few seconds to optimise the link.
|For more detailed connection information
please refer to the current LONGSPAN
datasheet on www.veracityglobal.com
5 10 15 20 25
Green LEDs show POE power available for
camera (or other POE-compliant device) in watts.
The power level is displayed after the camera
side unit has powered up.
5 10 15 20 25
Overload Short-circuit Signature High-temp
Overload Short-circuit Signature High-temp
Wiring Equipment
|The tables below show the Ethernet and
LONGSPAN interface ports LED status
on both Base and Camera devices.
|The green LONGSPAN LED may blink
quickly while connecting.
ETHERNET AND LONGSPAN LEDS
SAFEVIEW ™ GREEN POE STATUS LEDS
Green
LED
ETHERNET LEDS FUNCTION
RJ45 Green Power
On Power Good
RJ45 Yellow Link / Activity
On Link Established
Flash Network Activity
In normal operation, the SAFEVIEW™ LEDs
display power available in flashing or steady green.
ON = POE enabled to camera.
FLASH = POE available but not enabled, no
compliant device detected.
Consider fitting a Veracity 57V DC power supply
if the power displayed is less than your camera
requires.
SAFEVIEW ™ RED ERROR CODE LEDS
If LONGSPAN detects an error or fault, a
diagnostic code will flash red on SAFEVIEW™
POE power draw has exceeded limit.
Power source must be upgraded.
Voltage too low, POE disabled. Check voltage
and polarity of power supply.
POE to camera refused or disconnected due to
error as indicated.
POE over LONGSPAN refused or disconnected
due to error as indicated.
POE over LONGSPAN enabled but no link.
Check cable length, wiring, and equipment.
Cable wiring error / inferior equipment detected,
connection refused.
LONGSPAN LEDS FUNCTION
RJ45 Green Power
On 100Mbps
Flash 10Mbps
Blink No link
RJ45 Yellow Link / Activity
On Link Established
Flash Network Activity
Yellow
LED
Green
LED
Yellow
LED
SAFEVIEW ™ LEDS
|SAFEVIEW™ warning and error codes
are very rarely displayed in typical
installations.
|However, they can assist you to quickly
resolve any installation issues that may
occasionally arise.
LONGSPAN DIMENSIONS
36mm
23mm
111mm
Ø5mm
100mm
96mm
120mm
|The maximum POE power available for
connected devices is detected and
displayed automatically.
|SAFEVIEW™ LEDs display status and
diagnostic information for both the local
and remote unit.
+_
BASE CAMERA BASE CAMERA
+_
+_