Verona VEBIG 24 Operation instructions

• USERS OPERATING INSTRUCTIONS
• INSTALLATION ADVICE
•IMPORTANT - PLEASE READ AND FOLLOW
I PORTANT - PLEASE READ AND FOLLOW
✓Before beginning, please read these instructions completely and carefully.
✓Do not remove permanently affixed labels, warnings, or plates from the product. This
may void the warranty.
✓Please observe all local and national codes and ordinances.
✓Please ensure that this product is properly grounded.
✓The installer should leave these instructions with the consumer who should retain
for local inspector's use and for future reference.
✓The electrical plug should always be accessible.
Installation must conform with local codes or in the absence of codes, the National Fuel
Gas Code ANSIZ223.1 - Iatest edition. Electrical installation must be in accordance with the
National Electrical Code, ANSI/NFPA70 - latest edition and/or local codes. IN CANADA:
Installation must be in accordance with the current CAN/CGA-B149.1 National Gas
Installation Code or CAN/CGA-B149.2, Propane Installation Code and/or local codes.
Electrical installation must be in accordance with the current CSA C22.1 Canadian
Electrical Codes Part 1 and/or local codes.
INSTALLATION IN MANUFACTURED (MOBILE) OME: The installation must conform with
the Manufactured ome Construction and Safety Standard, Title 24 CFR, Part 3280 [for-
merly the Federal Standard for Mobile ome Construction and Safety, Title 24, UD (Part
280)] or, when such standard is not applicable, the Standard for Manufactured ome
Installations, ANSI/NCSBCS A225.1, or with local codes where applicable.
INSTALLATION IN RECREATIONAL PARK TRAILERS: The installation must conform with
state or other codes or, in the absence of such codes, with the Standard for Recreational
Park Trailers, ANSI A119.5.
Installation of any gas-fired equipment should be made by a Iicensed plumber. A manual
shut-off valve must be installed in an accessible location in the gas line external to the
appliance for the purpose of turning on or shutting off gas to the appliance (In
Massachusetts such shutoff devices should be approved by the Board of State Examiners
of Plumbers & Gas Fitters).
B U I L T - I N G A S O V E N
for residential use only
odel: VEBIG 24 ..
Sta nless steel models only: This built-in oven is supplied with a protective film
on steel and aluminium parts. This film must be removed before installing/using the
appliance
.

2
✓Do not store or use gasoline or other flammable vapors and liquids
in the vicinity of this or any other appliance.
✓WHAT TO DO IF YOU S ELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your
building.
• Immediately call your gas supplier from a neighbor's phone.
Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
✓Installation and service must be performed by a qualified installer,
service agency, or the gas supplier.
WARNING: IF THE INFOR ATION IN THIS ANUAL IS NOT
FOLLOWED EXACTLY, A FIRE OR EXPLOSION AY RESULT
CAUSING PROPERTY DA AGE, PERSONAL INJURY, OR DEATH.
This ppli nce is designed nd m nuf ctured solely for the cooking of
domestic (household) food nd is not suit ble for ny none domestic
pplic tion nd therefore should not be used in commerci l environment.
The ppli nce gu r ntee will be void if the ppli nce is used within none
domestic environment i.e. semi commerci l, commerci l or commun l
environment.
WARNING
NEVER use this appliance as a space heater to heat or warm the
room. Doing so may result in carbon monoxide poisoning and
overheating of the oven.
WARNING!
The Governor of California is required to publish a list of substances known to the state of California to cause
cancer or reproductive harm and requires businesses to warn customers of potential exposures to such sub-
stances.
WARNING!: Gas appliances contain or produce substances which can cause death or serious illness and
which are known to the State of California to cause cancer, birth defects or other reproductive harm.
To reduce the risk from substances in fuel or from fuel combustion, make sure this appliance is installed, oper-
ated, and maintained according to the manufacturer's instructions.

