Vermont Castings DEB20 User manual
Installation and
Operating Instructions
44D0060 1/13 Rev. 12
440060
DEB cover
DEB Unvented Gas Logs
244D0060
Codes ......................................................................4
Gas Specications ..................................................5
Gas Pressures ........................................................5
Ignition Controls ......................................................5
Pilot .........................................................................5
Thermal Generator ..................................................5
Installing Vented Applications ............................... 11
Damper Stop Installation ....................................... 11
Place and Secure Appliance ................................. 11
Assembly Procedure .............................................12
Manual Control ......................................................13
Millivolt/Thermostat Control ..................................13
Connect Wall Switch or Thermostat ......................14
Connect Remote Receiver ....................................15
Install Thermostat Sensor .....................................15
Operation of Thermostat Sensor ...........................17
Check System Operation ......................................17
Millivolt/Thermostat Control ..................................20
Manual Control ......................................................20
Burner Flame Appearance ....................................21
For Your Safety Read Before Lighting ..................23
Manual Control .....................................................24
Millivolt/Thermostat Control .................................25
To Turn Off Gas to Heater .....................................25
Match Lighting Instructions ...................................26
Burner Assembly ...................................................29
Accessories ...........................................................30
Logs ......................................................................31
DEB Unvented Gas Logs
44D0060 3
Please leave these instructions with the appliance.
Please retain these instructions for future reference
.
1. Due to high temperatures, the appliance should be
located out of trafc and away from furniture and
draperies.
2. Children and adults should be alerted to the hazard
of high surface temperature and should stay away
to avoid burns or clothing ignition.
3. Young children should be carefully supervised when
they are in the same room with the appliance.
4. Do not place clothing or other ammable material
on or near the appliance.
5. Any safety screen or guard removed for servicing
an appliance, must be replaced prior to operating
the heater.
6. Installation and repair should be done by a qualied
service person.
7. To prevent malfunction and/or sooting, an unvented
gas heater should be cleaned before use and at
least annually by a professional service person.
More frequent cleaning may be required due to
excessive lint from carpeting, bedding material, etc.
It is imperative that control compartments, burners
and circulating air passageways be kept clean.
12. Correct installation of the ceramic ber logs, proper
location of the heater, and annual cleaning are neces-
sary to avoid potential problems with sooting. Sooting,
resulting from improper installation or operation, can
settle on surfaces outside the replace. See log place-
ment instructions for proper installation.
13. Avoid any drafts that alter burner ame patterns. Do not
allow fans to blow directly into replace. Do not place
a blower inside burn area of rebox. Ceiling fans may
create drafts that alter burner ame patterns. Sooting
and improper burning will occur.
14. : Candles, incense, oil lamps, etc. produce
combustion byproducts including soot. Vent-free appli-
ances will not lter or clean soot produced by these
types of products. In addition, the smoke and/or aro-
matics (scents) may be reburnt in the vent-free appli-
ance which can produce odors. It is recommended to
minimize the use of candles, incense, etc. while the
vent-free appliance is in operation.
15. This is an unvented gas-fired heater. It uses air
(oxygen) from the room in which it is installed. Provi-
sions for adequate combustion and ventilation air must
be provided. Refer to Page 6.
16. This heater shall not be installed in a room or space
unless the required volume of indoor combustion air is
provided by the method described in the National Fuel
Gas Code, ANSI Z223.1/NFPA 54, the International
Fuel Gas Code or applicable local codes.
17. Keep room area clear and free from combustible
materials, gasoline and other ammable vapors and
liquids.
18. Unvented gas heaters are a supplemental zone heater.
They are not intended to be the primary heating appli-
ance.
19. Unvented gas heaters emit moisture into the living
area. In most homes of average construction, this
does not pose a problem. In houses of extremely
tight construction, additional mechanical ventilation is
recommended.
20. During manufacturing, fabricating and shipping, various
components of this appliance are treated with certain
oils, lms or bonding agents. These chemicals are not
8. Early signs of
carbon monoxide poisoning are similar to the u with
headaches, dizziness and/or nausea. If you have these
signs, obtain fresh air immediately. Have the heater
serviced as it may not be operating properly.
