Vicon V9360-1 Quick start guide

www.vicon-security.com
XX271-00-00
V9360-1 Series
Network Hemispheric Camera
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the
operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed
to be used in life-critical situations and must not be used for this purpose.
Vicon Industries Inc.
Tel: [phone] Fax: [phone] Toll Free: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300
Document Number: 8009-8271-00-00
Product specications subject to change without notice.
Issued: 215
Copyright © 2015 Vicon Industries Inc. All rights reserved.
Software Guide

1
Table of Contents
1. Overview................................................................................................................................4
2. Menu Tree..............................................................................................................................4
2.1 Home Page..................................................................................................................5
2.1.1 Function Items on Home Page.....................................................................5
2.1.2 Function Differences between Models........................................................10
2.2 System ......................................................................................................................11
2.2.1 System.......................................................................................................11
2.2.2 Security......................................................................................................13
2.2.2.1 User............................................................................................13
2.2.2.2 HTTPS........................................................................................15
2.2.2.3 IP Filter.......................................................................................17
2.2.2.4 IEEE 802.1X...............................................................................19
2.2.3 Network......................................................................................................20
2.2.3.1 Basic...........................................................................................20
2.2.3.2 QoS ............................................................................................24
2.2.3.3 SNMP.........................................................................................25
2.2.3.4 UPnP..........................................................................................27
2.2.4 DDNS.........................................................................................................28
2.2.5 Mail ............................................................................................................29
2.2.6 FTP............................................................................................................29
2.2.7 HTTP..........................................................................................................30
2.2.8 Events........................................................................................................30
2.2.8.1 Application (Compact Fixed Dome Excluded).............................30
2.2.8.2 Motion Detection.........................................................................35
2.2.8.3 Network Failure Detection...........................................................41
2.2.8.4 Tampering...................................................................................43
2.2.8.5 Periodical Event..........................................................................47
2.2.8.6 Manual Trigger............................................................................50
2.2.9 Storage Management (Local Recording)....................................................54
2.2.9.1 SD Card......................................................................................54
2.2.9.2 Network Share (NAS) .................................................................56
2.2.10 Recording (Local Recording)......................................................................58
2.2.11 Schedule....................................................................................................59
2.2.12 File Location (Snapshots and Web Recording)...........................................60
2.2.13 Iris Adjustment (CS Mount Lens Only)........................................................60
2.2.14 View Information ........................................................................................60
2.2.14.1 Log File.......................................................................................60
2.2.14.2 User Information .........................................................................61

2
2.2.14.3 Parameters.................................................................................61
2.2.15 Factory Default...........................................................................................62
2.2.16 Software Version........................................................................................62
2.2.17 Software Upgrade ......................................................................................63
2.2.18 Maintenance...............................................................................................64
2.3 Streaming..................................................................................................................65
2.3.1 Video Format (Video Resolution and Rotate Type).....................................65
2.3.2 Video Compression....................................................................................67
2.3.3 Video ROI ..................................................................................................68
2.3.4 Video OCX Protocol...................................................................................69
2.3.5 Video Frame Rate......................................................................................70
2.3.6 Video Mask ................................................................................................70
2.3.7 Audio (Audio Mode and Bit Rate Settings) .................................................71
2.4 Camera......................................................................................................................73
2.4.1 Exposure....................................................................................................73
2.4.2 White Balance............................................................................................75
2.4.3 Picture Adjustment.....................................................................................78
2.4.4 Backlight ....................................................................................................79
2.4.5 Digital Zoom...............................................................................................79
2.4.6 IR Function.................................................................................................79
2.4.7 WDR Function............................................................................................80
2.4.8 Noise Reduction.........................................................................................81
2.4.9 Fisheye Correction (Fisheye IP Camera Only) ...........................................82
2.4.10 TV System..................................................................................................86
2.5 Pan Tilt......................................................................................................................87
2.5.1 Preset.........................................................................................................87
2.5.2 Sequence...................................................................................................88
2.5.3 Pan/Tilt Control ..........................................................................................89
2.6 Logout .......................................................................................................................91
Appendix A: Install UPnP Components.....................................................................................92
Appendix B: IP Addresses from Decimal to Binary..................................................................93
Appendix C: Video Resolution...................................................................................................94
Quad Streams ...........................................................................................................94
Triple Streams.........................................................................................................106
Dual Streams...........................................................................................................110
Single Stream..........................................................................................................111
Single Stream- 2M Only...........................................................................................111
Quad Streams- 3M/4M Real-Time...........................................................................112
Triple Streams- 3M/4M Real-Time...........................................................................122
Dual Streams- 3M/4M Real-Time.............................................................................126

