Vestax PMC-07ProD User manual

(a) CURVE PATTERN SWITCH
(b) C.F. FINE CONTROL
NORMAL NORMAL NORMAL
REVERSE
CURVE CURVE
I.F. REV. I.F. REV.C.F. REV.
PHONES
REVERSE REVERSE
PROFESSIONAL MIXING CONTROLLER
PGM 1 CROSS FADER PGM 2
PROFESSIONAL MIXING CONTROLLER
FUNCTIONS
The replacement crossfader unit for PMC-07ProD is
"CF-X".
"CF-05PRO", "CF-PCV" cannot be substituted in this
mixer.
OWNER'S MANUAL
Vestax Corporation
1-18-6 Wakabayashi, Setagaya-ku, Tokyo 154-0023 Japan
Phone [phone] Fax [phone]
Vestax (Europe) Ltd.
Unit 5 Riverwey Industrial Park Alton Hampshire GU34 2QL England, U.K.
Phone [phone] Fax [phone]
Web : www.vestax.co.uk
Vestax Technical Center of America
8489 W. Third Street Ste. 1044 Los Angleles, CA 90048
Phone [phone] Fax [phone]
21
PHONES
MAX
LO MID H I
+6
-24
+12
0
-12
dB dB
LO H I LO MID H I
LINE 2
PHONO 2
MIN
MAXMIN MAXMIN
GAIN
REVERSE
NORMAL
EQ EQEQ
BALANCEPAN BALANCE
SUB MIC MAIN MIC
LRLRLR
MAX
MAX
MIN MIN
MAX
MIN
PGM 2PGM 1
MAXMIN
MASTER
CUE
GAIN POWER
LEVEL LEVEL
LEVEL
PGM 1
PGM REV
MIC MASTER
MONITOR SELECT
SESSION MIX
PGM 2
PGM 1 PGM 2 MONITOR LEVEL
C.F. MONITOR
+6
+3
0
-3
-6
-10
-20
LINE 1
PHONO 1
CURVE PATTERN
MAX
MIN
C.F. FINE
DIGITAL FADER CONTROL
1
2
34
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
PROFESSIONAL MIXING CONTROLLER
TOP PANEL
Curve pattern switch (a) selects the crossfader curve
pattern.
Setting the C.F. FINE CONTROL to minimum, the
crossfader curve is most sharp, moving the control
clockwise, towards max, gradually reduces the
sharpness of the curve (b).
FRONT PANEL
INPUT FADER CURVE adjustments for PGM1 + PGM2.
Thank you for purchasing the VESTAX PMC-07ProD. Please read this owner's manual carefully before you start to
use in order to understand fully how it to operate your new mixer.
CONGRATULATIONS!
FEATURES
The new Vestax Digital Fader System consists of coils and a permanent magnet. There is no contact between
these parts.Therefore, neither the element or magnet gets degraded or damaged even after hard usage.
Unlike an optical type fader, the digital fader system does not get effected even by liquid spills or dusts.
Control of the fader curve by a complete digital signal system, enabling creation of sharp edges in the curve
pattern.

1
2
34
1
2
34
1
2
34
1
2
34
PRE-SET CURVE
SHAPE 1:
SHAPE 2:
SHAPE 3:
SHAPE 4:
C.F.POSITION
C.F.POSITION
C.F.POSITION
Using curve pattern switch,select the crossfader curve pattern from SHAPE1-4,to set the cross-
fader pattern.
As this curve shape is very sharp,it is
used for hard scratch play.
Setting C.F. FINE CONTROL to
minimum,the curve sharp is most
sharp.As the switch moves closer to
max,the curve sharpness reduces.
This curve shape is "A" type curve.
In this position,switching C.F.FINE
CONTROL from MIN to MAX, the
crossfader curve shape changes
from slow slope curve to sharp slope
by 8 steps.
This curve shape is rectangle wave type.Moving the crossfader from right to left or from
left to right,it performs like a "transformer scratch".Switching C.F. FINE CONTROL,the 8
patterns crossfader curve shape can be selected.It enables selection of the 8 patterns of
curve shape as fig 1- fig 8 below.
C.F. FINE CONTROL : MIN
C.F. FINE CONTROL : MIN
C.F. FINE CONTROL : MIN
C.F. FINE CONTROL : MAX
C.F. FINE CONTROL : MAX
C.F. FINE CONTROL : MAX
C.F.POSITION fig-3 fig-4fig-1
C.F. FINE CONTROL : MIN
fig-8
C.F. FINE CONTROL : MAX
fig-7fig-6fig-5
fig-2