Veripos ld7 User manual

VERIPOS LD7 Quick guide
VOSS: http://help.veripos.com
AB-V-MA-00560 Rev A8
Reference card for use day to day, to print and use.
1.
Latch Power Button
2.
Status LEDs
3.
Main Antenna Connector
4.
Aux Antenna Connector
5.
1 PPS /Event Connector
6.
Com 1 Connector
7.
Power Connector
8.
Ethernet / USB Connector
9.
Com2 / Com3 Connector
10.
Com4 / Com5 Connector
Cables and adaptors supplied
Antennas
See LD7 Installation manual for more information.
Connecting LD7
Connect the LD7 making connections as shown in the typical example
installation below.
When installing the Lemo connectors ensure the red dot on the plug
and red mark on the socket line up
Initial start-up
Press the power switch on the front panel. Allow the unit approximately
120 seconds to start up.
Use a Windows 7 or XP PC with browser software (preferably Google
Chrome version 30.0.1559.101 or above)
Amend the IP address of the PC to a compatible address for the LD7.
The default fixed IP address of the LD7 is 192.168.0.126.
Connect the LD7 RJ45 lead via an Ethernet hub or directly to the PC.
On the PC, open internet browser and enter the default LD7 IP address,
192.168.0.126
Enter the unique LD7 User code on front of LD7 unit and press OK.
Once connected the main browser page is shown:
LD7 Main browser page –default / recommended settings shown
Beam selection
On the LBand page select a Veripos correction satellite beam for your
1 x PSU
4 pin Lemo Plug
1 x Ethernet / USB Cable
16 pin Lemo Plug
(PN 10119)
1 x PPS / Event Cable
7 pin Lemo Plug
(PN 10122)
1 x Com1 Cable
9 pin Lemo Plug
(PN 10120)
1 x Com2 / Com3 Cable
14 pin Lemo Plug
(PN 10121)
1 x Com4 / Com5 Cable
10 pin Lemo Plug
1 x AC power lead
4 x LMR240 coaxial cable
TNC Plug to N-Type Plug
(PN: VI-C-0012)
2 x LMR400 coaxial cable
N-Type Skt to N-Type Skt
(PN: VI-C-0030)
1 x LMR240 coaxial cable
N-Type Plug to N-Type
Plug
(PN: VI-C-0011)
1 x LMR240 coaxial cable
TNC Plug to N-Type Plug
(PN: VI-C-0012)
1 x LMR400 coaxial cable
N-Type Skt to N-Type Skt
(PN: VI-C-0030)
2 x LBand & GNSS combined
V460
Dedicated LBand (optional)
V86

VERIPOS LD7 Quick guide
VOSS: http://help.veripos.com
AB-V-MA-00560 Rev A8
vessel work area from the drop down options and click Apply:
Upon lock to the selected beam the Sync LED should be green.
NOTE
In most locations, more than one beam will be available. Different
beams carry corrections for different reference stations. A beam should
be selected which has the highest elevations and reference stations most
suited to the work area.
Enabling the LD7 for Veripos Services
Contact the Veripos Helpdesk to request a service enable quoting
your Unit ID, Service Access Licence (SAL) number and listing
services required e.g. Veripos Ultra with Standard.
Download a Service Notification Form from http://help.veripos.com
and use this when contacting the Veripos Helpdesk for an enable.
Tel. [phone] email: [e-mail]
NOTE
The sync indicator must be green in order for the Access code to be
received.
When the unit is enabled the ENB LED should be Green
Configuring data outputs from the LD7
Position and heading data (NMEAa or NMEAb) can be output on
Com ports 1 or 2 or via LAN from the LD7.
On the Web Browser go to the GNSS Tab and set the NMEA
Messages required for output.
For serial output, go to the LD7 I/O page and select the data streams
and baud rate required for Com ports 1 and 2.
Configuring data outputs from the LD7 (LAN)
Position and heading data (NMEAa or NMEAb) is also available for
output via LAN.
To output NMEA messages from the LD7, the IP address of the GNSS
receiver should be used. Note that this is different from the IP address
used to connect to the LD7 WebUI.
Data stream
IP Address
Port No.
NMEAa
GNSS Rx IP Address
(192.168.0.127 default)
9011
NMEAb
GNSS Rx IP Address
(192.168.0.127 default)
9012
LD7 with Verify QC –LAN outputs
Configure the Verify QC PC network settings to an applicable IP address
and Subnet Mask for use with the LD7 (Control Panel/Network
Connections).
NOTE
The LD7 processor, GNSS and LBand receivers all have separate IP
addresses. Take into account when setting an IP address on the PC.
To determine or set the LD7, LBand and GNSS Rx IP Addresses use the
LD7 Web Browser.
Configure Verify QC inputs for Client Sockets with the following IP
Address and LAN ports;
LD7 with Verify QC - Serial Port outputs
You can view or amend baud rates, etc. by going to LD7 IO page in the
Web Interface.
NOTE
Baud Rates are user configurable. As a result users should check the Baud
Rate Settings using the LD7 Web Interface (see Configuring data outputs
section of this quick guide).
Beam
Coverage
143.5E
Asia, Australasia, Indian Ocean
POR
East Asia, Australasia, Alaska
IOR
Asia, Indian Ocean, East Africa, Persian Gulf,
Caspian Sea
25E
North Sea, Mediterranean Sea, Africa, Persian
Gulf, Caspian Sea
AORW
North America, Gulf of Mexico, South America
98W
North America, Gulf of Mexico, South America
AORE
North Sea, Mediterranean Sea, Africa
LD7 LAN Port mapping
Data stream
IP Address
Port
No
Verify QC IP
GNSS Raw
GNSS Rx IP Address
9013
GNSS Rx
RTCMa
LBand IP Address
9001
RTCM
LBand Config
LBand IP Address
9003
Demodulator Status
Default COM port settings
LD7 COM
port No.
Source /Baud
Content
Verify QC IP
COM3
GNSS / 115200
GNSS Raw
GNSS Rx
COM4
LBand / 115200
RTCMa
RTCM
COM 5
LBand / 115200
RTCMb
RTCM