3
Dear Customer,
Thank you for having purchased and given your preference to our product.
The safety precautions and recommendations reported below are for your own
safety and that of others. They will also provide a means by which to make full use
of the features offered by your appliance.
Please preserve this booklet carefully. It may be useful in future, either to your-
self or to others in the event that doubts should arise relating to its operation.
This appliance must be used only for the task it has explicitly been designed
for, that is for cooking foodstuffs. Any other form of usage is to be considered
as inappropriate and therefore dangerous.
The manufacturer declines all responsibility in the event of damage caused by
improper, incorrect or illogical use of the appliance.
DATA PLATE
CONVERSION LABEL

4
USER INSTRUCTIONS
I PORTANT PRECAUTIONS AND RECO -
ENDATIONS
After having unpacked the appliance, check to ensure that it is
not damaged.
In case of doubt, do not use it and consult your supplier or a pro-
fessionally qualified technician.
Packing elements (i.e. plastic bags, polystyrene foam, nails,
packing straps, etc.) should not be left around within easy reach
of children, as these may cause serious injuries.
The packaging material is recyclable and is marked with the
recycling symbol
.
✓
Do not attempt to modify the technical characteristics of the
appliance as this may become dangerous to use.
✓ Do not carry out cleaning or maintenance operations on the
appliance without having previously disconnected it from the
electric power supply.
✓ After use, ensure that the knobs are in OFF position.
✓ Do not allow children or other incapable people to use the
appliance without supervision.
✓ During and after use of the oven, certain parts will become
very hot. Do not touch hot parts.
✓ Keep children away from the oven when it is in use.
✓S ainless s eel models only: This oven is supplied with a
protective film on steel and aluminium parts. This film must be
removed before installing/using the appliance.
✓ Fire risk! Do not store flammable material in the oven.
✓Make sure that electrical cables connecting other appliances
in the proximity of the oven cannot become entrapped in the
oven door.
✓ Do not line the oven walls with aluminium foil. Do not place
shelves, broiler pan, pans or other cooking utensils on the
base of the oven chamber.
✓ The manufacturer declines all liability for injury to persons or
damage to property caused by incorrect or improper use of
the appliance.
✓ To avoid any possible hazard, the appliance must be installed
by qualified personnel only. Any repairs by unqualified persons
may result in electric shock or short circuit. In order to avoid
possible injuries to your body or to the appliance, do not
attempt any repairs by yourself. Such work should be carried
out by qualified service personnel only.
✓ Important! The use of suitable protective clothing/gloves is
recommended when handling, installing or cleaning of this
appliance.
✓ Danger of burns! The oven and cooking accessories may
become very hot during operation. Make sure children are
kept out of reach and warn them accordingly. To avoid burns
use kitchen clothes and gloves when handling hot parts or
utensils.
✓ Stand away from the oven when opening oven door. ot air or
steam which escapes can cause burns to hands, face, and/or
eyes.
KEEP ATTENTION!!
STAND AWAY FRO THE CONTROL
PANEL LOUVERS (see figure above). HOT
AIR WHICH ESCAPES CAN CAUSE
BURNS TO HANDS, FACE, END/OR EYES.

5
I PORTANT PRECAUTIONS AND RECO -
ENDATIONS FOR USE OF ELECTRICAL
APPLIANCES
Use of any electrical appliance implies the necessity to follow a
series of fundamental rules. In particular:
✓ Never touch the appliance with wet hands or feet;
✓ Do not operate the appliance barefooted;
✓ Do not allow children or disabled people to use the appliance
without your supervision.
The manufacturer cannot be held responsible for any damages
caused by improper, incorrect or unreasonable use of the
appliance.
✓ Never clean the oven with a high-pressure steam cleaning
device, as it may provoke a short circuit.
✓ This appliance is intended for use in your household. Never
use the appliance for any other purpose!
✓ If you should decide not to use this appliance any longer (or
decide to substitute an older model), before disposing of it, it
is recommended that it be made inoperative in an appropriate
manner in accordance to health and environmental protection
regulations, ensuring in particular that all potentially haz-
ardous parts be made harmless, especially in relation to chil-
dren who could play with old appliances.
Remove the door before disposal to prevent entrapment.
✓ WARNING!!
This appliance shall not be used for space heating. This
information is based on safety considerations.
✓ Keep appliance area clear and free from combustible materi-
als, gasoline, and other flammable vapors.
✓ The misuse of oven door (e.g. stepping, sitting, or leaning on
them) can result in potential hazards and/or injuries.

