Vicon V992B-IR4 User manual

www.vicon-security.com
XX248-50-01
V992B-IR4 Network
Bullet Camera
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the
operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed
to be used in life-critical situations and must not be used for this purpose.
Vicon Industries Inc., 89 Arkay Drive, Hauppauge, New York 11788
Tel: [phone] Fax: [phone] Toll Free: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300
Document Number: 8009-8248-50-01
Product specications subject to change without notice.
Issued: 512
Copyright © 2012 Vicon Industries Inc. All rights reserved.
Installation Guide

Contents
1. PRODUCT FEATURES.........................................................................................................................1
2. INSTALLATION.....................................................................................................................................2
2.1INSTALLATION PREPARATION...............................................................................................................2
2.2ASSIGN IP ADDRESS..........................................................................................................................4
2.3 ACCESS FROM A BROWSER......................................................................................................................5
2.4ACCESSING THE V992B FROM THE INTERNET..........................................................................................6
2.5ADJUSTING THE IMAGE AND FOCUS..........................................................................................................6
3. LIVE VIEW............................................................................................................................................7
3.1 VIDEO STREAM TYPES...........................................................................................................................7
3.2 HOW TO STREAM H.264........................................................................................................................8
4. SETUP...................................................................................................................................................9
4.1 INSTALL.....................................................................................................................................................9
4.1.1 Installation Setup............................................................................................................................9
4.2 VIDEO.....................................................................................................................................................10
4.2.1 Codec............................................................................................................................... ..............10
4.2.2 V992B............................................................................................................................... ..............12
4.3 LIVE........................................................................................................................................................14
4.3.1 Viewer Setup...............................................................................................................................14
4.3.2 Privacy Mask...............................................................................................................................14
4.4.FTP........................................................................................................................................................16
4.4.1 Config............................................................................................................................................16
4.4.2 Event.............................................................................................................................................16
4.4.3 Periodical......................................................................................................................................17
4.5.EVENT....................................................................................................................................................18
4.5.1 Motion............................................................................................................................................18
4.5.2 Mapping........................................................................................................................................19
4.6 NETWORK..............................................................................................................................................19
4.6.1 IP Setup........................................................................................................................................19
4.6.2 Service Port.................................................................................................................................21
4.6.3 E-mail............................................................................................................................................22
4.7 SYSTEM..................................................................................................................................................22
4.7.1 User...............................................................................................................................................23
4.7.2 Date / Time..................................................................................................................................23
4.7.3 Maintenance.................................................................................................................................24
4.7.4 Information....................................................................................................................................26
6.DIMENSIONS...................................................................................................................................27
SHIPPING INSTRUCTIONS...................................................................................................................30
VICON STANDARD EQUIPMENT WARRANTY...................................................................................31
VICON PART NUMBER:8006-9010-03-10 REV 0412...............................................................................31

1
1. Product Features
The V992B is a high performance H.264 network bullet V992B, designed for demanding
security installations. It delivers crisp, clear images, disclosing every detail, thanks to its top
quality 3.0 Megapixel progressive CMOS sensor and advanced image processing.
Supported by the industry’s largest base of video management software, the V992B
provides the perfect solution for securing bank offices, airports and other facilities, and for
traffic surveillance, over IP based networks.
The optimal Power over Ethernet (IEEE 802.3af) support power to the V992B to be delivered
via the network, eliminating the need for a power outlet and reducing installation costs.
Steady power could be guaranteed with a central Uninterruptible Power Supply (UPS).
The V992B offers a comprehensive set of network security and management features. This
includes support for port based network control (IEEE802.1X), which allows the V992B to be
connected to a network secured with this control, and HTTPS encryption, which provides a
secure channel between V992B and application. It also enables authentication of the video
source. Video products are efficiently managed with the powerful V992B Management tool,
which is provided on the Installation CD which comes with each V992B.
1. Network connector
The V992B connects to the network via a standard network cable, and automatically detects
the speed of the local network segment (10BaseT/100BaseTX Ethernet). This socket could
also be used to power the V992B via Power over Ethernet (PoE). The V992B auto-senses
the correct power level when using a PoE (Class 2) switch, router or injector.
2. Reset Button
Press this button to restore the V992B configuration to its factory default settings.

