Vermont Castings OXDV30NV Mounting instructions
DO NOT STORE OR USE GASOLINE
OR OTHER FLAMMABLE VAPORS
AND LIQUIDS IN THE VICINITY
OF THIS OR ANY OTHER
APPLIANCE.
• Do not try to light any appliance.
• Do not touch any electric switch;
do not use any phone in your
building.
• Immediately call your gas supplier
from your neighbor’s phone. Follow
the gas suppliers instructions.
• If you cannot reach your gas
supplier call the re department.
This appliance may be installed in an after
market permanently located manufactured
(mobile) home where not prohibited by
local codes.
This appliance is only for use with the type
of gas indicated on the rating plate.
This appliance is not convertible for use
with other gases unless a certied kit is
used.
5123
Oxford cover
Homeowner’s Installation
and Operating Manual
30005123 1/13 Rev. 4
2
Oxford Direct Vent / Natural Vent Gas Heater
30005123
General Information.......................................................................................................3
Requirements for the Commonwealth of Massachusetts ..............................................4
Stove Dimensions .........................................................................................................5
Installation Requirements ..............................................................................................6
Locating the Stove.........................................................................................................6
Clearance Requirements...............................................................................................6
Parallel & Corner Installation .........................................................................................7
Wall and Ceiling Clearances .........................................................................................7
Hearth Requirements ....................................................................................................7
Gas Specications.........................................................................................................8
Gas Inlet and Manifold Pressures .................................................................................8
High Elevations .............................................................................................................8
Horizontal Termination - Direct Vent ONLY ...................................................................8
Vertical Termination - Direct Vent ONLY ........................................................................9
Vent Termination Clearances ........................................................................................9
General Venting Information - Termination Location ................................................... 11
Termination Clearances...............................................................................................12
Venting Requirements - Natural Vent ONLY ...............................................................12
Venting Requirements and Options - Direct Vent ONLY .............................................13
Install the Optional Fan ...............................................................................................14
Venting System Assembly - Direct Vent ......................................................................15
Install Vent Adapter Pipe (Vermont Castings Group Vent Components) .....................15
Install Vent Adapter Pipe ( Dura-Vent Components) ...............................................16
Side Wall Termination Assembly .................................................................................15
Vent Termination Below Grade ....................................................................................18
Vertical (Through the Roof) Vent Assembly.................................................................18
Venting System Assembly - Natural Vent ....................................................................19
Install the Vent Pipe.....................................................................................................19
Install the Log Set........................................................................................................20
Connect Gas Supply Line............................................................................................20
Burner Information.......................................................................................................21
Air Shutter Adjustment & Instructions ..........................................................................21
Complete the Assembly...............................................................................................22
Install ON/OFF Switch .................................................................................................22
Thermostat Connection (Optional) ..............................................................................23
Install the Front and Top Plates ...................................................................................23
Your First Fire ..............................................................................................................24
Pilot and Burner Information........................................................................................24
Flame & Temperature Adjustment ..............................................................................24
Flame Characteristics ..................................................................................................24
Lighting and Operating Instructions.............................................................................25
Troubleshooting - SIT NOVA 820 Gas Control System ...............................................26
Fuel Conversion Instructions .......................................................................................27
Annual System Inspection ...........................................................................................30
Logset and Burner/Cleaning and Inspection ...............................................................30
Care of Cast Iron .........................................................................................................30
Cleaning the Glass ......................................................................................................30
Glass Replacement .....................................................................................................30
Gasket Replacement ...................................................................................................31
Inspect the Vent System Annually ...............................................................................31
Check the Gas Flame Regularly .................................................................................31
Stove Disassembly ......................................................................................................31
Wiring Diagram ............................................................................................................32
....................................................................................................................................33
...................................................................................................................................35
....................................................................................................................................39
....................................................................................................................................40
3
Oxford Direct Vent / Natural Vent Gas Heater
30005123
The Oxford Direct Vent/Natural Vent Room Heater, Model
No. OXDV30NV, is a vented gas appliance listed to the ANSI
standard Z21.88-2009 and CSA-2.33-2009 for Vented Room
Heaters, and CSA 2.17-M91, Gas-Fired Appliances For Use
at High Altitudes.
The installation of the Oxford Direct Vent/Natural Vent Room
Heater must conform with local codes, or in the absence of lo-
cal codes, with National Fuel Gas Code, ANSI Z223.1/NFPA
54 — latest edition and CSA B-149.1 Installation Code. (EX-
CEPTION: Do not derate this appliance for altitude. Maintain
the manifold pressure at 3.5” w.c. for Natural Gas and 10.0”
w.c. for LP gas at maximum input.)
This appliance is only for use with the type of gas indicated
on the rating plate. This appliance is not convertible for use
with other gases unless a certied kit is used.
The Oxford Direct Vent/Natural Vent Room Heater and its
individual shut-off valve must be disconnected from the gas
supply piping during any pressure testing of that system at
test pressures in excess of 1/2 psig (3.5 kPa).
The Oxford Direct Vent/Natural Vent Room Heater must be
isolated from the gas supply piping system by closing its in-
dividual manual shutoff valve during any pressure testing of
the gas supply piping system at test pressures equal to or
less than 1/2 psig.
‘Direct Vent’ describes a sealed combustion system in which
incoming outside air for combustion and outgoing exhaust en-
ter and exit through two separate concentric passages within
the same sealed vent system. The system does not use room
air to support combustion. The Direct Vent system permits
the gas appliance to be vented directly to the outside atmo-
sphere through the side of the house or vertically through the
roof. Conventional venting systems (Natural Vent) take air
from the room for combustion and vent the exhaust vertically
through the roof to the atmosphere.
This appliance is approved for bedroom installations in the
U.S. and Canada.
This appliance may be installed in an aftermarket* manufac-
tured (mobile) home, where not prohibited by state or local
codes.
The Oxford Direct Vent/Natural Vent Room Heater, when in-
stalled, must be electrically grounded in accordance with lo-
cal codes or, in the absence of local codes, with the National
Electrical Code ANSI/NFPA 70, (latest edition), or of the cur-
rent Canadian Electrical Code C22.1.
Fuels used in gas, woodburning or
oil red appliances, and the products of combustion of such
fuels, contain chemicals known to the State of California to
cause cancer, birth defects and other reproductive harm.