6
CONTROL PANEL (Fig. 1.1)
1. Gas oven/gas broil control knob
2. Oven light control knob
3. Cooling fan warning light
4. 60’ alarm control knob
Fig. 1.1
1 4 23
control panel

CAUTION:
Gas appliances produce heat and humidity in
the environment in which they are installed.
Ensure that the cooking area is well ventilated
following national/local codes.
When the cooling fan failure warning light is OFF the cooling fan
motor is correctly operating. Operate the oven as 
per instruction manual.
When the cooling fan failure warning light is lighted this indicates
the malfunctioning of the cooling fan motor.
The oven can be used.
Disconnect the oven from the gas/electrical
mains and contact the After-Sales Service.
The oven cannot be used.
Shut-off valve
"close" position
1. Close the supply line
manual shut-off valve.
2. Disconnect the 3-prong
ground plug.
3. Contact the After-Sales
Service.

7
60’ alarm knob 
Fig. 2.1
INUTE COUNTER (fig. 2.1)
The minute counter is a timed acoustic warning device which can be set for a
maximum of 60 minutes.
The knob (Fig. 2.1) must be rotated clockwise as far as the 60 minute position and
then set to the required time by rotating it anticlockwise.
I PORTANT WARNING: This is only a mechanical timer.
Remember to turn off the oven/broil manually.

8
how to use the gas oven

Fig. 3.1
USING THE OVEN FOR THE FIRST TI E
It is advised to follow these instructions:
– Furnish the interior of the oven by placing the wire racks as described at chapter
“Cleaning and maintenance”.
– Insert shelves and tray.
–Turn the oven on to the maximum temperature (position ) to eliminate
possible traces of grease from the oven burner. The same operation should be
followed for broil burner.
– Switch off the electrical supply, let the oven cool down, then clean the interior
of the oven with cloth soaked in water and detergent (neutral) then dry carefully.
ATTENTION: the oven becomes
very hot during operation.
ATTENTION: the oven door
becomes very hot during operation.
KEEP CHILDREN AWAY.
WARNING:
The door is hot, use the handle.
OVEN BURNER
It carries out normal “oven cooking”.
The gas flow to the burner is regulated by a thermostat which allow to maintain the
oven temperature constant.
The control of the temperature is assured by a thermostatic probe positioned inside the
oven.
The probe must be always kept in its housing, in a clean condition, as an incorrect posi-
tion or encrustment may cause an alteration in the control of the temperature.
GENERAL FEATURES
The gas oven is provided with two burners:
a) Oven burner, mounted on the lower part of the oven (11000 BTU/hr)
b) Broil burner, mounted on the upper part of the oven (7000 BTU/hr).
OVEN THER OSTAT
The numbers printed on the control panel (fig. 3.1) indicate the increasing oven tem-
perature value (°F). To regulate the temperature, set the chosen number onto the knob
indicator.
The position serves only to turn on the broil burner.
GAS OVEN SETTING
Number printed on
the control panel
Temperature
in °F
Corresponding
temperature
in °C
200 93
250 121
300 149
350 177
400 204
450 232
500 260
550 288
N.B. When the oven is not being used, set the gas knob to the position and
also close the gas shut-off valve placed on the main gas supply line.
VERY I PORTANT
The oven/broil shall be used always
with the oven door closed.

9
햴
Attention: the oven door becomes very hot during operation.
Keep children away.
IGNITION OF THE OVEN BURNER
The thermostat allows the automatic control of the temperature.
The gas delivery to the oven burner is controlled by a two way thermostatic tap (oven
and broil burners) with flame-failure device.
To light the oven burner operate as follows:
1) Open the oven door to its full extent.
WARNING: Risk of explosion! The oven door must be open during this opera-
tion.
2) Press the oven control knob right down and, keeping it pressed, turn counter-clock-
wise (fig. 3.2) to max position .
3) Release the knob and check the oven burner has lit; if not, turn the knob clockwise
back to OFF and repeat the procedure from step 2.
4) Once the oven burner has lit, close the oven door slowly and adjust the burner
according to the power required.
If the flame extinguishes for any reason, the safety valve will automatically shut off the
gas supply to the burner.
To re-light the burner, first turn the oven control knob to position , wait for at least
1 minute and then repeat the lighting procedure.
Fig. 3.2
OVEN COOKING
Before introducing the food, preheat the oven to the desired temperature.
For a correct preheating operation, it is advisable to remove the tray from the oven and
introduce it together with the food, when the oven has reached the desired tempera-
ture.
Check the cooking time and turn off the oven 5 minutes before the theoretical time to
recuperate the stored heat.