9. The installation must conform with local codes or, in
the absence of local codes, with the National Fuel Gas
Code, ANSI Z223.l/NFPA54.
10. This unit complies with the latest edition of ANSI
Z21.11.2 Unvented Heaters and also complies with
ANSI Z21.60 / CSA 2.26 Decorative Vented Appliances
for Solid Fuel Burning Fireplaces. State and local
codes may only allow operation of this appliance in a
vented conguration. Check your state or local codes.
For vented operation, see “Vented Instructions” in this
manual.
11. Do not install the heaters in a bathroom or bedroom.
DEB Unvented Gas Logs
444D0060
harmful but may produce annoying smoke and smells
as they are burned off during the initial operation of the
appliance; possibly causing headaches or eye or lung
irritation. This is a normal and temporary occurrence.
The initial break-in operation should last two to three
hours with the burner at the highest setting. Provide
maximum ventilation by opening windows or doors to
allow odors to dissipate. Any odors remaining after this
initial break-in period will be slight and will disappear
with continued use.
21. Input ratings are shown in BTU per hour and are for
elevations up to 2,000 feet. For elevations above 2,000
feet, input ratings should be reduced 4 percent for each
1,000 feet above sea level. Refer to the National Fuel
Gas Code.
22. The appliance and its appliance main gas valve must
be disconnected from the gas supply piping system
during any pressure testing of that system at test pres-
sures in excess of 1/2 psig (3.5 kPa).
23. The appliance must be isolated from the gas supply
piping system by closing its equipment shutoff valve
during any pressure testing of the gas supply piping
system at test pressures equal to or less than 1/2 psig
(3.5 kPa).
24. Do not use this room heater if any part has been under
water. Immediately call a qualied service technician
to inspect the room heater and to replace any part of
the control system and any gas control which has been
under water.
25. This appliance must not be used with glass doors in
the closed position. This can lead to pilot outages and
severe sooting outside the replace.
26. Never burn solid fuels in a replace where a unvented
room heater is installed.
27. Always have a replace screen in place when the
appliance is in operation and, unless other provisions
for combustion air are provided, the screen must have
an opening(s) for induction of combustion air.
Nous recommandons que nos
appareils de chauffage au gaz
soient installés et entretenus par
des professionnels qui ont été
accrédités aux È.U. par le National
Fireplace Institute ® (NFI) comme
étant des spécialistes du NFI en
matièred’appareils de chauffage
au gaz.
Adhere to all local codes or, in their absence, the latest
edition of THE NATIONAL FUEL GAS CODE ANSI Z223.1
or NFPA54 which can be obtained from…
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
or
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
DEB Unvented Gas Logs
44D0060 5
Natural Propane (LP)
Manual Regulator Pressure 3.0” w.c. 10.0” w.c.
Millivolt Regulator Pressure 3.5” w.c. 10.0” w.c.
Millivolt Pilot Regulator 3.5” w.c. n/a
Max. Gas Inlet Pressure 10.5” w.c. 13.0” w.c.
Min. Gas Inlet Pressure 5.0" w.c. 11.0" w.c.
DEB20NM Nat. Manual 18,000 28,000
DEB20PM LP Manual 18,000 28,000
DEB24NM Nat. Manual 20,000 38,000
DEB24PM LP Manual 20,000 38,000
DEB30NM Nat. Manual 20,000 38,000
DEB30PM LP Manual 20,000 38,000
DEB20NV Nat. Millivolt 18,000 28,000
DEB20PV LP Millivolt 20,000 28,000
DEB24NV Nat. Millivolt 25,000 38,000
DEB24PV LP Millivolt 30,000 38,000
DEB30NV Nat. Millivolt 25,000 38,000
DEB30PV LP Millivolt 30,000 38,000
An external regulator is required to reduce supply
pressure to a maximum of 10.5" w.c. on Natural Gas sys-
tems operating at higher pressure.
An external regulator is required to reduce supply
pressure to a maximum of 13.0" w.c. for LP systems.