California Health & Safety Code Sec. 25249.6
Completion of sale, nor for purpose of resale, from the
manufacturer.
4
Oxford Direct Vent / Natural Vent Gas Heater
30005123
All gas tting and installation of this heater shall only be
done by a licensed gas tter or licensed plumber.
For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in whole
or in part for residential purposes, including those owned
or operated by the Commonwealth and where the side wall
exhaust vent termination is less than seven (7) feet above
nished grade in the area of the venting, including but not
limited to decks and porches, the following requirements
shall be satised:
At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gas tter
shall observe that a hard wired carbon monoxide detector
with an alarm is installed on each additional level of the
dwelling, building or structure served by the side wall
horizontal vented gas fueled equipment. It shall be the
responsibility of the property owner to secure the services
of qualied licensed professionals for the installation of
hard wired carbon monoxide detectors.
In the event that the side wall horizontally vented gas fueled
equipment is installed in a crawl space or an attic, the hard
wired carbon monoxide detector with alarm and battery
back-up may be installed on the next adjacent oor level.
In the event that the requirements of this subdivision can not
be met at the time of completion of installation, the owner
shall have a period of thirty (30) days to comply with the
above requirements; provided, however, that during said
thirty (30) day period, a battery operated carbon monoxide
detector with an alarm shall be installed.
Each carbon monoxide detector as required in accordance
with the above provisions shall comply with NFPA 720 and
ANSI/UL 2034 listed and IAS certied.
A metal or plastic identication plate shall be permanently
mounted to the exterior of the building at a minimum height
of eight (8) feet above grade directly in line with the exhaust
vent terminal for the horizontally vented gas fueled heating
appliance or equipment. The sign shall read, in print size no
less than one-half (1/2) inch in size,
The state or local gas inspector of the side wall horizontally
vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector observes
carbon monoxide detectors and signage installed in
accordance with the provisions of 248 CMR 5.08(2)(a)1
through 4.
The following equipment is exempt from 248 CMR
5.08(2)(a)1 through 4:
• The equipment listed in Chapter 10 entitled “Equipment
Not Required To Be Vented” in the most current edition
of NFPA 54 as adopted by the Board; and
• Product Approved side wall horizontally vented gas fueled
equipment installed in a room or structure separate from
the dwelling, building or structure used in whole or in
part for residential purposes.
When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting
system design or venting system components with the
equipment, the instructions provided by the manufacturer
for installation of the equipment and the venting system
shall include:
• Detailed instructions for the installation of the venting
system design or the venting system components;
and
• A complete parts list for the venting system design or
venting system.
When the manufacturer of a Product Approved side wall
horizontally vented gas fueled equipment does not provide
the parts for venting the ue gases, but identies “special
venting systems”, the following requirements shall be
satised by the manufacturer:
• The referenced “special venting system” instructions shall
be included with the appliance or equipment installation
instructions; and
• The “special venting systems” shall be Product
Approved by the Board, and the instructions for that
system shall include a parts list and detailed installation
instructions.
A copy of all installation instructions for all Product Approved
side wall horizontally vented gas fueled equipment, all
venting instructions, all parts lists for venting instructions,
and/or all venting design instructions shall remain with
the appliance or equipment at the completion of the
installation.
5
Oxford Direct Vent / Natural Vent Gas Heater
30005123
C
L
Valve Inlet
23"
(584mm)
66M"
(172mm)
2456O"
(622mm)
C
L Valve
Inlet
5123
Oxford dims
286"
(721mm)
1256O"
(318mm)
17"
(419mm)
46"
(111mm)
Refer to Page 6 for Flue Collar
Centerline Dimensions
Oxford dimensions.
6
Oxford Direct Vent / Natural Vent Gas Heater
30005123
The installation must conform with local codes or, in the
absence of local codes, with the National Fuel Gas Code,
ANSI Z223.1/NFPA 54 - latest edition. (EXCEPTION: Do
not derate this appliance for altitude. Maintain the mani-
fold pressure at 3.5” w.c. for Natural Gas, and 10” w.c. for
Propane).
In Canada, installation must be in accordance with the cur-
rent CSA B-149.1 Installation Codes and/or local codes.
A
B
E
C
D
ST207b
Dutchwest
Stove locations
5/15/03 djt
A. Flat on corner wall D. Cross Corner
B. Room Divider E. Flat on wall
C. Island ST207b
Possible stove locations.
Measure side clearances as shown in Figures 5 and 6
from the outer edge of the cast iron stove top. Measure
rear clearances from the outermost surface of the steel
rear skirt.
The heater is approved for installation into an alcove con-
structed of combustible materials to the dimensions and
clearances shown on the next page.
The same clearances apply in a standard parallel instal-
lation.
• Always maintain required clearances (air
spaces) to nearby combustibles to prevent
re hazard. Do not ll air spaces with insula-
tion. All venting components must maintain a 1”
(25 mm) clearance to combustible materials. Main-
tain a 6” (150 mm) clearance when using a single
wall pipe.
• The gas appliance and vent system must be vented
directly to the outside of the building and never be
attached to a chimney serving a separate solid fuel
or gas-burning appliance. Each direct vent appli-
ance must use its own separate vent system. Com-
mon vents are prohibited.
• Refer to the manufacturer’s instructions included
with the venting system for complete installation
procedures.
WARNING
!
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
In choosing a location for the stove, consider:
• The location of outside walls;
• Where additional heat is needed:
• Where family members gather most often;
• The vent system requirements.
We do not recommend the use of wallpaper next
to this stove. Over time, radiant heat may cause the wall-
paper to shrink, or may adversely affect the binders in the
wallpaper adhesive.
7
Oxford Direct Vent / Natural Vent Gas Heater
30005123
ST129c
Dutchwest
corner specs
5/15/03 djt
A
A
B
B
ST129c
Stove Clearance A: 4” (102 mm)
Pipe Centerline B: 14Z\x” (370 mm)
Corner installation, minimum corner clearances and ue
centerline.
A
C
D
ST1122
Min. clearance
B
A: Rear Wall 4” (102 mm)
B: Min. Clearance 45Z\x” (1156 mm)*
C: Min. Alcove Height 73Z\x” (1867 mm)*
D: Max. Alcove Depth 48” (1220 mm)
Sidewall Clearance 4” (102 mm)
* needed for installing DuraVent Minimum Vent Kit #2792 or Vermont Cast-
ings Group Minimum Vent Kit #7TFSDVSK. ST1122
Dimensions and clearances to ceiling or alcove.