10
햴
IGNITION OF THE BROIL BURNER
The broil burner generates the infra-red rays for broiling.
To light the broil burner operate as follow:
1) Open the oven door to the full extent.
WARNING: Risk of explosion!
The oven door must be open during this operation.
2) Press the oven control knob right down and, keeping it pressed, turn clockwise
(fig. 3.3) to the position.
3) Release the knob and check the broil burner has lit; if not, turn the knob
counterclockwise back to OFF and repeat the procedure from step 2.
4) Once the broil burner has lit, close the oven door slowly.
If the flame extinguishes for any reason, the safety valve will automatically shut off the
gas supply to the burner.
To re-light the burner, first turn the oven control knob to position , wait for at
least 1 minute and then repeat the lighting procedure.
Fig. 3.3
OVEN LIGHT
The oven is equipped with a light that illuminates the oven to enable visually controlling
the food that is cooking.
This light is controlled by a switch knob (Fig. 3.4).
To light the oven lamp turn the knob clockwise to position.
Fig. 3.4
Do always broil with oven door closed.
Attention: the oven door becomes very hot during operation.
Keep children away.

11
햴
1°STEP Do not use
2°STEP Broiling level
Oven cooking level
Oven cooking level
3°STEP
4°STEP
Fig. 3.5
BROILING
Very important: the broil burner must always be used with the oven door closed.
– Position the shelf on the second level from the top (fig. 3.5).
– Turn on the broil burner, as explained in the preceding paragraphs and let the oven
preheat for about 5 minutes with the door closed.
– Place the food to be cooked above the broiler pan.
– Introduce the broiler pan (fig. 3.6) in the oven. The broiler pan should be placed
above the shelf and it should be centered with the broil burner (fig. 3.5).
Do not broil without using the broiling pan.
Important: Use always suitable protective gloves when inserting/removing the
broiling pan, shelves, pans or other cooking utensils from the oven.
WRONG
CORRECT
Fig. 3.6
Fig. 3.7
Fig. 3.8

12
Do not use a steam cleaner
because the moisture can get into
the appliance thus make it unsafe.
GENERAL RECO ANDATION
✓Important: Before any operation of cleaning and maintenance disconnect the
appliance from the electrical supply.
✓It is advisable to clean when the appliance is cold and especially for cleaning the
enamelled parts.
✓Avoid leaving alkaline or acidic substances (lemon juice, vinegar, etc.) on the
surfaces.
✓Avoid using cleaning products with a chlorine or acidic base.
✓The use of suitable protective clothing/gloves is recommended when handling,
cleaning this appliance.
WARNING
When correctly installed, your product meets all safety requirements laid down for
this type of product category. However special care should be taken around the
rear or the underneath of the appliance as these areas are not designed or
intended to be touched and may contain sharp or rough edges, that may cause
injury.
ENA ELLED PARTS
✓All the enamelled parts must be cleaned with a sponge and soapy water or other
non-abrasive products.
✓Dry preferably with a microfibre or soft cloth.
✓Acidic substances like lemon juice, tomato sauce, vinegar etc. can damage the
enamel if left too long.
PAINTED PARTS AND SILK-SCREEN PRINTED SURFACES
✓Clean using an appropriate product. Always dry thoroughly.
I PORTANT: these parts must be cleaned very carefully to avoid scratching
and abrasion.
You are advised to use a soft cloth and neutral soap.
STAINLESS STEEL ELE ENTS
✓Stainless steel parts must be rinsed with water and dried with a soft and clean
cloth.
✓For difficult dirt, use a specific non-abrasive product available commercially or a
little hot vinegar.
INSIDE OF OVEN
The oven should always be cleaned after use when it has cooled down.
The cavity should be cleaned using a mild detergent solution and warm water.
Suitable proprietary chemical cleaners may be used after first consulting with the man-
ufacturers recommendations and testing a small sample of the oven cavity.
Abrasive cleaning agents or scouring pads/cloths should not be used on the cavity sur-
face.
NOTE: The manufacturers of this appliance will accept no responsibility for damage
caused by chemical or abrasive cleaning.
Let the oven cool down and pay special attention no to touch the hot heating ele-
ments inside the oven cavity.
clean ng and ma ntenance