Piezo ignitor allows ignition of the pilot without the
use of matches or batteries.
- All gas to the gas logs is shut off at
the valve.
- Valve position to light/maintain a
standing pilot.
- Variable position corresponding to
desired ame height.
- All gas to the gas logs is shut off at
the valve.
- Valve position to light/maintain a
standing pilot.
- Valve position to turn ON/OFF log
set with remote switch/thermostat.
- Variable position to control ame
height (heat output).
The gas log heater is tted with a specially designed
safety pilot (ODS assembly) which senses the amount
of oxygen available in the room and shuts the gas log
heater off if the oxygen level begins to drop below
a satisfactory level. The pilot can only be relit when
adequate fresh air is available.
The millivolt gas log pilot is tted with a millivolt
(thermopile) generator to provide power for remote
activation.
DEB Unvented Gas Logs
644D0060
Check your packing list to verify that all listed parts have
been received. You should have the following:
• Unvented gas log grate/burner assembly
• Two (2) plastic bags containing crushed volcanic
rock
• Installation/operating instructions
• Two (2) anchoring screws
• Ceramic ber logs
The millivolt controlled version of this heater is the only
style designed to be operated with optional devices for
ON/OFF functions. The following options may be used
with the millivolt controlled heater. These options are not
packaged with the log set.
• Hand held Remote with receiver
• Wall thermostat with 15' wire
• Wall switch with 15' wire
• Hand held Thermostat Remote with receiver
• Thermostat sensor
Carefully inspect the contents for shipping damage. If any
parts are missing or damaged, immediately inform the
dealer from whom you purchased the appliance.
You should have the following items available before pro-
ceeding with installation:
• External regulator (for propane/LPG and 1/2 lb.
natural gas systems only)
• Piping which complies with local codes
• Sediment trap (recommended)
• Screwdriver
• Tee joint.
• Pipe sealant approved for use with propane/LPG
(Resistant to sulfur compounds)
• Drill with 5/32 bit
• Pipe wrench or appropriate size crescent wrench
set
• Manual shutoff valve
National
Fuel Gas Code, ANSI Z223.1/NFPA 54
International Fuel Gas Code
DEB Unvented Gas Logs
44D0060 7
Exception:
The DEB Series unvented room heater is approved for
installation into the following unvented replaces:
The DEB Series unvented room heater may also be
installed into a Ventless Firebox Enclosure for Gas Fired
Decorative Type Unvented Room Heaters per IAS Require-
ment No. 2-97 ANSI Z21.91-2001 (typically referred to as a
"Universal Firebox"), as long as rebox hearth dimensions
meet the minimum hearth dimensions shown below.
C
A
D
B
FP2530
hearth dims
DEB20 27” 13Z\v” 18” 17”
(686 mm) (337 mm) (457 mm) (432 mm)
DEB24 28Z\x” 13Z\v” 22Z\v” 17”
(724 mm) (337 mm) (565 mm) (432 mm)
DEB30 32Z\x” 13Z\v” 25Z\x” 17”
30” Logs (826 mm) (337 m) (648 mm) (432 mm)
Figure 1 -
Hearth Minimum Dimensions
FP2530
The following are guidelines for placing a gas log set in
a replace that has a restrictive barrier along the bottom
front opening of the replace. Some examples of barri-
ers are glass/screen door frames and sunken/recessed
replaces.
No Restriction 13Z\v”
0” to 1Z\x” 16”
Greater than 1Z\x” to 3” 16”
Greater than 3” *
*Any barrier greater than 3” placed in front of the gas log
set is not recommended by the manufacturer.
Non combustible material such as refractory brick
may be used to line the oor of the replace in order to raise
the height of the gas log set in relation to a restrictive barrier.
If the unit is raised, the minimum height dimension listed in
the homeowner’s manual must not be exceeded.
If the log set is equipped with a remote receiver, a
restrictive barrier may reduce the battery life by increasing
the ambient temperature inside the replace. Placement
of the receiver outside of the replace will extend the
battery life.