2
2. Installation
2.1 Installation Preparation
Assembly the sun visor and V992B.
Connect the V992B to the network using a shielded network cable.
Adjust position of camera on target.
PORTS AND BUTTONS
DESCRIPTION
1. Control button
2. Network port
3. BNC (Analog video out)
Mounting to a ceiling / wall
1) IN CEILING MOUNT

3
SURFACE MOUNT

4
2.2 Assign IP address
The default setting of the V992B is set “DHCP” to ON. If you have a DHCP server on your
network and UPnP function enabled on your PC you can find the network V992B in “My
network”.
If a DHCP server is not available on your network, assign IP address by the following process:
Execute Multi-Upgrade Tool (from the Installation CD). It will search V992Bs on the network
automatically.
1) After the list of detected devices appears, select the V992B you are trying to configure.
2) Select the Network type as Static or DHCP. If Static is selected, enter all of the network
information for your V992B.
3) Select the “Change IP Address” button. The message “Do you want to change IP
address?” will display; select “Yes” from the pop-up window.
4) Check the Type as Static or DHCP from the list.
When you double click the V992B within the list, the default web browser (Internet
Explorer or compatible equivalent) will open and automatically connect to the V992B.
The V992D-N4 can be accessed with most standard operating systems and browsers. The
recommended browser is Internet Explorer® 7 and above for Windows®.

5
2.3 Access from a browser
1. Start a browser (i.e., Internet Explorer)
2. Enter the IP address or host name of the V992B in the Location/Address field of your
browser. Press Enter.
3. Login dialog will appear when the V992B is accessed for the first time.
4. The default user name is ADMIN, and password is 1234.
5. The V992B’s Live View page is now displayed in your browser.
When you first access the V992B you will be asked to download and install an Active X
control from the V992B to display a Live image.

6
NOTE: The layout of the live view page in the V992B may have been customized to meet
specific requirements. Consequently, some of the examples and functions featured
here may differ from those displayed on your own Live View page.
2.4 Accessing the V992B from the Internet
Once installed, the V992B is accessible on the local network (LAN). Configure the
router/firewall to allow incoming data traffic to access the V992B from the Internet. For
security reasons this is usually done on a specific port. Please refer to the documentation
for router/firewall for further instructions.
2.5 Adjusting the Image and Focus
To adjust the position of the lens:
1. Open the Live View page in your web browser.
- Select the Setup tab, and open the Installation page.
- Select the ‘Video Format'.
2. Connect analog monitor to the VIDEO OUT (BNC) on the cable.
- Adjust lens position and set FOCUS with supplied focus adjust ring.

7
3. Live View
Digital Zoom
Snap Shot
Full Screen
Video Stream change: First stream Second stream
Play: Click this button by manually to start the stream
Stop: Click this button by manually to stop streaming
NOTE: It is possible that not all the buttons described below will be visible unless the Live
View page has been customized to display them.
3.1 Video Stream Types
Motion JPEG
This format uses standard JPEG images in the video stream. These images are then
displayed and updated at a rate sufficient to create a stream that shows constantly updated
motion.
The Motion JPEG stream uses a considerable amount of bandwidth, but it also provides
excellent image quality and access to every individual image contained in the stream.
H.264 protocols and communication methods
• RTP (Real-time Transport Protocol) is a protocol that allows programs to manage the real-
time transmission of multimedia data, via unicast or multicast.
• RTSP (Real Time Streaming Protocol) serves as a control protocol, to negotiate the type of
transport protocol to use for the stream. RTSP is used by a viewing client to start a unicast
session.
• UDP (User Datagram Protocol) is a communications protocol that offers limited service for
exchanging data in a network which uses the Internet Protocol (IP).
UDP is an alternative to the Transmission Control Protocol (TCP). The advantage of UDP is
that, it is not required to deliver all data and may drop network packets when there is
network congestion. This is suitable for live video, as there is no point in re-transmitting old
information that will not be displayed anyway.
• Unicasting is communication between a single sender and a single receiver over a
network. This means that the video stream goes independently to each user, and each user
gets own stream. A benefit of unicasting is, in case one stream fails, it only affects one user.

8
• Multicasting is bandwidth-conserving technology that reduces bandwidth usage by
simultaneously delivering a single stream of information to multiple network recipients. This
technology is used primarily on delimited networks (intranets), as each user needs an
uninterrupted data flow and should not rely on network routers. (Note that multicasting may
not be available with the firmware you received; check the Vicon website for updated
firmware.)
3.2 How to Stream H.264
Deciding on the combination of protocols and methods to use depends on your viewing
requirements, and on the properties of your network. Setting the preferred method(s) is done
in webpage.
RTP+RTSP
This method (actually RTP over UDP and RTSP over TCP) should be your first
consideration for live video, especially when it is important to always have an up-to-date
video stream, even if some images are lost due to network problems. This could be
configured as multicast or unicast.
RTP/RTSP/Unicasting should be used for video-on-demand broadcasting, so that there is
no video traffic on the network until a client connects and requests the stream. However, as
more and more unicast clients get connected, the traffic on the network will increase and
may cause congestion. Although there is a maximum of 10 unicast viewers, note that all
multicast users combined count as 1 unicast viewer.
RTP/RTSP
This unicast method is RTP tunneled over RTSP. This could be used to exploit the fact that it
is relatively simple to configure firewalls to allow RTSP traffic.

