Vicon Surveyor MKII Series XX282-00-01 User manual

www.vicon-security.com
XX282-10-01
Surveyor® MKII Series
Pressurized Network
Camera Domes
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the
operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed
to be used in life-critical situations and must not be used for this purpose.
Vicon Industries Inc.
Tel: [phone] Fax: [phone] Toll Free: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300
Document Number: 8009-8282-10-01
Product specications subject to change without notice.
Issued: 117
Copyright © 2017 Vicon Industries Inc. All rights reserved.
Installation Guide

Introduction | 1-1
Surveyor MKII Pressurized Network Dome
Chapter
1
Introduction
1
This chapter provides general information about the Surveyor MKII
Pressurized Network Dome. Refer to the end of this chapter for the
organization of the rest of this manual.
The chapter consists of the following topics:
Topic Page
General Information 1-2
Model Tables 1-3
Organization of this Manual 1-4

1-2 | Chapter 1 Introduction
Surveyor MKII Pressurized Network Dome
General Information
The information in this manual covers the installation and operation of the
Surveyor MKII Network Pressurized Dome.
Note
Read all instructions before beginning any installation.
The Surveyor MKII series offer a rugged, pressurized and IP67 rated housing
for the Surveyor MKII Network camera dome.
The Surveyor MKII series provide network video transmission using high-
profile H.264 or M-JPEG compression. The dome supports ONVIF open
architecture connectivity to enable integration into third party Video
Management Systems (VMS), including Vicon’s Valerus and ViconNet.
The Surveyor MKII is designed for easy installation and serviceability. The
entire drive assembly simply snaps into the housing. When removed, the
mechanism retains all programmed functions in its on-board memory. The
customer interface board snaps down for easy access. A clear polycarbonate
lower dome is included. Additionally, two fiber versions, multi-mode and
single-mode, and a version for NTCIP are available.
The Surveyor MKII includes a high-definition 2.0 megapixel day/night camera
with wide dynamic range (WDR), digital noise reduction (FNR). See
Technical Information for camera features. Camera image settings are
configured via a user-friendly web browser interface.
For programming, refer to the most recent version of Surveyor MKII
Programming Manual. The Surveyor MKII series Pressurized Network Dome
is compatible with the SVFT-PR-WMA Wall Mount, and SVFT-PR-P Pipe
Adapter.
Surveyor MKII meets requirements for an FCC Class A computing device
and is UL and CE compliant. Surveyor MKII complies with the fire code of
certain local municipalities. The fire code for any given municipality should be
verified for Surveyor MKII’s compliance at the installation site.
The electronic components within the Pressurized Surveyor MKII are
sensitive to damage from ESD (Electro-Static Discharge). Appropriate
precautions and proper use of a ground strap should be observed at all times
when handling the unit or its subassemblies.
Table 1: Models and Descriptions
Model
Number
Environment
Resolution
Mount
Type
Optical Zoom/
Digital Zoom
Lower
Dome Type
SN230P
Outdoor/
Pressurized
2 megapixel
Pendant
30X
Clear

Introduction | 1-3
Surveyor MKII Pressurized Network Dome
Organization of this Manual
Chapter
Description
1
Introduction: Provides general information about the
Surveyor MKII
Pressurized Network Dome
2
Installation: Describes how to install the
Surveyor MKII
Pressurized
Network Dome and wiring instructions
3
Configuration and
Operation: Describes how to,
configure and operate the
Surveyor MKII Pressurized
Network Dome
4
Maintenance
and Reference: Describes basic system
maintenance, reference information, shipping instructions
and technical specifications for the
camera dome.

