Vestamatic VRS Transmitter 5C User manual

Subject to modifications.© Vestamatic GmbH 1/2
G
Art.-Nr.: 6000 002 GB 0819 A04 • Vestamatic GmbH • Dohrweg 27 • D-41066 Mönchengladbach • www.vestamatic.com
VRS Transmitter 5C / 10C
VRS Transmitter 5C
VRS Transmitter 10C
Installation and Operating Instructions
VRS Transmitter 5C Art.-no.: 01580070
VRS Transmitter 5C Nero Art.-no.: 01580075
VRS Transmitter 10C Art.-no.: 01580080
VRS Transmitter 10C Nero Art.-no.: 01580085
5/10 channel transmitter in Vestamatic Radio System (VRS).
G
6000 002 GB 0819 A04
1. Safety precautions
ATTENTION!
– Check the transmitter for signs of mechanical damage after
unpacking. If you notice any shipping damage, do not start
up the transmitter and notify your supplier immediately.
– The transmitter should only be used for the purpose speci-
fied by the manufacturer (refer to the operating instructions).
Any changes or modifications thereof are not permissible
and will result in loss of all warranty claims.
– This device contains a pollutant battery. The end user must
recycle all used batteries in accordance with regulation
91/157/EWG. Disposing of the batteries in household waste
is strictly forbidden.
Ä
2. Short description
Universal 5 and 10 channel hand-held transmitter for
control of VRS radio receivers
Intuitive channel selection with channel selection buttons
5. Functional description
The hand-held transmitter is a radio transmitter for controlling VRS radio
receiver. By pushing the button, the VRS code is transmitted and the con-
nected VRS radio receiver is switched according to their selected mode.
3. Technical data
Article VRS Transmitter/ 5C 5C Nero 10C 10C Nero
Art.-no.:
01580070 01580075 01580080 01580085
Radio frequency: 868 MHz
Transmitter power: 10 dBm
Operating temperature: 0 °C (32 °F) to +40 °C (104 °F)
Protection degree: IP 30
Dimensions (L × W × D): 145 × 36 × 11 mm
Battery: 3V Type CR2032
6. Installation
(Wall bracket for VRS Transmitter 5 and 10 / Art.-no.: 01580140)
The wall bracket can be found in the accessory program (not included in
the scope delivery).
To mount the wall bracket, use the enclosed screws and dowels.
Attach the wall bracket as shown in Figure 1 below.
The VRS transmitter is placed into the wall bracket as pictured in Figure 2.
Fig. 1
Fig. 2
These products comply with the essential requirements. These
products are conform to the basic requirements of the European
Radio Equipment Directive 2014/53 /EU. The Declaration of
Con-formity concerning these products are available on our
website: www.vestamatic.com
4. Declaration of conformity
WARNING!
– Inappropriate use or ingestion of the lithium battery can result
in serious injury or death.
– Keep batteries away from children.
– In the event of faulty assembly or damage to the housing, the
product must not be used and kept out of reach of children.
– If you think that batteries have been swallowed or are in any
part of the body, seek immediate medical attention.
Ä

Subject to modifications.© Vestamatic GmbH 2/2
G
Art.-Nr.: 6000 002 GB 0819 A04 • Vestamatic GmbH • Dohrweg 27 • D-41066 Mönchengladbach • www.vestamatic.com
VRS Transmitter 5C / 10C
8. Programming
The transmitter is suitable for all VRS receiver (Vestamatic Radio System).
For more information, please refer to the manual of the used radio receiver.
9. Replacing the Battery
If the hand-held transmitter’s range is dramatically reduced and the LED
indicator is weakly lit, you will need to replace the hand-held transmitter’s
battery.
1. To do this, use a suitable Phillips screwdriver (size 0) to remove the
screw on the back of the hand-held transmitter.
2. Then, press back the snap tab on the top section and remove the
bottom section of the hand-held transmitter.
3. Replace the CR 2032 type battery.
Make sure you insert the new battery correctly, the positive pole
has to be visible.
4. Then reassemble the housing by following the instructions in the reverse
order.
10. Instructions for radio receiver
ATTENTION!
Radio transmission is not suitable for safety operations,
such as emergency-stop, emergency call or warning signals.
Ä
Signals are transmitted across the Europe-wide approved 868 MHz fre-
quency band. The radio transmission range largely depends on the con-
structional circumstances of the building. If other adjacent radio devices are
simultaneously sending signals, mutual interferences cannot be debared.
Such interferences can also affect individual units of a group of receivers.
Observing the following instructions will minimize these interferences:
– Avoid to mount radio receivers onto or adjacent to metal surfaces.
– Maintain minimum 50 cm clearance to consumer loads, such as micro-
wave ovens or TV sets.
– Keep a minimum clearance of 50 cm between each mounted radio
receiver.
– Keep a minimum clearance of 50 cm between a radio receiver and a
radio transmitter.
If a radio-transmitted command cannot be clearly detected, the command
execution will be suppressed by means of an integrated automatic safety
function. The command must then be issued again.
The disposal of electrical equipment and batteries in household waste
is strictly forbidden.
The symbol (dustbin crossed out, in line with WEEE Appendix IX)
indicates separate collection of electrical and electronic products in
EU countries. Do not dispose of the device or battery in your house-
hold waste. Ask your town or local council about the return and col-
lection systems available in your area to dispose of this product.
É
11. Disposal of waste
7. Description of radio remote control VRS
A. LED indication of selected channel of the
transmitter.
To change channel:
Briefly press one of the two channel selection
buttons
+
or . The LEDs show the current
selected channel. Use the button
+
or to
select the channel. The selection is saved im-
mediately.
PROG. button
at the back side
Function + Programming Transmitter Radio Remote Control VRS
B. VRS Transmitter 5C (Art.-no. 01580070):
Switching from AUTO to MANUAL mode
(receiver-dependent).
Press and hold the button and then press
the
+
button for 3 seconds until the operat-
ing mode switches. The LEDs AUTO or MAN
and the channels will light up briefly.
VRS Transmitter 10C (Art.-no. 01580080):
Left LED indication channel 1–5
Right LED indication channel 6–10
C. Manual control buttons.
Channel 1– 10 = Motor / Shade / Lighting
Button ON/UP = Q
Button STOP
Button OFF/DOWN = q
B.
A.
C.