VEVOR OVERHEAD GARAGE RACK User manual

ASSEMBLY INSTRUCTION MANUAL
OVERHEAD GARAGE RACK

Have product questions? Need technical suppo? Please feel free to contact us:
CustomerSe[email protected]
NEED HELP? CONTACTUS!
This is the original instruction, please read all manual instructions carefully before
operating. VEVOR resees a clear interpretation of our user manual. The appear-
ance of the product shall be subject to the product you received. Please forgive us
that we won't inform you again if there are any technology or software updates
on our product.
01
OVERHEAD
GARAGE RACK

02
-Install into Wood Joists only
-Distribute weight evenly
-Opposite ends may come loose when installing side beams
-Objects can fall o the rack after being loaded
WARNINGS
Tools Required (Not Included)
1X 2X

03
THIS IS A DO IT YOURSELF (DIY) PROJECT. DO NOT ATTEMPT THIS INSTALLATION
WITHOUT A BASIC UNDERSTANDING OF THE CONTENTS IN THESE ASSEMBLY
INSTRUCTION. IF YOU ARE NOT CONFIDENT WITH LOCATING AND ANCHORING
THE STORAGE RACK TO THE CEILING JOISTS, DO NOT ATTEMPT THIS INSTALLA-
TION WITHOUT SOMEONE WHO IS.
BE CAREFUL THESE INSTRUCTIONS, WARNINGS AND NOTES DO NOT REPLACE
YOUR SOUND JUDGEMENT AND DECISION MARKING, IF, FOR ANY REASON, YOU
FEEL THE QUALITY OF YOUR CEILING STRUCTURE IS IN QUESTION, DISCONTINUE
THE INSTALLATION PROCESS IMMEDIATELY. USE THE STORAGE RACK WISELY AND
ENJOY YOUR NEW FOUND SPACE!
4ftx8ft Frame 600 LBS 4ftx6ft Frame 550 LBS
3ftx8ft Frame 600 LBS 3ftx6ft Frame 550 LBS
2ftx8ft Frame 400 LBS 2ftx6ft Frame 300 LBS
4ftx4ft Frame 300 LBS
WARNING: This weight limit is based on a statically loaded storage rack anchored to
a wood framed garage. This installation is intended for a wood frame home, if your
home is steel framed, stop the installation.
NOTE: Loading the overhead storage rack evenly. Load heavy objects nearest the
veical posts and light objects nearest the center. Do not climb on or hang from the
storage rack. Routinely inspect the storage rack to ensure rivets and wire decking
units are seated properly. The storage rack may experience some deection the
closer the maximum load is approached.
1. It is forbidden to car people and pets.
2. It is forbidden to use the platform as electric, pneumatic and hydraulic
appliances.
3. It is forbidden to shake the storage shelves violently in any form.
WARNING
WARNING, DO NOT EXCEED THE WEIGHT LIMITS

04
4ft x 8ft Unit：
8 Veical Posts
2 Side Beams
4/2 C Channel Beams
3 Center Suppos
4 Ceiling Brackets
4 Wire Decking Units
4 Diagonal Brace
1 ceiling drilling
positioning paper
1 Hardware Bag
4 Hooks
4ft x 6ft Unit：
8 Veical Posts
2 Side Beams
4/2 C Channel Beams
2 Center Suppos
4 Ceiling Brackets
3 Wire Decking Units
4 Diagonal Brace
1 ceiling drilling
positioning paper
1 Hardware Bag
2 Hooks
3ft x 8ft Unit：
8 Veical Posts
2 Side Beams
4/2 C Channel Beams
3 Center Suppos
4 Ceiling Brackets
4 Wire Decking Units
4 Diagonal Brace
1 ceiling drilling
positioning paper
1 Hardware Bag
2 Hooks
3ft x 6ft Unit：
8 Veical Posts
2 Side Beams
4/2 C Channel Beams
2 Center Suppos
4 Ceiling Brackets
3 Wire Decking Units
4 Diagonal Brace
1 ceiling drilling
positioning paper
1 Hardware Bag
2 Hooks
2ft x 8ft Unit：
8 Veical Posts
2 Side Beams
4/2 C Channel Beams
1 Center Suppo
4 Ceiling Brackets
2 Wire Decking Units
4 Diagonal Brace
1 ceiling drilling
positioning paper
1 Hardware Bag
2 Hooks
2ft x 6ft Unit：
8 Veical Posts
2 Side Beams
4/2 C Channel Beams
1 Center Suppo
4 Ceiling Brackets
2 Wire Decking Units
4 Diagonal Brace
1 ceiling drilling
positioning paper
1 Hardware Bag
2 Hooks
4ft x 4ft Unit：
8 Veical Posts
2 Side Beams
2 C Channel Beams
1 Center Suppos
4 Ceiling Brackets
2 Wire Decking Units
4 Diagonal Brace
1 ceiling drilling
positioning paper
1 Hardware Bag
2 Hooks
Hardware bag ( for all racks):
8 Lag Bolt St8.0×75mm
8 Expansion Plug
21 Hex Bolt M8 x 16 with 21 Nuts & 42 Washer
13 Hex Bolt M6 x 16 with 13 Nuts & 13 Washer (for
2pcs beam connecting style only)
COMPONETS
Pictures Available on Next Page

05
Diagonal Brace
Lag Bolt
St8.0×75mm
AB
Hex Bolt
M8x16 Hex Bolt
M6x 16

06
Completing the following 1~3 steps to assemble the long C Channel beam. 2pcs
connecting beam design needed only! The whole beam design can ignore the
assembly steps on this page.
Step 1, Align the holes at the center of the 2pcs C Channel beams as seen in the
illustration (8ft size only).
Step 2, Using 4pcs M6x16 Hex bolts, 4pcs Hex nut and 4pcs Washer, assemble the C
Channel beam together on the outermost
Holes as seen in the following picture.
(Tips: to avoid alignment issues, place the remaining 2pcs M6 x 16 Hex bolts in the
center holes, as these will be used for the center suppo in a later step.)
Step 3, Repeat steps 1 and 2 for the remaining C Channel beams.
Pre-Assenbly

07
To punch holes on the ceiling more quickly and accurately, we have thoughtfully
designed the ceiling drilling positioning paper(included in the package). If necessa,
please follow the steps below:
1. First, nd the beam position on the ceiling, stick one of the long beam positioning
paper on the ceiling with double-sided tape, ensure that the two black lines at both
ends are on the beam or across the two beams, and the positioning paper is not
bent or sagging.
2. Then align the edges of the two sho beam positioning papers with the two ends
of the long beam positioning papers, and stick them on the ceiling perpendicular to
the long beam positioning papers.
Assenbly

08
3. Next, align the two ends of the last long beam positioning paper with the edge of
the sho beam positioning paper respectively, and stick it on the ceiling parallel to
the rst long beam positioning paper.
Ceiling drilling positioning paper: rst stick the positioning paper on the appropriate position of the ceiling
(diagram shown at right)，and then drill holes according to the marked position and requirements. ① ② ③ ④
Drill 2 holes on the black line, making sure they are on either side of the red line
Align the outside of the column with the red line
Drill 2 holes on the black line, making sure they are on either side of the red line
Align the outside of the column with the red line
Ceiling drilling positioning paper: rst stick the positioning paper on the appropriate position of the ceiling
(diagram shown at right)，and then drill holes according to the marked position and requirements. ① ② ③ ④
Drill 2 holes on the black line, making sure they are on either side of the red line
Align the outside of the column with the red line
Drill 2 holes on the black line, making sure they are on either side of the red line
Align the outside of the column with the red line