Vicon CE202D-N User manual

www.vicon-security.com
XX269-40-00
CE202D-N Network
Camera Dome
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the
operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed
to be used in life-critical situations and must not be used for this purpose.
Vicon Industries Inc.
Tel: [phone] Fax: [phone] Toll Free: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300
Document Number: 8009-8269-40-00
Product specications subject to change without notice.
Issued: 314
Copyright © 2014 Vicon Industries Inc. All rights reserved.
Quick Guide

CE202D-N Series Quick Installation Guide
1. Description
The information in this manual provides quick installation and setup procedures for the CE202D-N
Series of Camera Domes. These units should only be installed by a qualified technician using approved
materials in conformance with federal, state, and local codes. Read these instructions thoroughly
before beginning an installation. Always refer to Vicon’s website to assure you have the most up-to-
date manual, www.vicon-security.com.
The CE202D-N HD IP Camera Dome is designed for indoor security installations. This cost-effective
fixed network camera includes an integral 3.7 mm megapixel fixed lens; the 1080p resolution delivers
crisp clear images. The CE202D-N cameras are fully compatible with all ViconNet® systems; its ONVIF
certification provides an open-platform for integration into other video management systems.
The network camera provides triple-streaming video and supports H.264 compression technology.
MPEG-4 and Motion JPEG (M-JPEG) compressions are also provided, as are privacy masking and
motion detection. Installation is made easy and cost-effective with Power-over-Ethernet (PoE); the
camera also accepts 12 VDC.
• Installation Steps
Follow these steps to install the network camera on your local network (LAN):
1. Check the package contents against the list that follows.
2. Connect the network camera.
3. Set an IP address.
4. Set the password.
• Package Component
The system comes with the following components:
Camera Unit Installation CD Installation Guide Accessory Kit Template sheet
Alarm Cable Optional OSD Controller
Check your package to make sure that you received the complete system, including all components
shown above.
Note: Adapter for 12 VDC is not supplied and the optionalV920D-OSD OSD Controller can be
purchased separately.
• Contents in the installation CD
1. The CE202D-N User’s Manual
2. The SmartManager User’s Manual
3. The SmartManager Installation software
2

CE202D-N Series Quick Installation Guide
2. Installation
2.1 Camera Installation
Carefully remove the contents from the box, and verity that nothing was damaged in shipment.
1) Using the template sheet provided, make screw holes for camera on the ceiling.
2) Disassemble the camera by turning the camera cover counter-clockwise so it can be removed.
3) Secure the dome camera to the ceiling using the anchors (2x) and screws (2x) provided in the
accessory kit.
4) Reassemble the camera cover to dome camera by turning the camera cover clockwise until it locks
in place
Lock clockwise
Camera Dimension
See the diagrams below for the exact dimension. (Dimensions Unit: mm)
3

CE202D-N Series Quick Installation Guide
2.2 Connection
Connection Description
NO Name Description
1 Alarm Cable Yellow : Alarm input, Black : GND, Blue : Alarm output
2 Power Cable Cable for Power source (DC 12V)
3 Ethernet Cable Cable for Ethernet (POE)
NO Name Description
1 Factory Default Button Button for the factory default setting
2 Micro-SD Slot Micro-SD memory slot
3 Service Monitor Port Service Monitor (set to NTSC by default ; change video format from Source menu); V920D-OSD Controller (option) Communication Port,
Mono Jack
4

CE202D-N Series Quick Installation Guide
• Connecting to the RJ-45
Connect a standard RJ-45 cable to the network port of the network camera. Generally a
cross-over cable is used for directly connection to PC, while a direct cable is used for connection
to a hub.
Micro SD memory slot
Insert the SD memory card (customer supplied).
• Connecting the Power
onnect a 12 VDC power adaptor (customer supplied) to the camera.
• Connecting Service Monitor Port
The Service Monitor output port is located on the board of the dome camera and is used for easy
OSD setup.
▶ID & IP assignment
To make changes in the OSD menu, the optional OSD controller can be used to set Camera Title
and IP Address.
1. Connect the OSD Controller to the Service Monitor port of the network camera.
2. Connect Service Monitor and the Video Output port of the OSD Controller.
3. Press the SET button on the controller to access the Main Menu.
4. Change camera ID and IP address as needed. Additionally, the Name (or title) of the camera
can be changed. Use the ↑↓←→ buttons on the controller to change the parameters.
5. Select SAVE or CANCEL to exit the Main Menu.
The Video Output can also be used for easy zoom and focus control when adjusting the lens.
Video Output is restricted to 704x480 (576) resolution.
Note: The optional V920D-OSD OSD Controller can be purchased separately.
5

CE202D-N Series Quick Installation Guide
2.3 Network Connection and IP assignment
The network camera is designed for use on an Ethernet network and requires an IP address for
access. Most networks today have a DHCP server that automatically assigns IP addresses to
connected devices. By the factory default, your camera is set to obtain the IP address automatically
via DHCP server. If your network does not have a DHCP server the network camera will use
192.168.1.100 as the default IP address.
If DHCP is enabled and the product cannot be accessed, run the “Smart Manager” utility on the CD to
search and allocate an IP address to your products, or reset the product to the factory default settings
and then perform the installation again.
1. Connect the network camera to the network and power up.
2. Start SmartManager utility (Start>All programs>SmartManager>SmartManager); the main
window will be displayed, after a short while any network devices connected to the network will
be displayed in the list.
3. Select the camera on the list and click right button of the mouse. Y The pop-up menu below
displays.
4. Select Assign IP. The Assign IP window displays. Enter the required IP address.
Note: For more information, refer to the Smart Manger
User’sManual.
6