Before any operation of maintenance
disconnect the appliance from the
electrical mains supply.
WARNING
VERY IMPORTANT
Fig. 4.1
OVEN ACCESSORIES INSTALLATION AND RE OVAL
– ang up the wire racks “G” on the oven walls (fig. 4.1).
– Slide in, on the guides, the shelf etc. (fig. 4.2).
The rack must be fitted so that the safety catch, which stops it sliding out, faces the
inside of the oven.
– Position the broiler pan above the oven shelf.
– To dismantle, operate in reverse order.
Safety
catch
Do not use this step
Fig. 4.2
G

13
햵
L
Fig. 4.4
Fig. 4.5
Fig. 4.6
OVEN DOOR
The internal glass of the oven door can be easily removed for cleaning by unscrewing
the two lateral fixing screws (fig. 4.3).
Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door
glass since they can scratch the surface, which may result in shattering of the
glass.
Fig. 4.3
Do not store flammable material in the oven.
REPLACING THE OVEN LIGHT
Before any maintenance is started involving electrical parts of the appliance, it must be
disconnected from the power supply.
– Let the oven cavity and the broil burner cool down;
– Switch off the electrical supply;
– Remove the protective cover;
– Unscrew and replace the bulb with a new one suitable for high temperatures (300°C-
570°F) having the following specifications: 120V 60 z, 15W, E14.
– Refit the protective cover
NOTE: Oven bulb replacement is not covered by your guarantee
RE OVING THE OVEN DOOR
To facilitate oven cleaning, it is possible to remove the door.
Please follow the instructions carefully:
– Open the door completely.
– Push down the lever “L” and, keeping it in this position, slowly close the door in
order to block the hinge (fig. 4.4).
– Grip the door (as indicated in fig. 4.5) and, while closing it, release the two hinges as
shown in fig. 4.6.
– Rest the door on a soft surface.
DOOR ASSE BLY
– Grip the door with your hands placed near the hinges and raise the levers “ ” with
your forefingers (fig. 4.6)
– Insert the hinges in their position until levers “ ” are hooked.
– Open the door completely to obtain the release of levers “L”.

14
DO’S AND DO NOT’S
• Do always broil with the oven door closed.
• Do read the user instructions carefully before using the oven for first time.
• Do allow the oven to heat for one and a half hours, before using for the first time, in
order to expel any smell from the new oven insulation, without the introduction of
food.
• Do clean your oven regularly.
• Do remove spills as soon as they occur.
• Do always use oven gloves when removing food shelves and trays from the oven.
• Do not allow children near the oven when in use.
• Do not allow fat or oils to build up in the oven base, or oven accessories.
• Do not place cooking utensils or plates directly onto the oven base.
• Do not broil without using the broiler pan.
• Do not place hot enamel parts in water. Leave them to cool first.
• Do not allow vinegar, coffee, milk, saltwater, lemon or tomato juice to remain in
contact with enamel parts (i.e. inside the oven).
• Do not use abrasive cleaners or powders that will scratch the surface of the stainless
steel and the enamel.
• Do not attempt to repair the internal workings of your oven.
• VEBIG 24 SS model only: Do remove the protective film before the first use.
• Fire risk! Do not store flammable material in the oven.
FOR YOUR SAFETY
Under no circumstances should any external covers be removed for servicing or
maintenance except by suitably qualified personnel.
햵

15
WARNING!
THIS APPLIANCE HAS TO BE INSTALLED BY A QUALIFIED INSTALLER.
Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a
qualified installer, service agent, or the gas supplier.
I PORTANT: The use of suitable protective clothing/gloves is recommended when handling, installing of this appliance.
CAUTION !
Some cabinets and building materials are not designed to withstand the heat produced by the normal safe operation of the appli-
ance. Dis-coloration or damage, such as delamination, may occur.
To prevent possible damage to cabinets and cabinet finishes, use only materials and finishes that will withstand temperature up to
190°F (88°C), and that are moisture resistant.
When cabinets are covered with laminates, an appropriate heat-resistant adhesive must be used.
Consult your cabinet manufacturer for proper specifications.
The cabinet must have solid sides, back and bottom. The bottom must be solid either at floor level or with the bottom edge of the
cutout. Any openings around the gas or electrical outlets must be sealed. All cabinet openings must be sealed at the time of instal-
lation to prevent drafts. Drafts will affect safe use of the oven.
TOOLS NEEDED FOR INSTALLATION (NOT SUPPLIED WITH THE APPLIANCE)
Screwdriver Wrench T-handle wrench Tape measure
Angled
hexagon key Pencil
Adjustable
pliers
Adjustable
wrench
Suitable protective
gloves Drill
INSTALLATION INSTRUCTIONS

