Vicon XX214-20-03 User manual

www.vicon-security.com
XX214-20-03
Surveyor® HD Series Network
Camera Domes
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the
operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed
to be used in life-critical situations and must not be used for this purpose.
Vicon Industries Inc.
Tel: [phone] Fax: [phone] Toll Free: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300
Document Number: 8009-8214-20-03
Product specications subject to change without notice.
Issued: 1013
Copyright © 2013 Vicon Industries Inc. All rights reserved.
Quick Guide

Quick Operation Guide | 1
Surveyor HD Camera Dome
Quick Operation Guide
This manual provides a quick overview for the operation of the Surveyor®
HD Series of Camera Domes. Refer to the complete manual, XX214-0X
(installation) and XX214-4X (web browser), for complete details on
installation, setup and operating details.
The Surveyor HD is a compact network dome comprised of a
camera/lens and pan/tilt drive in an attractive covert enclosure. Surveyor
HD is sold in a variety of prepackaged configurations with choices in
environment, mounting configuration, and lower dome types.
The Surveyor HD supports high-profile H.264 or M-JPEG compression.
The dome supports ONVIF open architecture connectivity to enable
integration into third party software recording solutions, as well as Vicon’s
ViconNet.
The Surveyor HD is designed for easy installation and serviceability. The
entire drive assembly simply snaps into the housing. When removed, the
mechanism retains all programmed functions in its on-board memory.
The customer interface board snaps down for easy access and the PCB
provides removable terminal blocks for simple wiring connections. Power
to the indoor units can be provided by PoE+ (Power over Ethernet Plus);
outdoor units require 24 VAC. The Surveyor HD includes a high-definition
1.3 or 2.0 megapixel day/night camera with wide dynamic range (WDR)
and digital noise reduction (DNR/FNR).

2| Quick Operation Guide
Installation
In-Ceiling

Quick Operation Guide | 3
Pendant

4| Quick Operation Guide
Pressurized

Quick Operation Guide | 5
Wiring and Setup
CONNECTOR/PIN
NUMBER
CONNECTOR TYPE CONNECTOR/PIN LABEL SIGNAL NAME
TERMINAL BLOCK POWER (TB2)
TB2-1 AC+ Hot
TB2-2 AC- Neutral
TERMINAL BLOCK ALARM (TB1)
TB1-1 ALARM 1 Alarm I/O 1
TB1-2 Ground
TB1-3 ALARM 2 Alarm I/O 2
TB1-4 Ground
TB1-5 ALARM 3 Alarm I/O 3
TB1-6 Ground
TB1-7 ALARM 4 Alarm I/O 4
TB1-8 Ground
TERMINAL BLOCK COMM/RELAY (TB5)
TB5-1 VSS Ground
TB5-2 CRelay, common
TB5-3 NO Relay, normally open
TB5-4 NC Relay, normally closed
RJ-45 LAN (J6)
J6-1 Transmit +
J6-2 Transmit -
J6-3 Receive +
J6-4 PoE spare
J6-5 PoE spare
J6-6 Receive -
J6-7 PoE spare
J6-8 PoE spare
1/8-IN. PHONO AUDIO (J9)
J9 J9 Audio In

6| Quick Operation Guide
Setting the DIP Switches
There are two DIP switches that must be set on the Surveyor HD. One is
on the Communications Interface (CI) board and one on the Main board.
SW1 4-position DIP switch is on the Communication Interface (CI) board.
For SW1 all poles should be set to OFF (default).
DIP Switch Location on CI Board
Caution
Changing the positions on the DIP switch on the Main board should only
be done by a qualified person. Position 1 is used only if it is necessary to
force the unit into default setup if network or system connections are lost.
Be sure to reset this switch back to the OFF position before the next
power up to avoid a constant return to defaults, resulting in not being able
to enter the camera’s IP to use the Web Browser. The camera dome is
shipped with a default static IP of 1.1.1.2.
The Main board has an 8-position DIP switch SW1. The settings for the
positions of this DIP Switch are:
Position 1 - Set Network Address. OFF = Default Position, do not
set network defaults. ON = Set k default network address (1.1.1.2);
must be reset OFF after reboot and before next power up.
Position 2 – Unused (set to OFF)
Position 3 – For factory use only. OFF is Default.
Position 4 – Unused (set to OFF)

Quick Operation Guide | 7
Position 5 – Unused (set to OFF)
Position 6 - Unused (set to OFF)
Position 7 – Set password. OFF = Default Position. ON = Reset to
default password (password); must be reset to OFF after reboot
and before next power up.
Position 8 – System Mode. OFF = Default Position, ViconNet
Mode. ON = ONVIF/NTCIP Mode.
The main board is located underneath the housing. It may be necessary
to spin the housing mechanism to see the DIP switch, located near the tilt
motor along edge of the board.
DIP Switch Location on Main Board
Communication Ports
If using NTCIP protocol, communicate to the Surveyor HD using ports
3000/UDP or 3001/TCP.
If using ONVIF, use port 8000.

8| Quick Operation Guide
Pressurized Cable Preparation
Using the prefabricated cable
Using a customer prepared cable

Quick Operation Guide | 9
Using the Web Browser Interface
Web Browser Interface
The Web Browser Interface provides a user friendly interface to configure
and control various features and functions of the Surveyor™ HD camera
dome. The interface allows the configuration of camera dome
parameters, viewing live video, using PTZ, setting administrative controls
and collecting camera dome reports and status information.
There are six (6) functional areas (pages) on the Web Browser Interface,
Camera Login, Live Video, Add/Edit Users, Settings, Maintenance and
System Information.
VMS Compatibility
The Surveyor HD Camera Dome is an ONVIF compliant open platform
product designed to be used with multiple Video Management Systems
(VMS). For initial setup when using the ViconNet VMS, refer to Appendix
A in XX214-4X for information on using the “VNSetup” discovery and
configuration application.
VMS specific tools may be necessary to use the dome with each system,
such as a Discovery Tool. Refer to their documentation.
Access the Camera
Open a browser (i.e., Internet Explorer). Enter the IP address or host
name of the camera in the Location/Address field of your browser. The
camera dome is shipped with a default IP static of 1.1.1.2; change your
PC’s IP to match the Subnet if needed.
You may be asked to load ActiveX software; click to download it at this
time.
The Surveyor HD login screen displays.