3
Single Stream- 3M/4M Real-Time............................................................................127
5M Fisheye IP Camera .......................................................................................................128
Dual Streams- Front End Correction........................................................................128
Single Stream- Front End Correction.......................................................................128
Quad Streams- Back End Correction.......................................................................129
Triple Streams- Back End Correction.......................................................................141
Dual Streams- Back End Correction........................................................................147
Single Stream- Back End Correction .......................................................................148
6M Fisheye IP Camera .......................................................................................................149
Dual Streams- Front End Correction........................................................................149
Single Stream- Front End Correction.......................................................................149
Quad Streams- Back End Correction.......................................................................150
Triple Streams- Back End Correction.......................................................................158
Dual Streams- Back End Correction........................................................................163
Single Stream- Back End Correction .......................................................................164

4
1. Overview
The V9360-1 Ultra High Definition Multiple Streams IP Camera is provided with
a user-friendly browser-based configuration interface, and a free bundled CMS
(Central Management System) for video playback and recording. In this manual,
information about main page introduction, system related settings and camera
settings will be described in detail. For further information about CMS, refer to
CMS User’s Manual.
2. Menu Tree
There are six main tabs including <Home>, <System>, <Streaming>, <Camera>,
<Pan Tilt> and <Logout> on the Home Page.
Home
Users can monitor live video of the targeted area.
System setting
The administrator can set host name, system time, root password, network
related settings, etc. Further details will be interpreted in chapter System.
Streaming setting
The administrator can modify video resolution and rotate type and select audio
compression mode in this page.
Camera setting
This setting page is only available for the administrator and user accounts that
have been granted the privilege of camera control. In this setting page, the
administrator and users can adjust various camera parameters, including
<Exposure>, <White Balance>, <Picture Adjustment>, <Backlight>, <Digital
Zoom>, <IR Function>, <WDR Function>, <Noise Reduction> and <TV
System>.
Pan Tilt setting
This setting page is only available for the administrator and user accounts that
have been granted the privilege of camera control. The administrator and users
can set preset point and sequence line in this page. However, only the
administrator can access the <Pan/Tilt Control> setting to activate the pan/tilt
function and select the RS-485 protocol.

5
NOTE: Pan/Tilt function is only available for Zoom AF Box Camera and
Box Camera (DC12V / AC24V / PoE Model).
Logout
Click on the tab to re-login to the camera with another username and password.
2.1 Home Page
Click on the tab <Home> to access the home page. There are several function
buttons on the home page. Detailed information of each item is described in the
following section.
NOTE: The function items vary from models to models; refer to section
Function Differences between Models for more detail.
2.1.1 Function Items on Home Page
Multiple Languages Support
Multiple languages are supported, including German, English, Spanish, French,
Italian, Japanese, Korean, Portuguese, Russian, Simplified Chinese and
Traditional Chinese for the viewer window interface.
Digital Zoom Control
In the full screen mode, users can implement digital PTZ by rotating the mouse
wheel (for zoom in/out) and dragging the mouse in any direction.
Screen Size Adjustment
Image display size can be adjusted to x1/2 and full screen.
Talk button
(On/Off)
Talk function allows the local site to talk to the remote site. Click on the button
to enable/disable the talk function. Refer to Security> User> Add user> Talk /
Listen for further details.
NOTE: This function is only open to “User” who has been granted this
privilege by the administrator.

6
Speaker button
(On/Off)
Click on the <Speaker> button to mute/activate the audio.
NOTE: This function is only available for “User” who has been
granted this privilege by the administrator.
Snapshot button
Click on the button and the JPEG snapshots will automatically be saved in the
appointed place. The default place for saving snapshots is: C:\. To change the
storage location, refer to section File Location for further details.
NOTE: With Windows 7 or Windows 8 operating system, to implement
the Snapshot function, users must run IE as administrator. To run IE as
administrator, right click on the IE browser icon and select “Run As
Administrator” to launch IE.
Video Streaming Pause/Restart button
(Pause/Restart)
Click on the <Stop> button to disable video streaming; the live video will be
displayed as black. Click on the <Restart> button to show the live video again.
Web Recording button
(On/Off)
Click on the <Recording> button and the Live View through the web browser
will be directly recorded to the specific location on the local hard drive, which
could be configured in the <File Location> page. The default storage location
for the web recording is: C:\. Refer to section File Location for further details.
NOTE: With Windows 7 or Windows 8 operating system, to implement
the Web Recording function, users must run IE as administrator. To run
IE as administrator, right click on the IE browser icon and select “Run
As Administrator” to launch IE.
Manual Trigger Button
(On/Off)
Click on the <Manual Trigger > button to turn on and off the manual trigger.
Refer to section Manual Trigger of the next chapter for further details.