16
GENERAL INFORMATION
1. Inst ll tion must conform with loc l codes or, in the
bsence of loc l codes, with the National Fuel Gas Code,
ANSI Z223.1-L test Edition.
2. Inst ll tion in m nuf ctured (mobile) home: inst ll tion must
conform with the anufactured Home Construction and
Safety Standard, Title 24 CFR, Part 3280 [formerly the
Federal Standard for obile Home Construction and
Safety, Title 24, HUD (Part 280)] or, when such st nd rd is
not pplic ble, the St nd rd for anufactured Home
Installations, ANSI/NCSBCS A225.1, or with loc l codes
where pplic ble.
3.Inst ll tion in Recre tion l P rk Tr ilers: inst ll tion must
conform with st te or other codes or, in the bsence of such
codes, with the St nd rd for Recreational Park Trailers,
ANSI A119.5.
4. WARNING!!
This appliance shall not be used for space heating. This
information is based on safety considerations.
5. AlI openings in the wall behind the appliance and in the floor
under the appliance shall be sealed.
6. Keep appliance area clear and free from combustible materi-
als, gasoline, and other flammable vapors.
7. Do not obstruct the flow of combustion and ventilation air.
8. Disconnect the electrical supply to the appliance before ser-
vicing.
9. When removing appliance for cleaning and/or service;
A. Shut off gas at main supply.
B. Disconnect AC power supply.
C. Disconnect gas line to the inlet pipe.
D. Carefully lift appliance out of cabinet cutout.
CAUTION: Use care in handling.
10. Electrical Requirement
Electrical installation should comply with national and local
codes.
11. Air Supply and Ventilation
The installer must refers to local/national codes.
12. Gas anifold Pressure
Natural gas - 4.0” W.C.P.
LP/Propane - 11.0” W.C.P.
13. The misuse of oven door (e.g. stepping, sitting, or leaning on
them) can result in potential hazards and/or injuries.
WARNING!!
ELECTRICAL GROUNDING INSTRUCTIONS
The oven must be electrically grounded in accordance with
local codes or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA No 70-latest edition.
Installation should be made by a Iicensed electrician.
FOR PERSONAL SAFETY, THIS APPLIANCE UST BE
PROPERLY GROUNDED.
This appliance is equipped with a three-prong grounding plug
for your protection against shock hazard and should be
plugged directly into a properly grounded socket. Do not cut
or remove the grounding prong from the plug.
For personal safety, this appliance must be properly
grounded.
Do not under any circumstances cut or remove the third
(ground) prong from the power plug.
REPLACE ENT PARTS
Only authorized replacement parts may be used in performing
service on the oven. Replacement parts are available from
factory authorized parts distributors. Contact the nearest parts
distributor in your area.

17
22" 11/64
(563.2 mm)
(550 mm)
21"5/8
25/32"
(20mm)
23" 3/16withgas pressure
regulatorfitted
21" 49/64
24"
(609.5 mm)
(553 mm)
24"
(609.5 mm)
(589.5 mm)
Fig. 5.1
Fig. 5.2
nstallat on 
This oven may be installed to 24" minimum (609.5 mm) wide
cabinets
Oven dimensions (fig. 5.1):
• width = 24" (609.5 mm);
• depth = 21" 5/8 (550 mm);
• depth = 23" 3/16 (589.5 mm) with gas pressure regulator
fitted;
• height = 24" (609.5 mm);
• oven frame depth = 25/32" (20 mm);
Cutout dimensions (fig. 5.3):
• width = 22" (559 mm);
• depth = 23" (584 mm) minimum from front corner of cutout;
• height = 23" (584);
I PORTANT NOTE: THE BOTTO OF CUTOUT SHALL
BE AT LEAST 22" 5/8 (574.4 mm) FRO THE FLOOR. DO
NOT INSTALL THE OVEN BENEATH THE WORK
COUNTER.
On the lover side, the oven must lay on a support standing
the oven weight. Oven support surface MUST be solid.
All openings in the wall or floor where the oven is to be
installed MUST be sealed. Oven location should be away
from strong draft areas, such as windows, doors and strong
heating vents.
For SAFETY CONSIDERATIONS the oven S ALL BE FAS-
TENED to the cabinet with four (4) SUITABLE screws (not
supplied with the unit) through the holes in the trim (see fig.
5.2). The unit should be leveled properly before being
secured to the cabinet.
Taking care NOT to lift the
oven by the door handle.
INSTALLATION TO THE CABINET