ST1121
wall thimble
A
A
Effective Minimum
Wall Thimble 57Z\x” (1461 mm) (Vermont Castings Group
Pipe)
Centerline 53Z\x” (1359 mm) (Simpson DuraVent Pipe)
ST1121
Minimum wall thimble centerline.
The heater must be installed on rigid ooring. When the
heater is installed directly on any combustible surface
other than wood ooring, a metal or wood panel extend-
ing the full width and depth of the unit must be used as the
hearth. There are no other hearth requirements.
ST128b
Stardance
flue centerline
9/28/00 djt
C
L
C
L
B
D
C
A
Stove Clearances A: 4” (102 mm)
B: 4” (102 mm)
Pipe Centerlines C: 15Z\x” (395 mm)
D: 9” (229 mm)
Parallel installation, minimum back and side clearances
and ue centerlines.
ST128c
8
Oxford Direct Vent / Natural Vent Gas Heater
30005123
2465 Nat Millivolt 28,000 20,000
2466 Prop Millivolt 28,000 19,000
Weight: Fully assembled; 202 lbs.
Natural LP (Propane)
Inlet Minimum 5.5” w.c. 11.0” w.c.
Inlet Maximum 14.0” w.c. 14.0” w.c.
Manifold Pressure 3.5” w.c. 10.0” w.c.
The vent must rise vertically a minimum of 24” (610 mm)
off the top of the unit, before the rst elbow. The horizontal
run may extend up to 20’ (6 m) and include a vertical rise
of up to 40’ (12 m). (Fig. 7) Horizontal termination must
also meet the criteria shown in Figures 9 through 11.
• Approved vent systems must terminate above and in-
cluding the heavy line in Figure 7.
• Two 45° elbows may be substituted for each single 90°
elbow.
• With a rise between 2’ - 5’, one 90° or two 45° elbows
may be used.
20
19
18
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Vertical Run (in feet)
(Measured from the appliance flue collar to the top of the vent pipe.)
Horizontal Run (in feet)
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
ST134a
FDV28
Horizontal
vent run
12/3/99 djt
areas modified
1/11/00 djt
ST134a
Horizontal vent termination window.
May use up to three
90° Elbows
One 90°
Elbow
Unacceptable Venting
Conguration
9
Oxford Direct Vent / Natural Vent Gas Heater
30005123
A vertical vent system must terminate no less than 8’
(2.44 m) and no more than 40’ (12 m) above the appli-
ance ue collar. A 2Z\v” restrictor plate (supplied) must be
used where specied in all vertically terminated vent sys-
tems. (Fig. 8)
A vertically terminated vent system must also con-
form to the following criteria:
• No more than three 90° elbows may be used.
• Two 45° elbows may be substituted for one 90° elbow.
No more than six elbows may be used.
• Vent must rise a minimum of 2 feet before offset is
used.
• Termination height must conform to roof clearance as
specied in Figure 9.
20
19
18
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
Vertical Run (in feet)
(Measure from the appliance flue collar to the top of the vent pipe.)
Horizontal Run (in feet)
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
ST132a
FDV28
Vertical
vent run
12/3/99 djt
area
modified
1/11/00 djt
All Vertical Termina-
tions in this area
Require use of the
2Z\v” Restrictor Plate*
Vertical terminations
must be within this area
Unacceptable Venting
Conguration
No Restrictor Plate
ST132a
Vertical vent termination window.
When planning the installation, consider the location of
the vent terminal and clearances. Some of the most com-
mon clearances to keep in mind are shown in Figure 10.
The vent should be placed so that people cannot be
burned by accidentally touching the vent surfaces when
the stove is operating.
The vent termination should be located where it cannot be
damaged by such things as automobile doors, lawn mow-
ers or snowblowers and it should be located away from
areas where it could become blocked by snow, etc.
Some considerations are:
• Obstructions or impediments to venting.
• Nearby combustible materials that could come into
contact with combustion exhaust gases.
• Other nearby openings {within 12” (305 mm)} through
which exhaust gas could reenter the building.
• All vegetation within 3’ (76 mm) that may interfere with
the draft.
Other factors that inuence where the installation will be
sited include the location of outside walls, where addi-
tional heat may be desired in the home, where the family
members gather most regularly, and perhaps most impor-
tantly, the distance limitations of the venting system.
• The horizontal termination must not be recessed
into the exterior wall or siding.
• Horizontal vent runs must be level toward the vent
termination.
• Clearances around the vent termination must be
maintained.
• For installations using Simpson DuraVent pipe, par-
allel installations with minimum wall clearance have
restricted access for connecting the Horizontal Vent
Cap straps to the vent pipe. See the maker’s instruc-
tions for recommended installation procedures.
10
Oxford Direct Vent / Natural Vent Gas Heater
30005123
Your stove is approved to be vented either through the
side wall, or vertical through the roof.
•
•
•
• Venting terminals shall not be recessed into a wall or
siding.
• Horizontal venting must be installed on a level plane
without an inclining or declining slope.
There must not be any obstruction such as bushes, gar-
den sheds, fences, decks or utility buildings within 24”
from the front of the termination hood.
Do not locate termination hood where excessive snow or
ice build up may occur. Be sure to check vent termina-
tion area after snow falls, and clear to prevent accidental
blockage of venting system. When using snow blowers,
make sure snow is not directed towards vent termination
area.
It is imperative the vent termination be located observing
the minimum clearances as shown on this page.