2-4 | Chapter 2 Installation
Surveyor MKII Pressurized Network Dome
Chapter
2
Installation
2
This chapter provides installation information for the Surveyor MKII
Pressurized Network Dome.
The chapter consists of the following topics:
Topic Page
Installation......................................................................................................2-6
Quick Installation.........................................................................................2-10
Detailed Installation.....................................................................................2-11
Uninstalling..................................................................................................2-32

Installation | 2-5
Surveyor MKII Pressurized Network Dome
Installation
Caution
This unit should only be installed by a qualified technician using common
hand tools and approved materials and wiring methods in accordance with
the National Electrical Code ANSI/NFPA 70, state and local wiring codes. All
interconnecting equipment or accessories must be UL Listed. Any mention in
this manual of alarm inputs/outputs have not been evaluated by UL to be
used for burglar alarm functionality.
How to Use this Manual
This manual was designed to provide the best overall instructions for the
installation and operation of the Surveyor MKII Pressurized Network Dome.
The graphics and terminology used in this manual have been carefully
selected to enable a clear and distinct understanding of the Surveyor MKII
series and its components. This manual has been formatted to present
distinct methods of installation for qualified service personnel only.
For a quick overview of product installation, see the Quick Installation sub-
section of the Installation section. Follow the references provided in the text
for items such as wiring tables and lower dome care. Refer to the subsequent
sections of Installation, Configuration and Operation for detailed descriptions
of any method.

2-6 | Chapter 2 Installation
Surveyor MKII Pressurized Network Dome
Accessory Kits
The accessory kit includes hardware necessary to assist in assembling the
Surveyor MKII; the screws and washers are spares for the lower dome:
Description
Quantity
23-pin connector
1
Screw, ¼-20x 5/8 hex head, stainless steel
4
Washer, lock 1.4 in., stainless steel
4
Screw, captive
2
Optionally, a 23-pin prefabricated cable assembly may be purchased
separately for ease of wiring.
Unpacking
All Vicon equipment is tested and inspected before leaving the factory. It is
the carrier’s responsibility to provide suitable delivery.
Inspect the cartons upon delivery and, if damage is present, make detailed
notes on the carrier’s bill. Then, obtain the carrier agent’s signature and file a
damage claim as soon as possible.
Open the cartons and inspect the equipment for damage. Save the cartons
and packing material. If damage is present, contact the carrier and file a
damage claim immediately. If the equipment must be returned for repair,
follow the instructions in the Shipping Information section of this manual.
Remove the Accessory Kit, the Customer Interface (CI) board and the unit
components from the box. Open the Accessory Kit and verify the hardware
contained in the kit against the preceding table.
Components
The Surveyor MKII Pressurized Housing is comprised of a housing, a camera
drive and a trim ring/lower dome assembly. These components may be
packed in separate boxes within the main box. This assembly is the heart of
the prepackaged pressurized housing version of the Surveyor MKII Camera
Dome. With the addition of a mount, the pressurized housing can be
equipped for indoor or outdoor wall mount or pipe mounting.

Installation | 2-7
Surveyor MKII Pressurized Network Dome
Note
By default, when the pressure in the housing dips below 1/2 psig an On
Screen Display message appears stating “Low Pressure Warning.”
Alternatively, this alarm warning may be sent to the CPU by enabling the
alarm in the camera dome’s menu. When this is activated, the On Screen
Display message will not appear. Additionally, the unit is preconfigured for
sensor titles to display for temperature, relative humidity and pressure. These
titles can be disabled in the Titling screen of the Web Browser. Refer to
Programming manual for titling and alarm information.
Housing
The housing is a combination cast aluminum frame and molded polyethylene
plastic UV-resistant weather-proof shell. It is used as the mounting frame for
the camera drive that mounts to the two (2) tabs on the inside of the housing.
The interior is environmentally controlled using a processor controlled
heater/fan assembly. A safety cord and clip are provided on the inside to
connect the camera drive latch during installation. The lower side of the
housing is equipped with a fill valve (Schraeder type); the top has a pressure
switch and a pressure relief valve. In addition, a 23-pin female, pressure-
rated connector is installed at the top for signal connection. An RJ-45
connector is provided for video/data transmission. There is also a rectangular
shaped flange surface with a four-hole bolt pattern, covered with gasket
material that is used to attach a pipe or wall mount. The inside of the housing
is factory-prepared for the installation of the camera drive mechanism. A
customer interface board, that can be unlatched or removed for easy access,
is installed in the top of the housing.
Camera Drive
The camera drive is comprised of an integral camera, pan-and-tilt drive and
CPU. It is designed for easy “snap-in” installation into the housing. The
camera drive quickly and accurately positions the camera in 360°of pan
angle and 92.5°of tilt angle. An additional thermostatically-controlled heater
is provided for temperature control.
Trim Ring/Lower Dome
The trim ring/lower dome is an assembly comprised of a 6.0-inch (152 mm)
diameter clear polycarbonate plastic shell and a cast aluminum/zinc color
coordinated trim ring. It contains a radial neoprene gland seal that
compresses and provides a pressure seal when the trim ring is attached to
the housing. The trim ring/lower dome assembly is attached using eight (8)
captive screws that require a torque wrench. It is also equipped with a safety
latch that is used to attach the housing’s safety cord. Refer to the
Maintenance Section of this manual for instructions on handling and care of
this lower dome.