9
4. Setup
The V992D-N4 is configured from the Setup link, which is available on the top left hand side
in the web interface. This configuration could be done by:
• Administrators, who have unrestricted access to all settings under the Setup tab.
Accessing the Setup link from a browser
1. Start your web browser and enter the IP address or host name of the V992B into the
address bar.
2. The Live View page is now displayed. Click on the Setup tap.
4.1 Install
4.1.1 Installation Setup
Installation Mode allows use of the analog BNC output from the V992B to connect the
V992B
NTSC, PAL: Analog Output is enabled.
OFF: Analog output will be disabled.

10
4.2 Video
The following descriptions show examples of some of the features available with V992D-N4.
4.2.1 Codec
This section allows you to choose the compression codec for each of the video streams.
Codec
H.264
This is a video compression standard that makes good use of bandwidth and could
provide high-quality video streams.
The H.264 standard provides the scope for a large range of different coding tools for use
by various applications in different situations, and the V992D-N4 provides certain
subsets of these tools.
Using H.264, it is also possible to control the bit rate, which in turn allows the amount of
bandwidth usage to be controlled. CBR (Constant Bit Rate) is used to achieve a specific
bit rate by varying the quality of the H.264 stream. While using VBR (Variable Bit Rate),
the quality of the video stream is kept as constant as possible, at the cost of a varying bit
rate.
Motion JPEG
This format uses standard JPEG still images in the video stream. These images then are
displayed and updated at a rate sufficient to create a stream that shows constantly
updated motion.
The Motion JPEG stream uses considerable amounts of bandwidth, but also provides
excellent image quality and access to every individual image contained in the stream.
Multiple clients accessing Motion JPEG streams could use different image settings.

11
Size
Video output resolution. See the output resolution table that follows.
Frame rate
1 ~ 30fps (60Hz) / 1 ~25fps (50Hz)
GOP Size
1 ~ 60 frames
Bit-rate control (CBR or VBR)
When using H.264 compression, if there is only limited bandwidth available, a constant bit
rate (CBR) is recommended, although this may compromise image quality. Use a variable
bit rate (VBR) for the best possibly image quality.
Average Bit-rate (512Kbps ~ 10Mbps)
Recommended bit rate for D1 or VGA : 800Kbps ~ 1Mbps
Recommended bit rate for 1.3M (720p) : 3Mbps ~ 4Mbps
Recommended bit rate for 2.0M (1080p) : 6Mbps ~ 8Mbps
Boost Quality
The Boost feature is used in conjunction with Video Motion Detection (VMD). When this
feature is turned ON, the Boost FPS can be set to a different value than the Frame Rate set
for the V992B in the field above. When motion is detected, the V992B will boost the fps from
the regular level set for the V992B to this boosted level for the duration of the motion. Boost
Quality can be set ON or OFF. (Note that multicasting may not be available with the firmware
you received; check the Vicon website for updated firmware.)
Quality
1 ~ 100 This parameter is only available in M-JPEG mode.
Anti-Flicker mode (Flicker less mode)
60Hz / 50Hz
Video Mirroring
Select Video Mirroring mode NONE/HORIZONTAL/VERTICAL/FLIP(H+V)

12
< Output resolution and Frame rate table for V992B > (Unit: fps)
First
Stream Second Stream
1920x1080 704x480 640x480 640x360 640x352 352x288 352x240 320x240 -
1280x1024 704x480 640x480 640x360 352x288 352x240 320x240 - -
1024x768 704x480 640x480 640x360 352x288 352x240 320x240 - -
1280x720 1280x720 704x576 704x480 640x480 640x360 352x288 352x240 320x240
704x576 704x576 640x480 640x360 352x288 - - - -
704x480 704x480 640x480 640x360 352x240 - - - -
640x480 640x480 320x240 - - - - - -
640x360 640x360 320x240 - - - - - -
352x288 352x288 - - - - - - -
352x240 352x240 - - - - - - -
320x240 320x240 - - - - - - -
4.2.2 V992B
This section allows you to adjust various V992B settings.
This section allows you to adjust various V992B settings.
Exposure Control
Exposure Mode