X
FP2794
logs in enclosure
Depth of Fire-
place/Firebox
(Refer to
Table)
The log set should
be placed against or
as near as possible
to the rear wall of the
replace
Glass door frames
with adjustable
louvers should
have the louvers
fully open while
the unit is in
operation
Height of restrictive bar-
rier caused by glass door
frames, recessed replaces,
etc. from the base or bottom
surface of the unit. (Refer to
Table).
Figure 2 -
Reference Drawing of a Natural
Flame Log Set in an Enclosure FP2794
DEB Unvented Gas Logs
844D0060
minimum clearances
Follow these instructions carefully to
ensure safe installation. Failure to follow
instructions exactly can create a fire
hazard.
The sides of the re-
place opening must be at least 16" from any combustible
wall. The ceiling must be at least 42" from the top of the
replace opening.
16"
42"
FP1996
wall ceiling clearances
Figure 3 -
Sidewall and Ceiling Clearances
FP1996
IMPORTANT: If you cannot meet these minimum clear-
ances you must operate the heater with chimney ue
damper open. Refer to “Installing Vented Applications”
found on page 17.
FP2795
Measure heat resist material
Heat Resis-
tant Material
Measure This
Distance
Heater in
Fireplace or
Firebox
FP2795
Figure 4 -
Measure Heat Resistant Material
Table A -
Heat Resistant Material Requirements with No
Mantel or Combustible Projection
12” or more Hood not required
8” or less than 12” Hood not required Extend heat
resistant mat’l to
12” or install hood
Figure 4
Less than 8” Extend heat resistant Extend heat
material to at least 8” resistant mat’l to
and install hood. at least 8” and
Figure 4 install hood.
Figure 4.
, extend heat
resistant material
to a height of at
least 12”
To install the gas logs into a replace with no wooden
mantel, shelf or other combustible projection above the
replace opening, measure the heat resistant material
height, per Figure 4, then see TABLE A.
Heat resistant materials such as slate and marble must
DEB Unvented Gas Logs
44D0060 9
To install the heater with a wooden mantel, shelf or other
combustible projection above, rst measure the heat resis-
tant material shown in Figure 5, then refer to Table B.
FP2796
mantel
8” or More of
Heat Resistant
Material
Hood
Heater in Fire-
place or Firebox
FP2796
Figure 5 -
Measure Heat Resistant Material for Mantel
12” or more Hood not required. Hood not required.
Observe proles (side Observe prole (side
elevations) shown in Fig. 6 elevations) shown on
Page 10, Figure 8
8” to less than 12” Install hood and observe Install hood and ob-
proles shown on Page 10, serve proles shown in
Figure 8, OR, extend heat Figure 6, OR,
resistant material to at extend heat resistant
least 12” and observe material to at least 12”
proles shown in Fig. 6. and observe proles
shown on Page 10, Fig. 8
Less than 8” Extend heat resistant mat’l Extend heat resistant
to at least 8”, install hood material to at least 8”,
and observe proles shown install hood and observe
inFig. 7, OR prole shown in
extend heat resistant Fig. 6; OR extend
material to at least 12” and resistant material to at
observe proles shown in least 12” and observe
Fig. 7. proles shown on Page
10, Fig. 8.
Table B -
Heat Resistant Material Heights and Mantel Location
10”
8”
6”
256O”
8”
14”
2056O”
246”
28”
Fp2797
mantel no hood
Heat Resistant
Material
Heater in Fire-
place or Firebox
FP2797
Figure 6 -
DEB20 Minimum Mantel Clearance with No Hood
A mantel
may project from the
wall a of
2Z\x" at a of
14" above the opening,
and a maximum of 6"
at a of 20Z\x"
above the opening.
12”
10”
8”
6”
256O”
8”
1456O”
186”
2256O”
26”
FP2798
mantel with hood
Heat Resistant
Material
Heater in
Fireplace or
Firebox
Hood
FP2798
Figure 7 -
All Models Minimum Mantel Clearance with a Hood
A mantel may
project from the wall a
of 2Z\x" at a
of 8" above
the opening, and a maxi-
mum of 6" at a
of 14Z\x" above the open-
ing.