2-8 | Chapter 2 Installation
Surveyor MKII Pressurized Network Dome
MAC Address
Each IP camera has a unique MAC address. This information is essential in
the camera configuration process. Before starting installation, make a record
of the IP address and location of the camera. The MAC address is located as
shown in the illustration below, under the connector on the mechanism.

Installation | 2-9
Surveyor MKII Pressurized Network Dome
Quick Installation

2-10 | Chapter 2 Installation
Surveyor MKII Pressurized Network Dome
Detailed Installation
Installation is a simple process. Choose the installation type based on the
mounting configuration. All mounting hardware (except for actual wall screws
and pipe) is provided. When unpacking, locate the provided accessory kit
containing a discrete 23-pin connector with crimp pins. If ordered, the
optional prefabricated 23-pin cable assembly can be used. Use the
applicable sub-section to install the correct connector type included.
Be sure to remove the black foam that keeps the camera in place in the
mechanism during shipping.
Wall Mount Method
Use this method to install, wire and configure a unit with a Vicon wall mount.
Refer to the Figure below as required.
Wall Mount Installation
Installing the Wall Mount
1. Select a suitable mounting location and verify there is sufficient cable
to reach the end of the wall mount.
Caution
Mount only to vertical structures with sufficient strength to support the mount
and unit and as vertically level as possible.
2. Mark and drill mounting holes in the surface using the wall mount
flange as a template. Drill through-holes for bolts or pilot holes for lag
screws.

Installation | 2-11
Surveyor MKII Pressurized Network Dome
Note
Verify there are no obstacles behind the surface before drilling.
3. Place a bead of silicone sealant around the wall mount mounting flange,
press it to the surface and line up the flange holes with drilled holes.
Install the appropriate 3/8 in. (9.5 mm) stainless steel hardware and
fasten snugly.
4. Place a bead of sealant around the flange to wall seam.
5. If routing the cables on the outside of the mount and through its access
hole, use the following steps:
a. Remove the plastic plug from the mount’s access hole.
b. Remove the mounting nut from the provided liquid tight fitting.
c. Insert the liquid tight fitting into the access hole, install and
tighten the nut securely.
d. The cables will be routed through a section of standard
0.75 in. (19 mm) conduit pipe later in this procedure.
e. Route the conduit pipe from the outside of the mount into, and
just through, the liquid tight fitting. Tighten the seal nut to
compress the gland around the conduit pipe. Place a bead of
sealant around the conduit pipe to gland seam.
Note
Routing an excessive length of conduit pipe through the liquid tight fitting can
cause difficulty in routing the cables through the mount.

2-12 | Chapter 2 Installation
Surveyor MKII Pressurized Network Dome
Pipe Mount Method
Use this method to install, wire and configure a pipe mounted unit. Refer to
Figure below as required.
Installing the Pipe Mount
1. Select a suitable mounting location and verify that the site wiring is
present.
Caution
Mount only to installed pipes with sufficient strength to support the mount and
unit and as vertically level as possible
2. Install a vertically hung 1-1/2 in. (38 mm) diameter NPT schedule 40 pipe
with a coupling on the end.
3. Using the provided sealant stick, apply generously around the threads.
4. Place the pipe mount on the thread and turn it clockwise, by hand, until it
fits snugly. Orient the service cover to a convenient position.
5. Tighten the two set screws on the neck of the mount using a hex key if
additional security is desired.