11
Oxford Direct Vent / Natural Vent Gas Heater
30005123
V
V
V
V
V
V
V
X
X
X
D
E
B
B
B
C
B
M
B
A
J
K
F
L
VENT TERMINATION AIR SUPPLY INLET AREA WHERE TERMINAL IS NOT PERMITTED
H
I
Ýi`
Ãi`
Operable
Operable Fixed
Closed
V
B
CFM145a
DV Termin Location
5/01/01 Rev. 12/05/01
sta
INSIDE
CORNER DETAIL
V
A
G
N
N
CFM145a
A = Clearance above grade, veranda, porch, 12” (30cm) 12” (30cm)
deck, or balcony
B = Clearance to window or door that may be 6” (15cm) for appliances 6” (15cm) for appliances
opened < 10,000Btuh (3kW), 12” (30cm) < 10,000 Btuh (3kW), 9”
for appliances > 10,000 Btuh (3kW) and (23cm) for appliances > 10,000
< 100,000 Btuh (30kW), 36” (91cm) Btuh (3kW) and < 50,000 Btuh
for appliances > 100,000 Btuh (30kW) (15kW), 12” (30cm) for
appliances > 50,000 Btuh (15kW)
C = Clearance to permanently closed window 12” (305mm) recommended to 12” (305mm) recommended to
prevent window condensation prevent window condensation
D = Vertical clearance to ventilated soft located
above the terminal within a horizontal 18” (458mm) 18” (458mm)
distance of 2 feet (610mm) from the center
line of the terminal
E = Clearance to unventilated soft 12” (305mm) 12” (305mm)
F = Clearance to outside corner see next page see next page
G = Clearance to inside corner (see next page) see next page see next page
H = Clearance to each inside of center line 3’ (91cm) within a height of 15’ (5m) 3’ (91cm) within a height of 15’
extended above meter/regulator assembly above the meter/regulator assembly (5m) above the meter/regulator
assy
I = Clearance to service regulator vent outlet 3’ (91cm) 3’ (91cm)
J = Clearance to nonmechanical air supply inlet 6” (15cm) for appliances < 10,000 6” (15cm) for appliances
to building or the combustion air inlet to any Btuh (3kW), 12” (30cm) for < 10,000 Btuh (3kW), 9”
other appliances appliances > 10,000 Btuh (3kW) and (23cm) for appliances > 10,000
< 100,000 Btuh (30kW), 36” (91cm) Btuh (3kW) and < 50,000 Btuh
for appliances > 100,000 Btuh (30kW) (15kW), 12” (30cm) for
appliances > 50,000 Btuh (15kW)
K = Clearance to a mechanical air supply inlet 6’ (1.83m) 3’ (91cm) above if within 10’
(3m) horizontally
L = Clearance above paved sidewalk or paved 7’ (2.13m)† 7’ (2.13m)†
driveway located on public property
M = Clearance under veranda, porch, deck or 12” (30cm)* 12” (30cm)*
balcony
N = Clearance above a roof shall extend a minimum of 24” (610mm) above the highest point when it passes through the roof
surface, and any other obstruction within a horizontal distance of 18” (450mm).
1 In accordance with the current CSA-B149 Installation Codes
2 In accordance with the current ANSI Z223.1/NFPA 54 National Fuel Gas Codes
† A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and
serves both dwellings
* only permitted if veranda, porch, deck or balcony is fully open on a minimum 2 sides beneath the oor:
NOTE: 1. Local codes or regulations may require different clearances.
2. The special venting system used on Direct Vent appliances are certied as part of the appliance, with clearances tested and
approved by the listing agency.
3.Vermont Castings Group assumes no responsibility for the improper performance of the appliance when the venting system does
not meet these requirements.
Vent termination clearances.
12
Oxford Direct Vent / Natural Vent Gas Heater
30005123
Termination clearances.
FP567
NVBR/NVBC VENTING RUNS
11/12/97
Venting Runs
Horizontal Run (in feet)
Vertical Run (in feet)
(Measured from top of the unit before any elbow)
A: Vertical installations up to 36 feet (12m) in
height. Up to an 18 ft. horizontal vent run can be
installed within the vent system using a
maximum of two 90-degree elbows or four
45-degree elbows.
B: Vertical installations up to 36 feet (12m) in
height. Up to a 24 ft. horizontal vent run can be
installed within the vent system using a
maximum of two 45-degree elbows.
(Ratio = 2/3, Hor./Vert.)
= Acceptable venting configuration
= Unacceptable venting configuration
36
34
32
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
1 2 4 6 8 10 12 14 16 18 20 22 24
A
B
NOTE: When venting staight vertical, without any
elbow, a minimum of 8 ft. vertical is required
off the top of the stove.
FP567b
Vent termination window - Natural Vent ONLY.
Outside Corner
Inside Corner
Termination Clearances
Termination clearances for buildings with combustible and noncombustible exteriors.
G =
Combustible
6" (152 mm)
Noncombustible
2" (51 mm)
F =
Combustible
6" (152 mm)
Noncombustible
2" (51 mm)
G
Balcony -
with no side wall
M =
Combustible &
Noncombustible
12" (305 mm)
M
Balcony -
with perpendicular side wall
M = 12" (305 mm)
P = 6” (152 mm)
M
F
Alcove Applications*
C
D
C
E
V
V
Combustible &
Noncombustible
E= Min. 2” (51 mm) for
non-vinyl sidewalls
Min. 12” (305 mm) for
vinyl sidewalls
O= 8’ (2.4 m) Min.
O
P
V
V
V
584-15
No.
of Caps DMin. CMax.
1 3’ (914 mm) 2 x DActual
2 6’ (1.8 m) 1 x DActual
3 9’ (2.7 m) 2/3 x DActual
4 12’ (3.7 m) 1/2 x DActual
DMin. = # of Termination caps x 3
CMax. = (2 / # termination caps) x DActual
Termination in an alcove space (spaces open only on one side and with an overhang) is permitted with the dimensions
specied for vinyl or non-vinyl siding and softs. 1. There must be a 3’ (914 mm) minimum between termination caps. 2. All
mechanical air intakes within 10’ (1 m) of a termination cap must be a minimum of 3’ (914 mm) below the termination cap. 3. All
gravity air intakes within 3’ (914 mm) of a termination cap must be a minimum of 1’ (305 mm) below the termination cap.
13
Oxford Direct Vent / Natural Vent Gas Heater
30005123
The heater must be vented to the outdoors through an adjacent
exterior wall or through the roof. The venting system must be
comprised of the appropriate listed venting components speci-
ed on this page. These parts are available from DuraVent Cor-
poration or your Vermont Castings Group Dealer.