DEB Unvented Gas Logs
10 44D0060
10” or Less
28”
12”
Min.
Fp2799
mantel no hood 24
Heat Resistant
Material
Heater in Fire-
place or Firebox
FP2799
Figure 8 -
DEB24/30 Minimum Mantel Clearance with No Hood
The
bottom of the
mantel may project
from the wall a
maximum of 10" at
a minimum of 28"
above the opening.
7”
6”
256O”
4” 8”
1456O”
FP2800
bad mantel
Minimum of 8”
Heat Resistant
Material
Hood
Mantel
FP2800
Figure 9 -
DEB24/30 Example of Unsafe Installation - Mini-
mum Mantel Clearance with No Hood
Figure 9 is an example of an unsafe mantel installation.
This mantel projects 4" at 8" above the opening, exceed-
ing the maximum acceptable distance of 2Z\x" The mantel
also projects 7" at 14Z\x" above the opening, exceeding the
maximum acceptable distance of 6".
If your mantel prole is unsafe, you may either:
• Raise the mantel to an acceptable height
• Remove the mantel
5” Minimum
FP2876
combustible floor
Heater in
Fireplace or
Firebox
Combustible
Material
FP2876
The gas log heater must be installed at least 5" above any
combustible ooring material, such as carpeting or tile,
which is closer than 14" to the base of the replace. The
minimum distance must be maintained from the top surface
of carpeting, tile, etc. Figure 10
,
The gas log heater may be installed nearer to the oor if a
minimum of 14" of noncombustible material such as slate
or marble is installed between the base of the replace and
the combustible ooring. Figure 11
Figure 10 -
Minimum Clearance above Combustible Flooring
14” Minimum
FP2802
non combustible floor
Heater in
Fireplace or
Firebox Combustible
Material
This Distance
May Now be
Less than 5”
Figure 11 -
Minimum Clearance above Combustible Floor with Non-
combustible Material Installed at Base of Fireplace
DEB Unvented Gas Logs
44D0060 11
• Turn the gas supply to the replace or rebox.
• Seal any fresh air vents and/or ash clean-out doors
located on the floor or wall of the fireplace. If left
unsealed, drafting may cause pilot outage or sooting.
Use a heat resistant sealant.
Manual and millivolt controlled gas logs may be
installed as a vented decorative log set in compli-
ance with ANSI Z21.60 and National Fuel Gas Code,
Section 6.6.
Exception:
• Turn off gas supply to replace or rebox.
• Have the replace oor and chimney professionally
cleaned to remove ashes, soot, creosote or other
obstructions. Have this cleaning performed annually
after installation.
• Seal any fresh air vents or ash clean-out doors located
on oor or wall of replace. If not, drafting may cause
pilot outage or sooting. Use a heat-resistant sealant.
A damper stop must be provided with the unit. Contact your
dealer to obtain one. The damper stop must be installed as
shown in Figure 12 to prevent full closure of the replace
damper blade and provide a minimum 29 square inch ue
opening.
FP2538
damper stop
Damper
Stop
Damper
FP2538 Figure 12 -
Damper Stop Installation
(See Warning)
Placement in a
Fireplace with Restrictive Barrier
DEB Unvented Gas Logs
12 44D0060
FP2877
DEB secure to floor
1. Center the gas log unit in the replace or rebox. Make
certain the front feet of the grate sit inside the front edge
of the replace or rebox.
2. Anchor holes are located on the right and left sides of
the unit. After centering the grate correctly, mark the
hole positions on the replace/rebox oor. Drill two (2)
B\cx" diameter holes approximately 1Z\x" deep.
3. Anchor the grate to the replace/rebox oor using the
screws provided. Figure 13
Screws
Anchor
Holes
FP2803
Figure 13 -
Secure Heater to Floor of Fireplace or Firebox
A qualied gas appliance installer must connect
the heater to the gas supply. Consult all local codes.