7
Zoom Adjustment
Tele/Wide buttons
Hold the <Tele/Wide> button and implement continuous zoom
adjustment.
Tele/Wide Steps buttons
Select a Tele/Wide step value from the drop-down menu. Then click on
the <Tele/Wide Steps> button to shift the zoom lens according to the
defined value.
Reset button
Click on the <Reset> button and the zoom lens will be calibrated to the
maximum wide end.
Manual Focus Adjustment
Near/Far buttons
Hold the <Near/Far> button and implement continuous focus
adjustment.
Near/Far Steps buttons
Select a Near/Far step value from the drop-down menu. Then click on
the <Near/Far Steps> button to shift the focus lens according to the
defined value.
Reset button
Click on the <Reset> button and the focus lens will first be reset to the
maximum near end. Then the lens will be calibrated to a suitable
position according to the monitoring environment.
Push AF
The One Push AF function is for fixing the focus in one click.

8
Auto Focus (AF) Adjustment
The AF mode can be defined as continuous AF, zoom trigger AF and push AF.
Manual button
Click on the <Manual> button and users can adjust the focus manually
via the <Near/Far> buttons.
Cont. (Continuous AF)
In this mode, the camera will focus automatically and continuously,
regardless of zoom changes or any view changes.
Zm Trig (Zoom Trigger AF)
In this mode, AF is activated every time zoom is adjusted.
Push AF
The One Push AF function is for fixing the focus in one click.
Fisheye Image Adjustment
Fisheye Source Image
Click on the <Fisheye Source Image> button to view the live videos as
hemisphere fisheye source images.
Single ePTZ
Click on the <Single ePTZ> button to view the dewarped live images
and virtually pan/tilt /zoom the camera according to users’ needs.
Users can implement virtual PTZ by rotating the mouse wheel (for
zoom in/out) and dragging the mouse in any direction.
360°Panoramic
Click on the <360° Panoramic> button to view the dewarped live
images as two 180°views.
Quad View
Click on the <Quad View> button to view the dewarped live images as
four ePTZ views.
180°Panoramic
Click on the <180°Panoramic> button to view the dewarped live video
as a single 180°view.

9
Dual ePTZ
For cameras installed on a wall mount, click on the <Dual ePTZ>
button to view the dewarped live video as a single 180° view with two
ePTZ views. Users can implement virtual PTZ by rotating the mouse
wheel (for zoom in/out) and dragging the mouse in any direction in the
ePTZ live video panes.
The available Fisheye Image Adjustment buttons are different depending on the
dewarping method and installation method selected on the <Fisheye Correction>
setting page. The following table shows the available buttons for different
dewarping methods and installation methods. The supported buttons are
represented by “√”.
Dewarping Method /
Installation Method
Button
Front End Correction*
Back End Correction
Ceiling
Mount
Wall
Mount
Ceiling
Mount
Wall
Mount
Fisheye Source Image
-
-
√
√
Single ePTZ
√**
-
√
-
360°Panoramic
√
-
√
-
Quad View
√
-
√
-
180°Panoramic
-
√
-
√
Dual ePTZ
-
√
-
√
*If users are using the Front End Correction method for dewarping, the buttons
will only be shown when video format is set to H.264-2 or MJPEG on the home
page.
**If users are using the Front End Correction method, the Single ePTZ button
supported in Ceiling Mount installation is only available when the resolution of
the second stream is smaller than “960 x 960”.