Refer to Figure 4 for dimensions relevant to the standard mini-
mum-vent kits.
www.duravent.com
Phone: 1-800-835-4429, Fax: 1-707-446-4740
Starter Pipe Assembly (incl. inner & outer sections) 2768*
90° Elbow, Blk. 46DVA-E90B*
45° Elbow, Gal. 46DVA-E45
6” Straight, Blk. 46DVA-D6B*
9” Straight, Blk. 46DVA-09B
11” - 14B\,” Adjustable Straight Section 46DVA-08AB
12” Straight 46DVA-12
24” Straight 46DVA-24B*
36” Straight 46DVA-36B
48” Straight 46DVA-48
Horizontal Vent Cap 46DVA-HC*
Wall Plate 46DVA-DC
Vinyl Siding Shield 46DVA-VSS
Snorkel Termination - 14” 46DVA-SNK-14
Snorkel Termination - 36” 46DVA-SNK30
Wall Strap 46DVA-WS
Cathedral Ceiling Support Box 46DVA-CS
Storm Collar 46DVA-SC
Wall Thimble 46DVA-WT
Firestop Spacer 46DVA-FS
Flashing 0/12 - 6/12 46DVA-F6
Flashing 6/12 - 12/12 46DVA-F12
Steel Chimney Conversion Kit
Kit A (6B\,” - 8B\,”) 46DVA-KCA
Kit B (6B\,” - 10Z\x”) 46DVA-KCB
Kit C (6B\,” - 13”) 46DVA-KCC
Masonry Chimney Kit 46DVA-KMC
Vertical Termination Cap (High Wind) 46DVA-VCH
Vertical Termination Cap (Low Prole) 46DVA-VC
*Included in Minimum Horizontal Vent Kit #2792
All DuraVent Straight vent pipe sections have a net length 1Z\x” (37mm)
less than the nominal dimension; i.e., a 6” (152mm) Straight pipe sec-
tion has an effective length of 4Z\x” (115mm).
The following kits are available to meet the needs of most in-
stallations. All pipe has a 7” outer diameter and includes a 4”
diameter inner section. A (CG) designation indicates the part is
nished in Charcoal Gray paint. Consult your dealer about other
vent parts that may be appropriate to complete the installation.
(1) 90-Degree Elbow (CG)
(1) 24” termination pipe (CG)
(1) 24-44” Adjustable Section
(1) Side Wall Termination, cool touch with siding shield
(1) Firestop
(1) Zero-clearance sleeve
(1) Hardware package
(1) Finishing plate (CG)
(1) Finishing collar (CG)
(4) Charcoal Gray ue pipe rings
(1) Combination Horizontal Offset / Roof Support
(1) Vertical Termination
(1) Storm Collar
(1) 1/12-6/12 Flashing
(1) Finishing Plate (CG)
(1) Finishing Collar (CG)
(1) Polished Brass Flue Pipe Ring
(1) Hardware Package
(1) 7/12 - 12/12 Flashing
and all of the other Vertical Termination parts.
(1) Flat Flashing
and all of the other Vertical Termination parts.
(1) 24” Non-adjustable Pipe
(1) Polished Brass Flue Pipe Ring
(1) 48” Nonadjustable Pipe
(1) Polished Brass Flue Pipe Ring
for vertical offsets
(1) 45-degree Elbow
(1) Polished Brass Flue Pipe Ring
www.selkirkcorp.com
1301 W. President George Bush Highway Ste. 330
Richardson, TX 75080
Phone: 1-800-992-8368, Fax: 1-877-393-4145
Appliance Adapter 4DT-AAV
90° Elbow, Blk. 4DT-EL90B
45° Elbow, Blk. 4DT-EL45B
6” Straight, Blk. 4DT-06B
9” Straight, Blk. 4DT-09B
4” - 10” Adjustable Straight Section, Blk. 4DT-AJ12
12” Straight, Blk. 4DT-12B
18” Straight, Blk. 4DT-18B
24” Straight, Blk. 4DT-24B
36” Straight, Blk. 4DT-36B
48” Straight, Blk. 4DT-48B
Horizontal Vent Cap 4DT-HC
Wall Plate 4DT-WT
Vinyl Siding Shield 4DT-VS
Snorkel Termination - 14” 4DT-ST14
Snorkel Termination - 36” 4DT-ST36
Wall Strap 4DT-WS/B
Cathedral Ceiling Support Box 4DT-CCS
Storm Collar 4DT-SC
Firestop Spacer 4DT-FS
Flashing 0/12 - 6/12 4DT-AF6
Flashing 6/12 - 12/12 4DT-AF12
Steel Chimney
Horizontal Kit A 4DT-HKA
Horizontal Kit B 4DT-HKB
Vertical Kit 4DT-VKC
Masonry Chimney Kit 4DT-MCK
Vertical Termination Cap 4DT-VC
Direct vent pipe may be used on the Natural Vent system
from the top of the draft hood adapter to the ceiling.
14
Oxford Direct Vent / Natural Vent Gas Heater
30005123
If you are installing the optional convection Fan Kit #2767
(FK26), continue here. If you are not installing a Fan Kit,
go to Page 15, Venting System Assembly.
1. The fan kit includes a Blower Assembly and a Rheostat
Assembly, connected by a cable. (Fig. 12) The Blower
Assembly mounts to the bottom rear of the stove, and
the Rheostat mounts to the valve coverplate. The as-
sembly includes a ‘snapstat’ which automatically turns
the fan On (or Off) above (or below) approximately
109°. The Rheostat also provides a range of fan speed
settings from Off (which overrides the snapstat func-
tion) to High. Unpack and inspect the Blower assem-
bly. Conrm that the fan spins freely.
This appliance is equipped with a three-prong (ground-
ed) plug for your protection against shock hazard and
should be plugged directly into a properly grounded
three-prong receptacle. Do not cut or remove the
grounding prong from this plug.
ST473
Fan parts
#2767 FK26
9/29/00
Snapstat
Bracket
Snapstat/
Extension
Assembly
Not Used on RF
Models
Not Used
on
Oxford
Blower
Assembly
Connect to PC Board on
RF Models Only
Not Used
on RF
Models
Rheostat
Assembly
ST473
Fan kit components.
2. Remove the rear skirt insert panel at the bottom of the
Rear Skirt (Fig. 13) and fasten the blower assembly to
the rebox back with the two Phillips pan-head bolts
originally installed in the rebox back. (‘1’, Fig. 14)
3. Attach the snapstat assembly to the snapstat bracket
with two sheet-metal screws. (‘2’, Fig. 14) Attach the
snapstat bracket to the stove with a hex-head bolt
passing through the bracket and into the stove base.