18
10" 1/16
(255.8 mm)

=

=

20" 35/64 
(522 mm)

20" 5/16 
(515.5 mm)

minimum
1" 1/4
(31.8 mm)

minimum
7" 7/8
(200 mm)
=

=

23"
(584mm)
minimum
cut-out depth
minimum height
from the floor
22" 5/8
(574.4 mm)
cut-out height
23"
(584 mm)
cut-out width
22"
(559 mm)
Fig. 5.3
Fig. 5.4
햶
Provide a hole for
gas connection to
1/2" diameter
pipe fitting. Provide hole
for electrical
connection in
this area
Area for
electrical
connection
G s line opening:
Provide a suitable hole on the bottom of
cutout. The centre of hole shall be 10"
1/16 (255.8 mm) from the centre of
cutout to the left side and 20" 35/64 (522
mm) from the front corner of cutout to
the back.
Grounded outlet:
The electric cord with 3-prong ground
plug has a length of 48” (1220 mm).
Grounded outlet should be located in an
area 7" 7/8 (200 mm) below the bottom
of cutout and only on the right side of the
cabinet (from the centre to the right side
of the cabinet).
A suitable hole has to be provided on the
bottom of the cutout, in an area posi-
tioned on the right rear corner (1" 1/4
[31.8 mm] maximum from the right side
of cutout and from the rear corner to
maximum 20" 5/16 (515.5 mm) from the
front corner of cutout), to pass the appli-
ance cable.

19
Explos on Hazard
Use a new CSA or UL approved
gas supply line.
Install a shut-off valve.
Securely tighten all gas connec-
tions.
If connected to LP, have a quali-
fied person make sure gas pres-
sure does not exceed 14" water
column.
Examples of a qualified person
include licensed heating per-
sonnel, authorized gas compa-
ny personnel, and authorized
service personnel.
Failure to do so can result in
death, explosion, or fire.
Gas supply line
Shutoff valve
“open” position
To oven
Fig. 6.1
All gas connections must be made according to national and local codes. This gas
supply (service) line must be the same size or greater than the inlet line of the
appliance. Sealant on all pipe joints must be resistant to the action of LP/Propane
gas.
The oven is equipped for the use with NATURAL gas. It is design-certified by CSA
International for NATURAL and L.P. gases with appropriate conversion.
The model/serial rating plate, located on the back of the oven, has information on
the type of gas that can be used. If this information does not agree with the type of
gas available, check with the local gas supplier. See page 23 for L.P. gas conversion
inctructions.
1. anual Shut-off Valve (fig. 6.1):
A manual shut-off valve must be installed in an accessible location in the gas line
external to the appliance for the purpose of turning on or shutting off gas to the
appliance (In Massachusetts such shutoff devices should be approved by the Board
of State Examiners of Plumbers & Gas Fitters). This valve should be located in the
same room as the oven and should be in a location that allows ease of opening and
closing (in a position where it can be reached quickly in the event of an emergency).
Do not block access to the shutoff valve. The valve is for turning on or shutting off
gas to the appliance.
2. Pressure Regulator:
a) All heavy duty, commercial type cooking equipment must have a pressure regulator
on the incoming service line for safe and efficient operation, since service pressure
may fluctuate with local demand.
Before installing the regulator mount the 3/8” NPT (conical) male connector to the
regulator (see picture 6.2a). Gasket supplied have to be placed between 3/8” NPT
(conical) connector/manifold male pipe fitting (see picture 6.2b).
The regulator supplied with this oven must be installed before any gas connections
are made.
Use supplied pressure regulator only.
gas connect on 

20
햷
햳
PRESSURE REGULATOR INSTALLATION
LOCK
Arrow
STEP 1
Mount the 3/8” NPT (conical) male connector to the pressure
regulator and tighten by using a wrench.
Do not over tighten the connector.
Over tightening may crack regulator.
STEP 2
Assemble the 3/8” NPT connector + pressure regulator group to the manifold interposing the gasket supplied. The regulator
cover must be oriented toward the back of the cabinet.
IMPORTANT: use two spanners to tighten the connection.
Regulator cover
Fig. 6.2a
Fig. 6.2b