Figure 14
FP2371
gas connect
Stainless
Flexible
Tube Pipe
Possible Locations
for Pressure
Tapping Point
Gas
Supply
Inlet
To
Heater
Valve
Pipe
Coupling
Manual Shutoff
Valve
FP2371
Figure 14 -
Gas Connection
, to reduce the supply tank pressure to a maximum of
13" w.c. This is in addition to the internal regulator in the
heater valve.
DEB Unvented Gas Logs
44D0060 13
The heater gas inlet connection is a 3/8" NPT at the valve.
On all control type units, the inlet connection is on the right
side of unit. To connect from the opposite side, route the
pipe around the back portion of the unit.
When tightening up the joint to the valve, hold the valve
securely to prevent movement.
Test all gas joints from the gas meter to the heater valve
for leaks using a gas analyzer or soap and water solution
after completing connection.
Check the gas pressure with the appliance burning and
the control set to .
Figure 15
If the pressure is not as specied,
replace the regulator with the correct part from the parts
list in this manual.
Remove 1/8" NPT plug, located on side of regulator body.
Install tting and tubing to pressure gauge. After taking
pressure reading, reinstall test plug. Check for gas leaks.
FP2499
manual valve
NPT Test Plug
FP2499
Figure 15 -
Manual Control Pressure
Test Point Location
Figure 16
The valve regulator controls the burner pressure which
should be checked at the pressure test point.
Turn captured screw counter clockwise two or thre turns
and then place tubing to pressure gauge over test point
(Use test point “OUT” closest to control knob). After taking
pressure reading, be sure and turn captured screw clock-
wise rmly to re-seal. Do not over torque. Check for gas
leaks.
FP2372
millivolt valve
Test Port “Out”
FP2372
Figure 16 -
Millivolt Control Pressure
Test Point Location
DEB Unvented Gas Logs
14 44D0060
FP2112
wiring diagram
12/08
Wall
Switch
On/Off Switch
On/Off
Switch
Millivolt
Valve
ODS Pilot
TH = 3
TP = 1
TP/TH = 2
ODS Pilot
Spade Terminal
Switch
Optional Wall
Switch, Remote
Receiver or
Optional T-Stat
FP2112
Figure 17 -
Wiring Diagram
The millivolt valve is a self-powered combination gas control
1. Use 18 awg, two-wire cable, 15 feet maximum length.
2. At one end of the cable, connect both wires to the wall
switch or thermostat. At the other end, connect one
wire to TP/TH and one wire to TH, or connect the wall
switch/thermostat to the two male (0.25") terminals on
the left side of the unit. The color of the wires does not
matter.
DEB Unvented Gas Logs
44D0060 15
FP2878
install remote receiver
Connect the connectors to the two (2) .25” male connectors
located on the right side when facing the unit. Figure 18.
Do not allow the wire to touch the grate or burners.
Heat reduces battery life. You can protect the
receiver and extend battery life by mounting the receiver
in a wall or other location outside the replace.
Remote
Wire
Connectors
Remote
Receiver
FP2878
Figure 18 -
Install Remote Receiver
OPTION SOLD SEPARATELY
1. Remove metal bracket and label from box.
2. Peel away the paper backing on the label. Align holes
in label with holes on the bracket. Right side of label
should ush with right side of bracket. Figure 19. Press
label rmly and smoothly to bracket.
3. Using Phillips screwdriver, install t-stat sensor to bracket
with two screws provided. Figure 20. Make sure the
thermo bulb wire is at the bottom of t-stat sensor.
4. Plug in wiring harnesses to back of t-stat sensor. Figure
20.
HIGH
LOW
26D3317
THERMOSTAT
SETTING
FP2879
place labor
Align
Holes
Align Edges of
Label to Right Side
of Bracket
FP2879
Figure 19 -
Apply Label to Bracket
HIGH
LOW
26D3317
THERMOSTAT
SETTING
FP2880
install sensors
Wiring
Harnesses
T-Stat Sensor
Bracket
Screws Thermo Bulb
FP2880
Figure 20 -
Install T-Stat Sensor and
Wiring Harnesses
DEB Unvented Gas Logs
16 44D0060
HIGH
LOW
26D3317
THERMOSTAT
SETTING
FP2881
install Tstat
5. Route wiring harnesses through large hole on side of
unit. Mount bracket to side of unit with screw provided.