(‘3’, Fig. 14)
4. The rheostat control switch attaches to the left side of
the valve bracket at the front of the stove.
• Remove retaining nut from shaft of rheostat. (if pre-
installed)
• Insert the rheostat through the hole in the back of
the left side of the valve bracket, aligning the locator
pin with the smaller hole in that bracket.
• Thread the retaining nut onto the shaft of the rheo-
stat, tightening with a wrench. Do not overtighten.
• Attach the control knob to the rheostat shaft.
• Use the wire tie to secure the fan and rheostat wire
harnesses together.
ST1123
rear skirt insert
Made in USA
Rear Skirt
Sheet Metal
Screws
Rear Skirt Insert ST757
Remove rear skirt insert.
ST314
Fk26ce
attach fan
1/24/00
Star Washer
Sheet Metal Screws
Phillips
Pan Head
Bolts
Star
Washer
Snapstat
1/4” - 20
Hex Bolt
Snapstat
Bracket
ST314
1
2
3
Attach the fan assembly and the snapstat.
ST758
Dutchwest
attach rheostat
5/15/03 djt
Rheostat
Retaining Collar
Rheostat Knob ST758
Attach the fan rheostat.
15
Oxford Direct Vent / Natural Vent Gas Heater
30005123
The Oxford is approved for installation only with the vent
components listed on Page 13. Follow the vent compo-
nent instructions exactly.
The venting system must conform
with local codes and/or the current National Fuel Gas
Code, ANSI Z223.1/NFPA 54.
The venting system must
conform to the current CSA B149.1 installation code.
Consult the ‘Vent Run
Specications’ on Page 8 to determine whether the
restrictor plate is needed. If so, put the restrictor plate
in place within the inner ue collar as shown in Figure
16.
Apply a 1/4” bead of
cement around the inside wall of the pipe, about 1”
from the end. Insert the pipe over the stove ue collar,
keeping the vertical seam oriented to the back of the
stove. Also, be sure to align holes on the pipe with the
holes on the ue collar of the rebox. Fasten the pipe
to the holes in the ue collar with the #12 x 1/2” sheet
metal screws provided. (Fig. 19)
ST759
Dutchwest
restictor plate
5/15/03
ST759
Install the restrictor plate only if required for the vent-
ing conguration. Refer to Page 9.
(found in with the logset),
to the next section of inner pipe.
• Run a bead of sealant about 1/2” from the upper
end of the Inner starter pipe and join the two sections
together.
• Drill three pilot holes into the Inner Starter and se-
cure the assembly with three sheet metal screws. (Fig.
17)
to the stove for the
purpose of determining the center line of the pipe on
the wall.
Dry t the outer elbow with
the vertical outer vent and conrm the centerline align-
ment with the wall thimble opening.
Remove the pipes and elbows before continuing with
Step 4.
• Run a bead of sealant around the bottom end of the
starter pipe and attach the assembly to the stove using
three 1/4-20 x 3/8” Phillips screws provided in the parts
bag. (Fig. 18)
ST211
attach inner pipe
to next section
12/4/99 djt
CEMENT
First Section of
Vent Pipe
#8 x 1/2” Sheet
Metal Screws
4” Inner
Starter Pipe
ST211
Connect the inner starter with the next section of inner
vent pipe.
ST760
attach inner assy
5/15/0 3 djt
CEMENT
ST760
Attach inner assembly to ue collar.
ST761
attach inner assy
5/15/03 djt
ST761
Fasten outer pipe with #12 x 1/2” sheet metal screw.
16
Oxford Direct Vent / Natural Vent Gas Heater
30005123
Consult Page 9 to deter-
mine whether the restrictor plate is needed. If so, place
the restrictor plate into the inner ue collar. (Fig. 16)
shipped with the log-
set. Using the starter pipe assembly listed on Page 7,
slide the inner section out to allow access.
• Run a bead of sealant around the bottom end of the
starter pipe and attach the assembly to the stove using
three 1/4-20 x 3/8” Phillips screws provided in the parts
bag. (Fig. 20)
Apply a 1/4” bead of
cement around the outside surface, about one inch
from the crimped end. (Fig. 21) Orient the vertical
seam to the rear, and insert the crimped end of the
outer pipe into the ue collar. Fasten with three sheet
metal screws provided.
ST762
dura vent
attach inner assy
5/15/03 djt
CEMENT
1/4-20 x 3/8
Phillips Screws
Inner Adapter
Pipe
ST762
Simpson DuraVent - install inner adapter pipe.
ST763
DW dura vent
attach outer assy
5/15/03 djt
ST763
Simpson DuraVent - install outer adapter pipe.
1. Locate the vent opening on the wall. Refer to Figure 5,
Page 7, to determine the opening centerline. It may be
necessary to rst position the stove and measure to
nd the hole location. Depending on whether the wall
is made of combustible materials, cut the opening to
the size shown in Figure 22. Combustible wall open-
ings must be framed as shown in Figure 22.
VO584-100
Vent Opening
2/99 djt
9C\,”
(240 mm
10”
(250 mm)
7Z\x”
(191 mm)
9C\,”
(240 mm
10”
(250 mm)
VO584-100
Locate vent opening.
2. Measure the wall thickness and cut the wall sleeve
sections to proper length (MAXIMUM 12”). Assemble
the sleeve with the #8 sheet metal screws supplied. At-
tach the restop plate to the sleeve end with the holes.
(Fig. 23) The wall sleeve is required in com-
bustible walls only.
3. Install the Wall Firestop/Sleeve assembly into the wall
cutout and fasten the restop to the wall cutout framing
members. (Fig. 23)
ZCS103
Zero Clearance Sleeve
& Firestop
12/6/99 djt
Sleeve
12”
(305 mm)
Max. Length
Firestop ZCS103
Assemble the wall sleeve and restop.
17
Oxford Direct Vent / Natural Vent Gas Heater
30005123
For DuraVent pipe only: Install vent pipe by aligning the
locking system together, sliding the pipes together and
twisting clockwise.
• Install 90° elbow. Twist lock as before.
• Slide the wall plate over horizontal run before attach-
ing the horizontal run to the elbow. Fasten wall plate to
wall.
4. For Vermont Castings Group Vent Pipe only: If nec-
essary, measure to determine the vertical length (X) of
pipe required from the adapter pipe to the wall cutout
centerline, including a 2” (51mm) overlap at the joint.