10
2.1.2 Function Differences between Models
The table below shows the available function items seen on the home page for
different types of models. In the tables, model types are represented by
uppercase letters, and lens types are indicated by lowercase letters. The
supported function items for each model are marked by “√”.
A. Ultra High Definition Multiple Streams Micro Dome IP Camera
B.Ultra High Definition Multiple Streams IR Bullet IP Camera
C.Ultra High Definition Multiple Streams Box IP Camera
D.Ultra High Definition Multiple Streams ABF Box IP Camera
E. Ultra High Definition Multiple Streams Zoom AF Box IP Camera
F. Ultra High Definition Multiple Streams Compact Dome IP Camera
G.Ultra High Definition Multiple Streams Fisheye IP Camera
a. Varifocal Lens; b. Motorized Lens; c. Fixed-focal Lens; d. Wall Mount Installed;
e. Ceiling Installed; f. Zoom Lens
Model
Function
A
B
C
D
E
F
G
a
b
c
a
b
f
d
e
Multiple Language
√
√
√
√
√
√
√
√
√
√
√
√
Digital Zoom Control
√
√
√
√
√
√
√
√
√
√
√
√
Screen Size Adjustment
√
√
√
√
√
√
√
√
√
√
√
√
Talk (On / Off)
√
√
√
√
√
√
√
√
√
√
√
√
Speaker (On / Off)
√
√
√
√
√
√
√
√
√
√
√
√
Snapshot
√
√
√
√
√
√
√
√
√
√
√
√
Video Streaming Pause / Restart
√
√
√
√
√
√
√
√
√
√
√
√
Web Recording (On / Off)
√
√
√
√
√
√
√
√
√
√
√
√
Zoom
Adjustment
Tele/ Wide
-
-
√
√
-
-
√
-
√
√
-
-
Tele / Wide Steps
-
-
√
-
-
-
-
-
√
-
-
-
Reset
-
-
√
-
-
-
-
-
√
-
-
-
Manual
Focus
Adjustment
Near / Far
-
-
√
-
-
√
√
-
√
√
-
-
Near / Far Steps
-
-
√
-
-
√
-
-
√
-
-
-
Reset
-
-
√
-
-
√
-
-
√
-
-
-
Push AF
-
-
-
-
-
-
-
-
-
√
-
-
Auto Focus
Adjustment
Manual
-
-
-
-
-
-
√
-
-
√
-
-
Cont.
-
-
-
-
-
-
√
-
-
√
-
-
Zm Trig
-
-
-
-
-
-
√
-
-
√
-
-
Push AF
-
-
√
-
-
√
√
-
√
-
-
-
Fisheye Source Image
-
-
-
-
-
-
-
-
-
-
√
√
Dual ePTZ
-
-
-
-
-
-
-
-
-
-
√
-
180°Panoramic
-
-
-
-
-
-
-
-
-
-
√
-
Single ePTZ
-
-
-
-
-
-
-
-
-
-
-
√
360°Panoramic
-
-
-
-
-
-
-
-
-
-
-
√
Quad View
-
-
-
-
-
-
-
-
-
-
-
√

11
2.2 System
Under the tab <System>, there are submenus including: <System>, <Security>,
<Network>, <DDNS>, <Mail>, <FTP>, <HTTP>, <Events>, <Storage
Management>, <Recording>, <Schedule>, <File Location>, <Iris Adjustment>,
<View Information>, <Factory Default>, <Software Version>, <Software
Upgrade> and <Maintenance>.
NOTE: The <System> configuration page is only accessible to the
administrator.
2.2.1 System
The System setting can be found under the path: System> System.
Host Name
The name is for camera identification. If alarm function (refer to section
Application) is enabled and is set to send alarm message by Mail/FTP, the host
name entered here will be displayed in the alarm message. The maximum
length of the Host Name is 63 characters.
Time Zone
Select the time zone from the drop-down menu according to the location of the
camera.
Enable Daylight Saving Time
To enable DST, check the item and then specify time offset and DST duration.
The format for time offset is [hh:mm:ss]; for instance, if the amount of time offset
is one hour, enter “01:00:00” into the field.
Time format
Choose a time format (yyyy/mm/dd or dd/mm/yyyy) from the drop-down menu.
The format of date and time displayed above the live video window will be
changed according to the selected format.

12
Sync with Computer Time
Select the item, and the video date and time will synchronize with the date and
time of the PC.
NOTE: Users MUST click on the <Save> button to confirm the setting.
Otherwise the time will not be synced.
Manual
In this item, the administrator can set the video date and time manually. Entry
format should be identical with the examples shown next to the enter fields.
Sync with NTP server
Network Time Protocol (NTP) is an alternate way to synchronize the camera’s
clock with a NTP server. Specify the server that is to be synchronized with in the
entry field. Then select an update interval from the drop-down menu. For further
information about NTP, please refer to the web site: www.ntp.org.
NOTE: The synchronization will be done every time the camera boots
up.
Click on <Save> to save the settings.