13
AUTO: Use this setting for automatic exposure control.
MANUAL: Use this setting to control V992B exposure manually.
To compensate for poor lighting conditions, you can adjust the Color level, Brightness,
Sharpness, Contrast and Exposure control.
NOTE: When AE is enabled, some of the submenus (AGC Gain, e-Shutter Speed) will be
disabled.
AGC Gain
0 ~ 36 dB
Slow shutter mode
For low light conditions, turn on slow shutter mode.
Max AGC Gain
LOW/HIGH selectable.
BLC Control (Back Light Compensation)
The BLC adjusts the exposure of scenes with strong backlight in the center-bottom of the
image. When the image background is too bright, or the subject too dark, backlight
compensation makes the subject appear clearer. The settings for low light behavior
determine how the V992B behaves sat low light levels. These settings affect video image
quality and how much noise is in the images.
Day & Night Control
Day & Night Mode
Auto/Day/Night
Set this filter to OFF to allow the V992B to 'see' infrared light, removing the IR cut filter,
when using an IR illuminator. This will make the image clearer. If set to Auto, the V992B will
automatically switch between IR cut filter On and Off, according to the current lighting
conditions.
0/5/10/15/30/60 sec: Set detection window time in order to avoid failure switching.
White Balance Control
WB Mode
AUTO: Automatic White balance
MANUAL: Manual White balance
The White balance adjustment setting is used to make the colors in the image appear
consistent, compensating for the different colors present in different light sources.
The V992D-N4 V992B can be set to automatically identify the light source and compensate
for its color temperature. If necessary, the type of light source could be set manually.
Image Property Control
Modify the video signal parameters, such as: Brightness, Sharpness, Contrast, and Color.
Sharpness (Default: 8, Range: 1~15)
Brightness (Default: 15, Range: 0~30)
Contrast (Default: 15, Range: 0~30)
Color (Default: 15, Range: 0~30)

14
4.3 Live
V992D-N4 can support up to 10 simultaneous users via unicast.
4.3.1 Viewer Setup
Live View Protocol
RTP Unicast (UDP) / RTP over RTSP (TCP)
Buffering Time (frame based)
Determines (0 ~ 90) x 1/30 sec (0 ~ 3sec)
Viewer OSD Setup
Date: Determines whether the date is displayed.
Resolution: Determines whether the V992B resolution is displayed.
Event State: Determines whether the event state is shown on display window (M for
motion is shown in Live View).
4.3.2 Privacy Mask
The IP Camera can support the Privacy Mask feature so a portion of the frame can
be blocked based on personal preference or legal requirements.
Log into WebRA web viewer and click on the Setup tab. Then choose Live from the
menu on the left and select Privacy Mask.

15
Select the Area and Color for the mask and use the mouse to drag the cursor
to fill the area to be set as a Privacy Mask.
Click Save and then click the Live tab on the top to confirm the Privacy Mask
satisfies preferences and/or requirements.

16
4.4.FTP
4.4.1 Config
Server Configuration
Allows transmission of still images to remote sites using the FTP server. Set the
information for FTP transmission by inserting the IP address, Port, Username and
Password of the remote FTP Server.
4.4.2 Event
Event FTP Sending
You can configure the V992B to upload still images to FTP server based on event such as
Motion detection.

17
Directory
The name of the directory where the still images will be stored when an Event occurs.
File Prefix
You may add a file name prefix to the stored image file name.
Example: If the file prefix is ‘MVD’, the still image would be saved as MVD_date_time.jpg.
FTP Send Mapping
Choose which types of events will be recorded to the FTP server by checking the desired
event.
Effective Period
This parameter lets you decide whether to save all the events that are happening at all
hours of the day, or only the events that occur within during specific times of the day. The
Schedule method is used to save events into the FTP server during a specific time range.
The start time and the end time can be set using the dropdown list.
4.4.3 Periodical
Periodical FTP Sending
It allows transmission of still images periodically to the FTP server.
Directory
The name of the directory where the still images will be stored.
File Prefix
You may add a file name prefix to the stored image file name.
Example: If the file prefix is ‘per’, the still image would be saved as per_date_time.jpg.

18
Interval
It allows for saving still images based on frequency (1 image every 10 sec, for example).
Use the drop-down control to set from 10 seconds to 1 hour.
Effective Period
This parameter lets you decide whether to save still images at all hours of the day, or
during specific times of the day.
4.5.Event
4.5.1 Motion
Motion Detection
Motion detection is used to generate an alarm whenever movement occurs within the
video image.
A total of 4 motion detection zones can be configured.
Configuring Motion Detection
1. Click Motion in the Event menu.
2. Click Area1-4 button for the area to be defined and select the corresponding area for
motion detection by clicking the relevant color box.
3. Click the box on the video image where the motion area is to be located and adjust the
size of the area by dragging the outlined box across and down in one motion.
4. Adjust the Object Sensitivity from the drop down list, 1-10. The Sensitivity list only
displays when an area is selected; it is not visible when All View is selected. Use the
Selectall button to have the entire scene in the selected area. Deleteall is available to
eliminate all selected areas.
5. Click Save. When motion occurs in the defined area, a red dot appears on the Live video.