(Fig. 24) use a hacksaw or tin snips to trim the pipe as
needed.
ST764
DW
measure vertical vent
5/15/03 djt
ST764
Determine the vertical pipe length.
5. Install rst the inner then the outer straight pipe
section(s), trimmed end down, to the point of the el-
bow. Drill 3 holes through each joint and fasten with
sheet metal screws.
6. Seal and install the elbow using 3 sheet metal screws
at each joint.
7. Measure, and cut if needed, the appropriate length of
pipe section needed to make the connection through
the wall. Include a 2” overlap; i.e. from the elbow to
the outside wall face, about 2” or the distance required
if installing a second 90° elbow. (Fig. 25)
8. Slip the wall plate and trim collar over the interior end
of the horizontal pipe and install into the wall sleeve.
Seal the joint inside the wall plate if needed to keep
cold air from being drawn into the home.
9. Seal the ends and connect the horizontal pipe to the
elbow. Fasten the wall plate to the pipe with three
sheet metal screws. Slide the trim collar up against
the wall plate to cover the screws. (Fig. 26)
ST215
measure thru wall
12/6/99 djt
ST215
Measure the horizontal length.
ST216
install pipe thru wall
12/6/99 djt
Trim Collar
Wall
Sleeve
Wall Plate
ST216
Install the horizontal pipe and wall plate parts.
10. For both Vermont Castings Group and DuraVent
Systems: Install the vent terminal. (Fig. 27) Apply
high temperature sealant one inch from the ends of
the inner and outer collars. Guide the inner and outer
vent termination collars into the adjacent pipes. Dou-
ble check that the vent pipes overlap the collars by 2”.
Fasten the termination to the wall with the screws pro-
vided, and caulk the joint with weatherproof sealant.
11. For Vermont Castings Group only: Install Charcoal
Gray Pipe Rings (#7FSDRG) or Polished Brass Pipe
Rings (#7FSDRP) at pipe joints, if desired.
ST217
install wall terminal
12/6/99 djt
Seal Both
Terminal Ends
Caulk Plate Joint with
Weatherproof Sealant ST217
Install the vent terminal.
18
Oxford Direct Vent / Natural Vent Gas Heater
30005123
Install Snorkel Kit #7FSDVSKS when it is not possible to
meet the required vent termination clearances of 12” (305
mm) above grade level. The snorkel kit will allow instal-
lation depth of down to 7” (178 mm) below grade level.
The seven inches is measured from the center of the hori-
zontal vent pipe as it penetrates the wall.
Be sure to maintain side wall clearances and vent
run restrictions. Refer to Figures 3, 4, 7, and 8.
1. Establish the vent hole through the wall.
2. Remove soil to a depth of approximately 16” (406 mm)
below the base of the snorkel. Install a window well
(not supplied). Rell the hole with 12” (305 mm) of
coarse gravel and maintain a clearance of at least 4”
(102 mm) below the snorkel. (Fig. 28)
3. Install the vent system as described on Pages 15 -
17.
4. Be sure to make a watertight joint around the vent pipe
joint at the inside and outside wall joints.
5. Apply high temperature sealant around the inner and
outer snorkel collars. Join the pipes and fasten the
snorkel termination to the wall with the screws provid-
ed.
6. Level the soil to maintain a 4” clearance below the
snorkel.
ST1124
snorkel
Waterproof Seal
Around Pipe
Firestop
Window
Well
Drain
Snorkel
Termination
Cap
4” Clearance
Gravel
ST1124
Fig. 28 Snorkel kit installation.
ST219
snorkel detail
12/6/99 djt
Recessed Wall
Firestop
Finishing
Collar
7” Pipe
Wall Plate
Sheet Metal
Screws and
Bracket
Wall Screws
and Anchors
Waterproof
Seal Around
Pipe
ST219
Use extension brackets to mount snorkel against
recessed wall.
If the foundation is recessed, use extension brackets (not
supplied) to fasten the lower portion of the snorkel. Fas-
ten the brackets to the wall rst, and then fasten to the
snorkel with self-tapping #8 x 1/2” sheet metal screws.
Extend the vent pipes out as far as the protruding wall
face. (Fig. 29)
Note that all vertically terminated installations must in-
clude the restrictor plate included with the stove. Refer to
Figure 8, Page 9.
Make certain the vent system conforms to all other re-
quirements for vertical termination as specied on Page
9.
This installation will require you to rst determine the roof
pitch and use the appropriate vent components. Refer to
Figures 8 and 9 on Pages 9 and 11.
1. Locate the nal position of the stove, observing all
clearances for both the vent and the stove.
2. Plumb to the center of the inner (4”) ue collar from the
ceiling above, and mark that location.
3.
C\,C\,
4. Plumb any additional opening through the roof or oth-
er construction that may be needed. In all cases, the
opening must provide a minimum of 1” (25 mm) clear-
ance to the vent pipe.
5. Place the stove in its nal position.
6. Install restop(s) #7DVFS and Attic Insulation Shield
#7DVAIS as needed. (Fig. 30) If there is a room above
ceiling level, a restop must be installed on both the
bottom and top sides of the ceiling joists. If an attic is
above ceiling level, an attic insulation shield must be
installed.
7. Install the appropriate roof support and ashing, mak-
ing certain that the upper ange of the ashing base is
below the shingles. (Fig. 31)
19
Oxford Direct Vent / Natural Vent Gas Heater
30005123
8. Install appropriate pipe sections until the vent run
reaches above the ashing. The enlarged ends of the
vent sections always face downward.
9. Install the storm collar and seal around the joints. (Fig.
31)
10. Add additional vent lengths to achieve the proper
overall height.
11. Apply cement to the inner and outer termination col-
lars and install the terminal cap.
ST222
vent thru ceiling
12/99
#7DVAIS
Attic
Insulation
Shield
#7DVFS
Firestop
In Upper
Floor
#7DVFS
Firestop in
Ceiling
Use Four 8d
Nails
ST222
Install restops and attic insulation shield.
ST221
vent thru roof
12/99
Storm Collar
Sealant
Upper
edge of
ange goes
under upper
shingles
Flashing
#7DVSKV
(A, B of F)
Roof Support ST221
Roof support and ashing.