Installation | 2-13
Surveyor MKII Pressurized Network Dome
Installing the 23-Pin Connector Assembly
(If the prefabricated 23-pin cable assembly is used.)
6. Use the 23-pin cable assembly purchased separately. It should
resemble the assembly of Figure below.
a. Identify the cables required for attaching to the 23-pin
connector assembly. There should be a minimum of three (3),
power (18 to 32 VAC); pins L, M, J, K, and X are not used.
There could be optional site cables for alarm inputs or the
relay output (jacketed twisted pair).
b. Verify that each cable has had the jacket stripped back. If not,
strip back the jacket and individual wire covering to the
dimensions shown in the Figure that follows.
c. Identify each wire on the site installed cables and label them
(A, B, C, D, etc.) in accordance with the labels on the 23-pin
cable assembly wires.
d. Installing the cable assembly is complete. Proceed to Step 8.

2-14 | Chapter 2 Installation
Surveyor MKII Pressurized Network Dome
Note
The wire color code may not match the Figure. Verify each wire is labeled
with a function. DO NOT remove the labels. Use the wire labels for absolute
reference.
Wiring and Assembling the 23-Pin Connector
(Using the discrete 23-pin connector with crimp pins provided.)
7. Assemble the 23-pin connector as shown in Figure below.
a. Identify the cables required for attaching to the 23-pin
connector. There should be a minimum of three (3), power
(18 to 32 VAC); pins L, M, J, K, and X are not used. There
could be optional cables for alarm inputs or the relay output
(jacketed twisted pair).
b. Route all cables through the provided 2 in. (51 mm) length of
shrink wrap tubing and push the tubing a few feet down the
cable bundle.
c. Route all cables through the provided connector strain relief
fitting and push the connector near the shrink wrap tubing.

Installation | 2-15
Surveyor MKII Pressurized Network Dome
d. Prepare each cable by stripping back the jacket and individual
wire covering to the dimensions shown in preceding Figure.
e. Identify each wire on the site installed cables and label them
(A, B, C, D….etc.) in accordance with the labels on the 23-pin
connector assembly wires.
f. Attach a crimp connector to each wire and fasten with crimp
tool number M22520/1-01 and turret number M22520/1-02
manufactured by Astro Tool Company or equivalent.
Note
Use the provided large crimp connector for the Ground connection in the
Control (RS-422/485) cable.
Note
The wire color code may not match the Figure. Verify each wire is labeled
with a function. DO NOT remove the labels. Use the wire labels for absolute
reference.
g. Insert each labeled crimp connector into its respective labeled
23-pin connector position (A, B, C, D, etc.). Verify that each is
firmly seated.
h. Pull the strain relief fitting back up the cable and screw it
firmly into the base of the 23-pin connector assembly.
i. Gather all the cables at the other end of the strain relief fitting
into a bundle and tighten the two (2) strain relief fitting screws
until the cables are snugly captured.
j. Pull the shrink wrap tubing back up the cable and push it over
the strain relief fitting until it meets the base of the 23-pin
connector.
k. Using a heat gun or other directional heat source, heat the
shrink wrap tubing until it shrinks over the 23-pin connector
assembly and cables.
l. Identify each wire on the site installed cables and label it
(A, B, C, D, etc.) in accordance with the labels on the 23-pin
connector assembly wires. Assembling the connector is
complete.
Caution
Overheating the shrink wrap tubing can result in damage to the tubing and
the entire 23-pin connector assembly.
8. Remove the service cover from the front of the wall mount by removing
the four (4) captive screws.