Figure 21
6. Attach wiring harness to either TP/TH and TH on control
valve or to existing wiring harness with two (2) 0.250"
male spade terminals for remote or t-stat option. Figures
21 and 22.
Knob
Thermo Bulb
Screw
T-Stat Sensor
and Bracket
Wiring Harnesses
FP2881
Figure 21 -
Install T-Stat Sensor to DEB Base
FP2808
attach tstat to valve
Figure 22 -
Attach Wiring Harnesses to Control Valve
Wiring Harnesses
TH
TP/TH
FP2808
7. Install knob to shaft of t-stat sensor. Figure 21.
8. Place thermo bulb in front of the rebox for incoming
air.
DEB Unvented Gas Logs
44D0060 17
HIGH
LOW
26D3317
THERMOSTAT
SETTING
FP2882
DEB controls
1. Follow millivolt lighting instructions on lighting plate
attached to unit or in homeowner’s manual.
2. With control knob in the “ON” position make sure
the ON/OFF switch is in the “OFF” position. Figure
23
3. The unit is now being controlled by the thermostat
sensor. The sensor will now cycle the burners on
and off. You can adjust how often the unit cycles
by turning the control knob on the sensor.
Control Knob
On/Off Switch
T-Stat Sensor
FP2882
Figure 23 -
Control Knob in “ON” Position and
ON/OFF Switch in “OFF” Position
The millivolt system and individual components may be
checked with a millivolt meter having a 1-1000 mV range.
Conduct each check shown in chart by connecting meter
test leads to terminals as indicated.
A. Complete Millivolt System Check
(“A” Reading - Thermostat contacts CLOSED - Control
knob “ON” - Main burner should turn ON)
1. If reading is more than 175 millivolts and the au-
tomatic valve still does not come on, replace the
control.
2. If the closed circuit reading (“A” reading) is less
than 175 millivolts, determine cause for low read-
ing, proceed to Section B.
A Complete TP/TH and TH Closed Minimum 175
System
B Thermopile TP and TP/TH Open Minimum 500
Output
B. Thermopile Output Reading Check
(“B” Reading - thermostat contacts OPEN - Main burn-
er OFF
1. Check gas pressure to the unit. If gas pressure is
within minimum and maximum on data plate, then
check pilot voltage, 500 millivolts minimum. If the
minimum millivolt reading is not obtainable, replace
pilot.
DEB Unvented Gas Logs
18 44D0060
— This unit is supplied with four or ve
ceramic ber logs. Do not handle these logs with your bare
hands.
After handling the logs, wash your
hands gently with soap and water to remove any traces
of bers.
Figures 24 and 25
NOTE: Model DEB20 has 4 logs and models
DEB24 and DEB30 have 5 logs.
1. Install back log (#1) on two pins located near the
back of base. Check log position and stability.
2. Install right center log (#2) on pins located near
right front of base and center of base.
3. Install left center log (#3) on pin located near left
front of base and on top of right center log (#2).
4. Install middle front log (#4) in front of center log.
Make sure bottom of log is resting on the center of
grate. Do not let log #4 contact the front burner.
LG1024
DEB20 logs
Log #6
Log #4
Log #1
Log #1
Log #2
Left
Front
Pin
Right Front and
Center Pins
LG1024
Figure 24 -
Place Logs on Grate (DEB20)
5. Rest right end of left
front log (#5) on log #3 and the top of left front log
on log #1.
6. Place back end of top center log (#5) on recessed
area of back log (#1). Cross log #6 over log #2 and
rest right extension on grate. Log #6 should t on
pin on center log #3.
DEB Unvented Gas Logs
44D0060 19
LG1005
DEB24 30 logs
Log #6
Log #4
Log #3 Log #1
Log #5
(24 & 30
Only)
Log #2
Right Front
and Center
Pins
Back
Pins
LG1025
Left Front
Pin
Figure 25 -
Place Logs on Grate
(DEB24/30)
DEB Unvented Gas Logs
20 44D0060
It should just touch the top of the
thermocouple tip for natural. Refer to Figures 26 and 28
for correct pilot ame appearance.
