Via Seating Run II User manual

Run II
user guide
205 Vista Boulevard, Sparks, Nevada 89434 lPhone: 800-443-6614 lviaseating.com
table of contents
38A height adjustable arm
35C stool control mechanism
39A height adjustable roll back arm
64C/64CS control mechanism
65C synchro with side tension adjustment control
LR2 adjustable lumbar support
51A/51AG/53A adjustable height arm with 4-ways adjustable cap option
pg. 1
pg. 2
pg. 3
pg. 4
pg. 5
pg. 6
pg. 7

775 331 6001
[e-mail]
www.viaseating.com
1
Run II
user guide
38A height adjustable arm
Adjust arm height (38A):
Press “arm button” while
also pulling upward to raise
arms to desired height.
Additional Width Adjustment (Only
applies to 19AB): Pull back on the
“levers” under the arms to unlock
and extend the arms outwards.
Push forward on the levers to lock.
To put them back to normal simply
just do the opposite. Unlock (pull
back on the lever) and push the
arms back in to place, and lock the
arms by pushing the lever forward.
Arm
Button
Switch
(Lever)
Switch
(Lever)
Arm
Button

Run II
user guide
Roll back arm feature: While
pressing and holding the small
“button” toward the top front
on the silver circle, grasp the
arm and roll back to horizontal
position. Repeat to lift back to
upright position.
Arm height adjustment: While
pressing the “button”, use your
hand to raise and lower the arm
height
39A height adjustable roll back arm
Arm
Button
Arm
Button
775 331 6001
[e-mail]
www.viaseating.com
2

Additional Width Adjustment
(Only applies to 19AB): Pull
back on the “levers” under the
arms to unlock and extend the
arms outwards. Push forward on
the levers to lock.
To put them back to normal
simply just do the opposite.
Unlock (pull back on the lever)
and push the arms back in to
place, and lock the arms by
pushing the lever forward.
Optional arm cap rotation
(Only applies to 20R):
Grasp arm cap and slide
forward or back (1.5”).
Arm height adjustment:
While lifting up on the
small “switch”, use your
hand grasping the arm cap
to raise and lower the arm
height.
Optional arm cap rotation
(Only applies to 20R):
Grasp arm cap and turn left
or right to rotate a max of
15° each way.
51A/51AG/53A adjustable height arm with 4-ways adjustable cap option
Switch
(Lever)
Switch
(Lever)
Switch
(Lever)
Run II
user guide
775 331 6001
[e-mail]
www.viaseating.com
3

Run II
user guide
35C stool control mechanism
Push the
button
Push the
button
Seat height adjustment: Adjust
the seat height by lifting your
weight out of the chair and
pulling up on the “paddle”.
Proper seat height is realized
when the top of your legs are
somewhat parallel to the oor.
Back lock adjustment (single
position): Use the same paddle
as you use for the seat height
adjustment. To lock the chair in
an upright position, shift your
weight forward until the chair
is in an upright position, then
push the “button” in. To rock
(free oat) shift your weight
forward and push the button
again.
Pull up
on paddle
Unlock foot ring: press down on the
plastic “inner hub” and lift the foot
ring up to unlock it. Adjust foot ring
to desired position.
Lock foot ring: lock foot ring in
place by pressing down on “outer
foot rest” until hub is in “locked”
position.
Foot ring adjustment
35C with 11DR/11XDR
Press down
inner hub
Press down
on foot rest
Foot rest
Inner hub
Pull up
on paddle
775 331 6001
[e-mail]
www.viaseating.com
4

775 331 6001
[e-mail]
www.viaseating.com
5
Seat height adjustment: Adjust
the seat height by lifting your
weight out of the chair and pulling
up on the “right paddle”. Proper
seat height is realized when the
top of your legs are somewhat
parallel to the oor.
Back tilt lock adjustment
(3 position): Rotate “left knob” right
to lock in position. Rotate knob left
to unlock and free oat. Use own
back tension to push against back of
chair and release back from chair to
nd desired position.
Back tension adjustment: Rotate
“right knob” right to increase
tilt tension. Rotate knob left to
decrease tilt tension.
64C/64CS stool control mechanism
Unlock foot ring: press down on
the plastic “inner hub” and lift the
foot ring up to unlock it. Adjust foot
ring to desired position.
Lock foot ring: lock foot ring in
place by pressing down on “outer
foot rest” until hub is in “locked”
position.
Foot ring adjustment
64CS with 11DR/11XDR
Press down
inner hub
Press down
on foot rest
Foot rest
Inner hub
RightLeft
RightLeft
Right
paddle
Left
Knob
Right
Knob
Right
Knob
Left
Knob
Pull up
right paddle
Run II
user guide

Run II
user guide
775 331 6001
[e-mail]
www.viaseating.com
6
Seat slider: Pull up on “left”paddle
while shifting your weight forward to
move your seat forward or backward
to move your seat back.
Seat height adjustment: Adjust the
seat height by lifting your weight out
of the chair and pulling up on the
“right”paddle. Proper seat height is
realized when the top of your legs are
somewhat parallel to the oor.
Back tilt lock adjustment (3
position): Rotate left “knob”
right to lock in position. Rotate
knob left to unlock and free
oat. Use own back tension to
push against back of chair and
release back from chair to nd
desired position.
Back tension adjustment:
Rotate “knob” right Increase
tilt tension. Rotate knob left
to decrease tilt tension.
Right
to lock
Left
to unlock
65C synchro with side tension adjustment control
Right paddle
Pull up
right paddle Pull up
left paddle
Left paddle
RightLeft
Right
Knob
Right
paddle
Left
Knob
Left
Knob

775 331 6001
[e-mail]
www.viaseating.com
7
Run II
user guide
LR2 Run II mesh adjustable lumbar support
(optional): lumbar position adjustment. From the
seated position, use a hand to make adjustments
by engaging the small, black lumbar “adjustment
lever”. Slide the lever up to move the lumbar
support up. Slide the lever down to move the
adjustable lumbar support down.
Adjustment
lever
(Back side of chair)
LR2 adjustable lumbar support