Vertiv DCE E42611 User manual

DCE™ Rack System
Installer/User Guide

Technical Support Site
If you encounter any installation or operational issues with your product, check the pertinent section of
this manual to see if the issue can be resolved by following outlined procedures. For additional assistance,
visit https://www.VertivCo.com/en-us/support/

TABLE OF CONTENTS
1 Important Safety Instructions 5
2 What’s Included 7
3 Installation 9
3.1 Receiving, Unpacking, andRemovingtheDCERackfromthePallet 9
3.2 Loading Equipment 9
3.3 Operating Door Handle 9
3.4 Reversing the door handle 9
3.5 Door Removal and Attachment 11
3.6 Field-reversible Front and Rear Doors 12
3.7 Side Panel Removal 13
3.8 Top Panel Mounting 13
3.9 Top Panel Mounting for the E426112DR 14
3.10 Bottom Panel Mounting for the E426112DR 15
3.11 Casters and Leveling Feet 16
3.11.1 Leveling Feet Adjustment 20
3.12 Mounting Rail Adjustment 20
3.13 PDU/Cable-management Brackets 22
4 Optional Accessories 23
4.1 Vertical Cable Manager Kit: E846015 23
4.2 Horizontal Front-to-rear Cable Manager: E11015/E12015 25
4.3 Front-to-rear Cable Trough: E811015/E812015 25
4.4 Adjustable Ladder-rack Bracket: ELRB016 26
4.5 Overhead cable trough: E6016/7016/8016 28
4.6 Exhaust Chimney: E1832014/E3246014 29
4.7 Vertical-airflow Baffle with Brush Kit for800-mmWRack:E48801/E428014/E458014 29
4.8 Vertical Airflow Baffle with Brush Kit for700-mmWRack:E487014/E427014/E457014 31
4.9 Vertical-airflow Baffle withBrushKitandVerticalCableManager 32
4.10 Switch Kit for Side-to-side Cisco Switch for1000-mmWRack:E7009014/E7018014 33
4.11 Switch Kit for Side-to-side Cisco Switch
for800-mmWRack:E650304/E6506014/E9513014/E6513014 36
4.12 Baying Gasket Kit: E4013 38
4.13 Baying Kit: E9013 39
Vertiv | DCE Installer/User Guide | 3

Vertiv | DCE Installer/User Guide | 4

1 IMPORTANT SAFETY INSTRUCTIONS
Save These Instructions
This manual is provided to prevent service personnel from committing an act that results in the risk of fire,
electric shock, or injury to persons. Only trained service personnel should receive, unpack, and assemble
the DCE Racks. In addition, only trained service personnel should install equipment in racks.
Improper handling and use of the DCE Rack could result in equipment damage, serious injury, or possible
death.
WARNING: Only trained service personnel should be used to remove the rack from the pallet. Also, be
sure you have a sufficient number of service personnel. Do not attempt to move racks by yourself.
WARNING: All wiring and electrical circuits must be in compliance with National and Local electric
codes. Only ITE (Information Technology Equipment) bearing the safety compliance mark of a NRTL
should be installed inside the DCE Rack. NRTL compliance marks include UL®, C-UL®, CSA®, ETL®,
TUV®, and CE.
WARNING: Be sure to read and follow all individual manufacturer equipment manuals for safety and
installation instructions.
WARNING: Proper spacing is required when installing electrical equipment to avoid electrical shock.
Maintain minimum spacing between the accessories and components and the computer rack assembly
for safe operation of the equipment when installed in accordance with the National Electric Code
ANSI/NFPA 70-1999.
Vertiv | DCE Installer/User Guide | 5

Vertiv | DCE Installer/User Guide | 6
This page intentionally left blank.

2 WHAT’S INCLUDED
•DCE unit (assembled)
•Keys as needed (depending on configuration)
•(50) M6 cage nuts (3/8” square) and M6 screws
•Baying hardware
•Edge grommet
•This Installer/User Guide
This manual applies to the following pre-configured and applicable configured DCE racks:
PART NO. RU W (MM) D (MM)
E24611 24 600 1100
E42611 42 600 1100
E42612 42 600 1200
E426112DR 42 600 1100
E42711 42 700 1100
E42712 42 700 1200
E42811 42 800 1100
E42812 42 800 1200
E42112 42 1000 1200
E45611 45 600 1100
E45612 45 600 1200
E45711 45 700 1100
E45712 45 700 1200
E45811 45 800 1100
E45812 45 800 1200
E45112 45 1000 1200
E48611 48 600 1100
E48612 48 600 1200
E48711 48 700 1100
E48712 48 700 1200
E48811 48 800 1100
E48812 48 800 1200
E48112 48 1000 1200
DCE static weight capacity: 3000 lbs.
DCE dynamic weight capacity: 2500 lbs.
Vertiv | DCE Installer/User Guide | 7

Vertiv | DCE Installer/User Guide | 8
This page intentionally left blank.

3 INSTALLATION
3.1 Receiving, Unpacking, andRemovingtheDCERackfromthePallet
Inspect and report any damage before receiving. Unpack the rack by carefully removing the corrugated
carton and corners. Avoid damaging the rack when removing packaging.
WARNING: Only trained service personnel should be used to remove the rack from the pallet. Also, be
sure you have a sufficient number of service personnel. Do not attempt to move racks by yourself.
WARNING: Be careful when moving racks before installation. Sudden stops and starts, excessive
force, obstructed routes, and uneven floor surfaces may cause the rack to topple over.
3.2 Loading Equipment
WARNING: Only install equipment after the DCE Rack has been properly secured. Do not move the rack
assembly while loaded.
Once in place at the desired/intended location, deploy the leveling feet for maximum stability.
Rated or maximum-load capacity for the DCE Rack is 3000 pounds on the floor or on leveling glides.
To maintain a uniform distribution of the mechanical load in the DCE Rack, load the heaviest equipment
first, at the bottom of the DCE Rack and load the lighter units at the top.
3.3 Operating Door Handle
The door swing handles have been installed at the manufacturer. No additional assembly is required. To
operate the swing handle, lift up at the bottom of the handle then swing the handle to the right to open.
The handle must be kept in this position to close the door. Return the handle to the initial position and
use the key provided to lock the handle. The lock on the side panels will accept the same key.
The swing handles and doors are reversible. See "Reversing the door handle" below.
3.4 Reversing the door handle
1. Remove the Phillips-head bolt from the swing-handle retainer on the inside of the door.
2. Tilt the handle outward and lift up to remove it from the door.
3. Remove the Phillips-head cam retaining bolt, rotate the cam 180° and re-install cam retaining
bolt.
Vertiv | DCE Installer/User Guide | 9

4. After reversing the door, reinstall the swing handle by sliding downward into door and tilting
inward.
5. Re-install swing-handle retainer and Phillips head bolt.
Figure 3.1 Door handle components
ITEM DESCRIPTION
1 Phillips-head bolt
2 Phillips-head cam-retaining bolt
3 Cam
4 Retainer
Vertiv | DCE Installer/User Guide | 10