13
2.2.2 Security
The Security setting can be found under this path: System> Security.
Click on the <Security> category; there will be a drop-down menu with tabs
including <User>, <HTTPS>, <IP Filter> and <IEEE 802.1X>.
2.2.2.1 User
The User setting can be found under this path: System> Security> User.
Admin Password
This item is for the administrator to reset a password. Enter the new password
in <Admin password> and <Confirm password>. The maximum length is 14
characters. The input characters / numbers will be displayed as dots for security
purposes. Click on <Save> to confirm the changes. After the changes are
confirmed, the web browser will ask the administrator to re-login to the camera
with the new password.
NOTE: The following characters are valid: A-Z, a-z, 0-9, !#$%&’-.@^_~.
Add User
This item is for the administrator to add new users. Enter the new user’s name
in <User name> and the password in <User password>. Usename can be up to
16 characters, and the maximum length of the password is 14 characters. Tick
the boxes below to give privileges for functions, including “Camera control”,
“Talk” and “Listen”. Click on <Add> to add the new user. The name of the new
added user will be displayed in the <User name> drop-down list. There is a
maximum of twenty user accounts.
I/O access
This item supports fundamental functions that enable users to view the
live video when accessing to the camera.
Camera control
This item allows the appointed user to change camera parameters on
the camera setting page.

14
Talk/Listen
Talk and Listen functions allow the appointed user in the local site (PC
site) communication with, for instance, the administrator in the remote
site.
Manage User
Delete user
Pull down the <User name> drop-down list and select the username to
delete. Click on <Delete> to remove the selected name.
Edit user
Pull down the <User name> drop-down list and select a username. Click
on <Edit> and a popup window will appear. In that window, enter the
new user password and reset the privileges. Click on <Save> to confirm
the changes. Then click on <Close> to complete the editing.
Streaming Authentication Setting
This setting provides security against unauthorized users getting streaming via
Real Time Streaming Protocol (RTSP). If the setting is enabled, users will be
requested to enter user name and password before viewing the live streams.
There are three security modes available: Disable, Basic and Digest. Refer to
the descriptions below for more details.
Disable
If disable mode is selected, there will be no security provided against
unauthorized access. Users will not be asked to input user name and
password for authentication.
Basic
This mode can only provide basic protection for the live streams.
There will still be risks for the password being intercepted.
Digest
Digest mode is a safer option for protection. The password is sent in an
encrypted format to prevent it from being stolen.
NOTE: Users MUST click on the <Save> button to apply the setting.

15
2.2.2.2 HTTPS
The HTTPS setting can be found under this path: System> Security> HTTPS.
HTTPS allows secure connections between the IP camera and web browser
using <Secure Socket Layer (SSL)> or <Transport Layer Security (TLS)>, which
ensure camera settings or username/password info from eavesdropping. It is
required to install a self-signed certificate or a CA-signed certificate for
implementing HTTPS.
To use HTTPS on the IP camera, an HTTPS certificate must be installed. The
HTTPS certificate can be obtained by either creating and sending a certificate
request to a Certificate Authority (CA) or creating a self-signed HTTPS
certificate, as described below.
Create Self-signed Certificate
Before a CA-issued certificate is obtained, users can create and install a
self-signed certificate.
Click on <Create> and provide the requested information to install a self-signed
certificate for the camera. Please refer to the last part of the section Provide the
Certificate Information for more details.
NOTE: The self-signed certificate does not provide the same high level
of security as when using a CA-issued certificate.
Install Signed Certificate
Click on the <Create Certificate Request> button to create and submit a
certificate request in order to obtain a signed certificate from CA.
Provide the requested information in the create dialog. Please refer to the
following section Provide the Certificate Information for more details.
When the request is complete, the subject of the Created Request will be shown
in the field. Click on <Properties> below the Subject field, copy the
PEM-formatted request and send it to the selected CA.
When the signed certificate is returned, install it by uploading the signed
certificate.

16
Provide the Certificate Information
To create a Self-signed HTTPS Certificate or a Certificate Request to CA, enter
the information as requested.
Create Self Signed Certificate
Create Certificate Request
Country
√
√
State or Province
√
√
Locality
√
√
Organization
√
√
Organizational Unit
√
√
Common Name
√
√
Valid Day
√
-
Country
Enter a 2-letter combination code to indicate the country which the
certificate will be used in. For instance, type in “US” to indicate United
States.
State or province
Enter the local administrative region.
Locality
Enter other geographical information.
Organization
Enter the name of the organization to which the entity identified in
“Common Name” belongs.
Organization Unit
Enter the name of the organizational unit to which the entity identified in
“Common Name” belongs.
Common Name
Indicate the name of the person or other entity that the certificate
identifies (often used to identify the website).
Valid days
Enter the period in days (1 to 9999) to indicate the valid period of
certificate.
Click on <OK> to save the Certificate Information after complete.