If the pilot ame does not touch the thermocouple, then
the main burner cannot function reliably. Refer to Figures
27 and 29 for incorrect pilot ame appearance.
FP2273
pilot bad flame
FP2272
pilot correct flame
Figure 27 -
Incorrect Pilot Flame Appearance
Thermocouple
for Natural Gas
Thermocouple
for LP
FP2272
Thermocouple
for Natural Gas
Thermocouple
for LP FP2273
Figure 26 -
Correct Pilot Flame Appearance
FP2501
manual pilot flame
Thermocouple
for Natural Gas Thermocouple
for LP
Figure 28 -
Correct Pilot Flame Appearance
Figure 29 -
Incorrect Pilot Flame Appearance
FP2501
manual pilot flame
Thermocouple
for Natural Gas
Thermocouple
for LP
FP2502
In addition, periodically check the ames visually during
operation.
This manual suits for next models
14
Table of contents
Other Vermont Castings Gas Heater manuals
Vermont Castings
Vermont Castings Radiance RADVTCB Mounting instructions
Vermont Castings
Vermont Castings 3225 User manual
Vermont Castings
Vermont Castings A18PHKSN User manual
Vermont Castings
Vermont Castings 4050 User manual
Vermont Castings
Vermont Castings Stardance SDV30 User manual
Vermont Castings
Vermont Castings 3380 User manual
Vermont Castings
Vermont Castings Radiance RUVSOD 3370 Mounting instructions
Vermont Castings
Vermont Castings RADVTCB Mounting instructions
Vermont Castings
Vermont Castings SDDVTEB Mounting instructions
Vermont Castings
Vermont Castings VCBV10 Specification sheet
Vermont Castings
Vermont Castings NBST27 User manual
Vermont Castings
Vermont Castings SDDVT Series Mounting instructions
Vermont Castings
Vermont Castings Radiance RADVT Series Installation instructions
Vermont Castings
Vermont Castings SDDVTCB Mounting instructions
Vermont Castings
Vermont Castings 3926 Mounting instructions
Vermont Castings
Vermont Castings SDDVTCBSB Installation instructions
Vermont Castings
Vermont Castings UVS27R User manual
Vermont Castings
Vermont Castings SDDVRBD, SDDVRC, SDDVRCCB User manual
Vermont Castings
Vermont Castings SDDVTBSSB User manual
Vermont Castings
Vermont Castings SDVR Series Mounting instructions
Popular Gas Heater manuals by other brands
GHP Group
GHP Group Dyna-Glo IBF10PMDG manual
Desa
Desa Comfort Glow CGP11A OWNER'S OPERATION AND INSTALLATION MANUAL
Thermoheat
Thermoheat RA18LPL User's manual and operating instructions
Raypak
Raypak 130 Specifications
Flavel
Flavel MISERMATIC FORM series Installation, maintenance & user instructions
Comfort Glow
Comfort Glow CRL2718PA OWNER'S OPERATION AND INSTALLATION MANUAL
BuckMaster
BuckMaster 100 series instruction manual
New Buck Corporation
New Buck Corporation 61TV installation manual
WILMS
WILMS GH 40 TH operating manual
COMPANION
COMPANION COMP243 owner's manual
Rinnai
Rinnai Energysaver ES38 OWNER'S OPERATION AND INSTALLATION MANUAL
De Vielle
De Vielle DEF978180 instruction manual
Burley
Burley G4237 IMAGE Installation, servicing & user instructions
Universal
Universal ALL-PRO 100R-NG owner's manual
Dimplex
Dimplex HTN20BR Installation and operating instructions
Empire Heating Systems
Empire Heating Systems RH-50-7 Installation instructions and owner's manual
Stanley
Stanley ST-14A-CH-E instructions
Mirpol
Mirpol MIR-H73S Assembly and safety instructions