2-16 | Chapter 2 Installation
Surveyor MKII Pressurized Network Dome
9. Route the 23-pin connector assembly through the service cover and out
the back of the wall mount. Leave the 23-pin connector assembly and an
excess of about 2 in. (51 mm) of cable at the service opening.
10. Inspect the top of the housing assembly and verify that there is no debris
on the gasket area. If there is, wipe this surface clean with a cloth.
11. Lift the top of the housing assembly up to the wall mount’s pressurized
housing mounting flange. Align the two (2) sets of four (4) mounting holes
so that the relief valve is located closest to the service opening (slightly
off to the right side, facing forward). Press firmly.
Note
Failure to correctly orient the Housing can cause difficulty in future servicing.
12. Insert the four (4) provided ¼-20 x 5/8 in. (16 mm) long hex head screws
through the provided ¼ in. (6 mm) lockwashers and into the mounting
holes. Tighten all screws securely with a 5/8 in. (16 mm) socket wrench.
Carefully release the housing assembly and verify that the mount can
support the weight load.
13. With the housing assembly attached to the wall mount, locate the 23-pin
connector assembly in the service opening.
14. Insert the 23-pin connector assembly into the mating 23-pin connector on
the top of the housing assembly. Turn it until it drops down into the keyed
slot and twist it clockwise ¼ turn to lock it.
15. Connect the previously labeled site wiring to their corresponding cable
assembly labeled wires using standard wiring practices such as wire
nuts. If using conduit, route all cables through the liquid-tight
fitting/conduit, previously installed in the access hole, before connecting
to the site wiring.
16. At the lower side, remove the cap from the fill valve. Using a small-tipped
instrument, press the internal pin down to release any residual gas from
the housing.
17. Loosen the eight (8) captive screws from the trim ring/lower dome
assembly and lower it. Allow the lower dome to hang from its safety cord
during the remaining assembly.
Housing Connections
All the necessary connections are provided at the top of the housing,
including the 23-pin connector and connectors for IP video/data transmission.
Refer to the figure below.

Installation | 2-17
Surveyor MKII Pressurized Network Dome
Preparing the Camera Drive
Open the box containing the camera drive assembly and CI board and
remove them.
Install the Customer Interface (CI) board, which is packed separately under
the mechanism, into the housing. Make connections to the CI board using
23-pin configured cable. Ensure that the clear tubing is connected securely to
the pressure sensor on the CI board.
18. Attach the housing’s safety clip to the camera drive’s tab. Tilt the camera
drive down and orient the two (2) slots on the housing with the two (2)
tabs on the drive and raise it until two distinct clicks are heard. The
housing is now securely installed.
19. Verify that the O-ring in the groove of the trim ring assembly is properly
seated, free of debris and has a light coat of vacuum grease. If not, seat
the O-ring in the groove, remove any debris and rub additional vacuum
grease on it.
Connect plastic tube to
pressure sensor.

2-18 | Chapter 2 Installation
Surveyor MKII Pressurized Network Dome
20. Attach the trim ring lanyard to the trim ring assembly and mate it to the
housing by aligning the housing holes with the trim ring/lower dome
holes. Install the eight (8) screws and tighten only with a torque wrench
set for 15-in. lb (170-N cm) of force. Use an alternating (star) pattern to
tighten all the screws.
Pressurizing the Housing Assembly
Refer to Figure below as needed.
21. Reattach the previously removed service cover to the service opening
using the four (4) captive screws.
22. Using a regulated source of dry Nitrogen gas with the proper Schraeder
type fill fitting, as shown in Figure 5, regulate the gas pressure to 10.0 psi
(0.68 atm or bars).
23. Attach the fill fitting to the housing assembly’s fill valve located at the
lower side of the housing and pressurize the housing assembly. When
the relief valve opens (gas will hiss from the top of the relief valve), allow
this to purge for a minimum of 5 minutes to assure that all the enclosed
air is replaced by nitrogen; then remove the fill fitting. The relief valve is
rated at 5 psi (0.34 atm or bars). Monitor the actual pressure for the next
hour. If, in one hour the pressure has not dropped below 4.5 psi
(0.31 atm or bars), it is assumed that the housing assembly is sealed and
the relief valve is seating properly.
24. Reinstall the cap on the fill valve.
Caution
Pressurizing the housing assembly beyond 10 psi, or with an unregulated
gas source, can cause severe injury to personnel and permanent damage to
the assembly.
Warning
If the dome has been dropped and is cracked, do not pressurize. Replace it
with a new dome
Notes
•The housing with mechanism has approximately 490 in.3of volume.
•Leakage rate is less than 2 psi per year.
•The pressurized function has not been evaluated by UL.

Installation | 2-19
Surveyor MKII Pressurized Network Dome
Warning
Do not use any gas type other than dry Nitrogen. The use of Shop Air can
introduce moisture into the housing assembly that can damage it over time.
Proceed to the Operation section of this manual.
Communication Ports
If using NTCIP protocol, communicate to the Surveyor MKII using ports
3000/UDP or 3001/TCP.
If using ONVIF, use port 8000. This is set in the web browser.