CE202D-N Series Quick Installation Guide
3. Operation
The network camera can be used with Windows® operating system and browsers. The recommended
browsers are Internet Explorer®, Safari®, Firefox®, Opera® and Google® Chrome® with Windows.
Note: To view streaming video in Microsoft® Internet Explorer, set your browser to allow ActiveX
controls.
Note: Some screens may appear different (i.e., color scheme) depending on the firmware version, but
the functionality is the same or similar.
3.1 Access from a browser
1. Start a browser (i.e., Internet Explorer).
2. Enter the IP address or host name of the Network Camera in the Location/Address field of your
browser.
3. A starting page displays. Click Live View, Playback or Setup to select corresponding web page.
4. Click Live View for the network camera’s Live View page to appear in the browser.
7

CE202D-N Series Quick Installation Guide
3.2. Access from the internet
Once connected, the network camera is accessible on your local network (LAN). To access the
network camera from the Internet you must configure your broadband router to allow incoming data
traffic to the network camera. To do this, enable the NAT-traversal feature, which will attempt to
automatically configure the router to allow access to the network camera. This is enabled from Setup
> System > Network > NAT.
For more information, please see “3.5.5 System>Network>NAT” of User’s Manual.
3.3 Setting the admin password over a secure connection
T
o
g
ain access to the product, the password for
t
he default administrator user must be set. This
is done in the “Admin Password” dialo
g
, which is
displayed when the network camera is accessed
f
or the setup at the first time. Enter your admin
name and password, set by the administrator.
Note: The default administrator username is
“
ADMIN” and password is “1234”. If the
password is lost, the network camera must be
reset to the factory default settin
g
s. See section
“
3.5 Resettin
g
to the Factory Default Settings” for
more details.
To prevent network eavesdropping when setting the admin password, this can be done via an
encrypted HTTPS connection, which requires an HTTPS certificate (see note below).
To set the password via a standard HTTP connection, enter it directly in the first dialog shown below.
To set the password via an encrypted HTTPS connection, see “3.5.5 System >Security>HTTPS” of
User’s Manual.
Note: HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt the traffic between
web browsers and servers. The HTTPS certificate controls the encrypted exchange of information.
3.4 Live View Page
T
he live view pa
g
e comes in several screen
modes, for example 1920x1080,
1280x1024, 1280x720, 800x600, 704x480
(576), 640x480, 352x240 (288) and
320x240. Select the most suitable mode in
accordance with your PC specifications and
monitorin
g
purposes.
8

CE202D-N Series Quick Installation Guide
1) General controls
LiveViewPage Search&PlaybackPage SetupPage HelpPage
The video drop-down list allows you to select a customized or pre-programmed
video stream on the live view page. Stream profiles are configured under Setup > Basic
Configuration > Video & Image. For more information, see section “3.5.1 Basic Configuration >
Video & Image” of this user’s manual.
Theresolutiondrop-downlistallowstheselectionofthemostsuitablevideo
resolutions to be displayed on Live View page.
Theprotocoldrop-downlistallowstheselectionofthecombinationofprotocols
and methods to use depending on your viewing requirements and on the properties of the
network.
2) Control
toolbar
The live viewer toolbar is available in the web browser page only. It displays the following
buttons:
The Stop button stops the video stream being played. Pressing the key again toggles the
start and stop. The Start button connects to the network camera or start playing a
video stream.
The Pause button temporarily stops (pauses) the video stream being played.
The Snapshot button takes a picture (snapshot) of the current image. The location where
the image is saved can be specified.
The digital zoom activates a zoom-in or zoom-out function for video image on the live
screen.
The Full Screen button causes the video image to fill the entire screen area. No other
windows will be visible. Press the 'Esc' button on the computer keyboard to cancel full
screen view.
The Manual Trigger button activates a pop-up window to manually start or stop the event.
3) Video
Streams
The network camera provides several images and video stream formats. Your requirements and
the properties of your network will determine the type you use.
The Live View page in network camera provides access to H.264, MPEG-4 and Motion JPEG video
streams and to the list of available video streams. Other applications and clients can also access
these video streams/images directly, without going via the Live View page.
9

CE202D-N Series Quick Installation Guide
3.5 Resetting to the factory default settings
To reset the network camera to the original factory settings, go to the Setup>System> Maintenance
web page (described in “3.5.5 System > Maintenance”) or use the Reset button on the network
camera, as described below.
• Using the Reset Button
Follow the instructions below to reset the network camera to the factory default settings using
the Reset button.
1. Power off the network camera by disconnecting the power adapter.
2. Remove camera cover if not already done so.
3. Press and hold the Reset button with a straightened paperclip while reconnecting the power.
4. Keep the Reset button pressed during about 2 seconds.
5. Release the Reset button.
6. The network camera resets to factory defaults and restarts after completing the factory
reset.
7. Reattach the camera cover.
Caution: When performing a Factory Reset, you will lose any settings you have saved
3.7 More Information
For more information, refer to the network camera User’s Manual, which is available on the CD
included in this package.
10

C(202D-N Network Camera Dome
5030A
Vicon Industries Inc.
Internet Address: www.vicon-security.com