The heater is shipped from the factory as a Direct Vent
Heater. It may be converted to a Natural Vent heater by
installing the Model FSDHAG Draft Hood Adapter.
The heater is approved for installation as a Natural Vent.
Vermont Castings Group Direct Vent pipe could be used
directly after the Draft Hood Adapter up to the ceiling,
then B-vent pipe must be used. Do not mix types of B-
vent pipe; use components from one maker or the other.
Follow the vent component maker’s instructions exactly.
The heater will also accept standard or enamelled 7” (150
mm) diameter pipe, around the Type B venting, for deco-
rative purposes only. (Fig. 32)
ST358
DW
Decorative
pipe around b-vent
5/15/03 djt
Decorative 7”
Pipe
4” B-vent
Pipe
Draft Hood
Adapter
Vermont Castings
Group Direct Vent
System may be
used Draft Hood up
up to the ceiling
ST766
Decorative 7” pipe may be tted around the B-vent
pipe.
The stove, when installed as a Natural vent heater, in-
cludes a vent safety switch. (Fig. 63, Page 32) Operating
the stove when it is not connected to a properly installed
and maintained venting system, or tampering with or dis-
connecting the vent safety switch, can result in carbon
monoxide (CO) poisoning and possible death.
The venting system must conform
with local codes and/or the current National Fuel Gas
Code, ANSI Z22.1.
The venting system must
conform to the current CSA B149.1 installation code.
Apply a bead of sealant around bottom end of inner start-
er pipe (found in bag with logset) and attach to stove. Ap-
ply a bead of sealant around top of inner starter pipe and
install the FSDHAG Draft Hood according to Draft Hood
instructions. (Fig. 33)
20
Oxford Direct Vent / Natural Vent Gas Heater
30005123
Attach the rst section of venting to the draft hood. De-
pending on the length of the individual venting sections
and the lengths of the decorative pipe (if installed), you
may need to slip the decorative pipe over the venting sec-
tions before attaching upper sections to lower ones. The
sections of decorative pipe should be oriented with their
seams (if any) toward the wall; sections usually do not
need to be fastened at each joint, other than slip sections.
If the layout includes a slip section, this should be the last
section of pipe visible in the room, at the ceiling. Complete
the venting according to the vent maker’s instructions.
ST767
DW
attach draft hood
5/15/03 djt
CEMENT
ST767
Install draft hood adapter.
1. Remove the logs from their packaging, and inspect
each piece for damage.
2. Install the rear log centering it side to side on the sheet
metal shelf at the back of the rebox. (Fig. 34) The log
will touch both sides and the back wall of the rebox.
3. Install the right log by engaging hole on bottom with
pin on the rear log. (Fig. 34) Then set right bottom side
on the burner so the edge of the log touches the right
side of the rebox. The right log does not use the loca-
tor pins on the burner to stay in place.
4. Install the left log by engaging hole on bottom with pin
on rear log. (Fig. 34) Then set left bottom side on the
burner so the edge of the log touches the left side of
the rebox.
5. Loosely sprinkle the lava rocks directly on top of the
burner in front of and between the decorative grate
and the right and left logs. Use the lava rock to cover
brackets on the burner. (Fig. 35)
LG141
Stardance
Install logs 1
12/11/00 djt
Left Log Right Log
Rear Log Decorative Grate
LG141
Install the back, left and right logs.
Check the Rating Plate attached by a steel cable to the
rebox, to conrm that you have the appropriate rebox
for the type of fuel to be used. The Oxford may be con-
verted from one gas to another using the appropriate Fuel
Conversion Kit listed on Page 34.
Table of contents
Other Vermont Castings Indoor Fireplace manuals
Vermont Castings
Vermont Castings Merrimack Large Mounting instructions
Vermont Castings
Vermont Castings 647 BFC User manual
Vermont Castings
Vermont Castings VCFDVI31 User manual
Vermont Castings
Vermont Castings VCEF26 Assembly instructions
Vermont Castings
Vermont Castings 500DVM Manual
Vermont Castings
Vermont Castings Winter warm 2100 User manual
Vermont Castings
Vermont Castings LHER20 User manual
Vermont Castings
Vermont Castings 300DVB(N/P)(V/SC)7SB User manual
Vermont Castings
Vermont Castings Majestic BFC36 Mounting instructions
Vermont Castings
Vermont Castings 3232 User manual
Vermont Castings
Vermont Castings Encore 2547CE User manual
Vermont Castings
Vermont Castings WinterWarm Fireplace Insert or System User manual
Vermont Castings
Vermont Castings SB60 User manual
Vermont Castings
Vermont Castings DVM Series User manual
Vermont Castings
Vermont Castings Savannah SSI30 User manual
Vermont Castings
Vermont Castings EWF36A Mounting instructions
Vermont Castings
Vermont Castings LHER20 Mounting instructions
Vermont Castings
Vermont Castings ExtremeView 33XDV User manual
Vermont Castings
Vermont Castings VWDV70NTSCSB User manual
Vermont Castings
Vermont Castings SA36R User manual
Popular Indoor Fireplace manuals by other brands
Amantii
Amantii BI-40-XTRASLIM Series installation guide
Quadra-Fire
Quadra-Fire QFP38-LP owner's manual
Lennox Hearth Products
Lennox Hearth Products EBVSTNM-B Care and operation instructions
Quadra-Fire
Quadra-Fire 4100I-GD-B user guide
HEAT GLO
HEAT GLO CERONA-36-IFT installation manual
Twin-Star International
Twin-Star International ClassicFlame 33WM0194 manual
Efiamma
Efiamma Good 10 C Use and maintenance manual
barbas
barbas UNIVERSAL-6 60 Instructions for use
Kohlangaz
Kohlangaz Gosford Plus Installation, maintenance and user instruction
USSC
USSC 2020L OWNER'S OPERATION AND INSTALLATION MANUAL
Tenneker
Tenneker 10683309 user manual
Lennox Hearth Products
Lennox Hearth Products Merit CPF-38 Homeowner's care and operation instructions
Dimplex
Dimplex Amesbury AME20 Installation and operating instructions
Harman Home Heating
Harman Home Heating ShadowLight XL owner's manual
Planika
Planika Galaxy Burner User and installation manual
HEAT GLO
HEAT GLO RED60 owner's manual
xeoos
xeoos X5 Service manual
Sierra Flame
Sierra Flame WM-FML-STL Series manual