17
2.2.2.3 IP Filter
The IP Filter setting can be found under this path: System> Security> IP Filter.
With IP Filter, users can allow or deny specific IP addresses from accessing the
camera.
Enable IP Filter
Check the box to enable the IP Filter function. Once enabled, the listed
IP addresses (IPv4) in the <Filtered IP Addresses> list box will be
allowed/denied access to the camera.
Select <Allow> or <Deny> from the drop-down list and click on the
<Apply> button to determine the IP filter behavior.
Add IP Address
Input IP address at the blank space below the <Filtered IP Address> list
and click <Add>. The newly-added address will be shown in the list. Up
to 256 IP address entries can be specified.
In addition, to filter a group of IP addresses, enter an address at the
blank space followed with a slash and a number ranging from 1 to 31, ex.
192.168.2.81/30. The number after the slash defines how many IP
addresses will be filtered. For details, refer to the following example.
Example: Filtering a group of consecutive IP addresses.
The steps below show what will be filtered when 192.168.2.81/30 is
entered.
Step 1: Convert 192.168.2.81 to binary numbers. The binary
numbers are 11000000.10101000.00000010.01010001. Users can
refer to Appendix B: IP Addresses from Decimal to Binary for
converting the IP addresses to binary numbers. The number “30”
after the slash is referring to the first 30 digits of the binary numbers.

18
Step 2: Convert a few IP addresses before and after 192.168.2.81
to binary numbers. Then compare their first 30 digits to the binary
numbers of 192.168.2.81.
a. Convert 192.168.2.80 to binary numbers. The binary numbers
are 11000000.10101000.00000010.01010000. The first 30
digits are the same with the binary numbers of 192.168.2.81,
thus 192.168.2.80 will be filtered.
b. Convert 192.168.2.79 to binary numbers. The binary numbers
are 11000000.10101000.00000010.01001111. The first 30
digits are different than the binary numbers of 192.168.2.81,
thus 192.168.2.79 will not be filtered. This also means the IP
addresses before 192.168.2.79 will not be filtered. Therefore,
users can stop converting the IP addresses before
192.168.2.79 to binary numbers.
c. Repeat the same procedure in “a” with the IP addresses
after 192.168.2.81. Stop when the situation occurs in “b”
happens, that is, the 30th digit of the binary numbers of IP
address 192.168.2.84 is different, and will not be filtered.
As a result, the IP addresses 192.168.2.80 to 192.168.2.83 will be
filtered when entering 192.168.2.81/30. The following table clearly
shows the 30th digit of the binary numbers of IP addresses
192.168.79 and 192.168.84 is different from the others. Therefore,
these two IP addresses will not be filtered.
IP Addresses
Binary Numbers
192.168.2.79
11000000.10101000.00000010.01001111
192.168.2.80
11000000.10101000.00000010.01010000
192.168.2.81
11000000.10101000.00000010.01010001
192.168.2.82
11000000.10101000.00000010.01010010
192.168.2.83
11000000.10101000.00000010.01010011
192.168.2.84
11000000.10101000.00000010.01010100
Delete IP Address
To remove an IP address from the list, select the IP and click on
<Delete>.

19
2.2.2.4 IEEE 802.1X
The IEEE 802.1X setting can be found under this path: System> Security>
IEEE 802.1X.
The camera is allowed to access a network protected by 802.1X/EAPOL
(Extensible Authentication Protocol over LAN).
Users need to contact the network administrator to gain certificates, user IDs
and passwords.
CA Certificate
The CA certificate is created by the Certification Authority for the purpose of
validation. Upload the certificate for checking the server’s identity.
Client Certificate / Private Key
Upload the Client Certificate and Private Key for authenticating the camera
itself.
Settings
Identity
Enter the user identity associated with the certificate. Up to 16
characters can be used.
Private Key Password
Enter the password (maximum 16 characters) for user identity.
Enable IEEE 802.1X
Check the box to enable IEEE 802.1X.
Click on <Save> to save the IEEE 802.1X/ EAP- TLS setting.