Vicon VC-600W User manual

VC-600W, VC-600WS
VC-610W, VC-610WS SERIES
COLOR DOME CAMERAS
About this manual
INSTRUCTION MANUAL XX173-02
Before installing and using the camera, please read this manual
carefully. Be sure to keep it handy for later reference.
This installation should be made by a qualified service person and
should conform to the National Electric Code, ANSI/NFPA 70 and
all local codes.
CAMERA DIMENSIONS in. (mm)

Before sending the camera out for repair, check the items below.
If the problem persists after checking these items, contact
your service center.
■If no image appears
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been
adjusted correctly (with the level volume) ?
Is there adequate illumination?
■If the image is unclear
Is the lens in focus?
Is the lens dirty?
Dirt or fingerprints on the lens can adversely affect the
images. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
fluid (commercially available).
Is the monitor adjusted correctly?
PRECAUTIONS
■Do not open or modify
Do not open the case except during maintenance and
installation, as it may be dangerous and cause damage.
■Do not put objects inside the unit
Make sure that no metal objects or flammable substances get
inside the camera. It could cause fire, short-circuits or damages.
■Be careful when handling the unit
To prevent damage, do not drop the camera or subject it to strong shock or vibration.
■Install away from electric or magnetic fields
■Protect from humidity and dust
■Protect from high temperature
Be careful when installing close to the ceiling, in a kitchen or boiler room, as the
temperature may rise to high levels.
■Cleaning
Dirt can be removed from the case only by wiping it with a soft cloth moistened
with a soft detergent solution.
■Mounting Surface
The mounting surface material must be strong enough to support the camera.
TROUBLESHOOTING

SPECIFICATION VC-600W/VC-600WS
SPECIFICATION VC-610W/VC-610WS
GENERAL Spec NTSC PAL
HQ Interline Transfer CCD 1/3" 410K Pixels Color 1/3" 470K Pixels Color
Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V)
Scanning System 525 Lines 625 Lines
Horizontal Resolution
Sensitivity to Light [30IRE]
Gamma Correction
Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]
S/N Ratio
Synchronization
Video Output
Control DIP Switch
BLC
ME/AE
ATW/AWB
AGC
Electrical Spec
Operating Voltage
Power Consumption
Mechanical Spec
Operation Temp
Air Humidity
Lens Mount
Connections via
550TV Lines
0.03fc, 0.3Lux(Scene) With F1.2 Lens
0.45
> 48dB [AGC off]
Internal (12VDC) / External (Line Lock, 24VAC)
1.0Vp-p/75ohm Composite
DIP Switch Select ON/OFF
DIP Switch Select ME/AE (ON/OFF)
DIP Switch Select ATW/AWB (ON/OFF)
DIP Switch Select ON/OFF
12VDC(11-20V), 24VAC(20-27V)
12VDC -2.3W, 24VAC - 2.6W
14°F ~ 131°F ( -10°C ~ +55°C )
Up to max.90%
3.3-12mm
BNC(VIDEO), 2P WIRE(Power)
GENERAL Spec NTSC PAL
CCD Type 1/3" 410K Pixels Color 1/3" 470K Pixels Color
Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V)
Scanning System 525 Lines 625 Lines
Horizontal Resolution
Sensitivity to Light [30IRE]
Gamma Correction
Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]
S/N Ratio
Synchronization
Video Output
Control DIP Switch
ME/AE
ATW/AWB
WDR ON/OFF
AGC MAX ON
Electrical Spec
Operating Voltage
Power Consumption
Mechanical Spec
Operation Temp
Air Humidity
Lens Mount
Connections via BNC(VIDEO), 2P WIRE(Power)
0.45
0.06fC, 0.6Lux(Scene) With F1.2 Lens
480TV Lines
1.0Vp-p/75ohm Composite
Internal (12VDC) / External (Line Lock, 24VAC)
> 45dB [AGC off]
12VDC -3.9W, 24VAC - 4.0W
12VDC(11-20V), 24VAC(20-27V)
3.3-12mm
DIP Switch Select ATW/AWB (ON/OFF)
DIP Switch Select ME/AE (ON/OFF)
Up to max.90%
14°F ~ 131°F ( -10°C ~ +55°C )
DIP Switch Select ON/OFF
DIP Switch Select WDR (ON/OFF)

SPECIFICATION VC-600WDN/VC-600WDN-S
SPECIFICATION VC-600WIR/VC-600WIR-S
GENERAL Spec NTSC PAL
HQ Interline Transfer CCD 1/3" 410K Pixels Color 1/3" 470K Pixels Color
Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V)
Scanning System 525 Lines 625 Lines
Horizontal Resolution
Sensitivity to Light [30IRE]
Gamma Correction
Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]
S/N Ratio
Synchronization
Video Output
Control DIP Switch
BLC
ME/AE
ATW/AWB
AGC
Electrical Spec
Operating Voltage
Power Consumption
Mechanical Spec
Operation Temp
Air Humidity
Lens Mount
Connections via
14°F ~ 131°F ( -10°C ~ +55°C )
Up to max.90%
3.3-12mm
BNC(VIDEO), 2P WIRE(Power)
DIP Switch Select ATW/AWB (ON/OFF)
DIP Switch Select ON/OFF
12VDC(11-20V), 24VAC(20-27V)
12VDC -2.3W, 24VAC - 2.6W
Internal (12VDC) / External (Line Lock, 24VAC)
10Vp-p/75ohm Composite
DIP Switch Select ON/OFF
DIP Switch Select ME/AE (ON/OFF)
550TV Lines
0.04fc, 0.4Lux(Scene) With F1.2 Lens
0.45
> 48dB [AGC off]
GENERAL Spec NTSC PAL
HQ Interline Transfer CCD 1/3" 410K Pixels Color 1/3" 470K Pixels Color
Total Number of Pixels 811(H) x 508(V) 795(H) x 596(V)
Scanning System 525 Lines 625 Lines
Horizontal Resolution
Sensitivity to Light [30IRE]
Gamma Correction
Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]
S/N Ratio
Synchronization
Video Output
Control DIP Switch
BLC
ME/AE
ATW/AWB
AGC
Electrical Spec
Operating Voltage
Power Consumption
Mechanical Spec
Operation Temp
Air Humidity
Lens Mount
Connections via
550TV Lines
(BW, No LED) 0.04fc, 0.4Lux(Scene) With F1.2 Lens
0.45
> 48dB [AGC off]
Internal (12VDC) / External (Line Lock, 24VAC)
10Vp-p/75ohm Composite
DIP Switch Select ON/OFF
DIP Switch Select ME/AE (ON/OFF)
DIP Switch Select ATW/AWB (ON/OFF)
DIP Switch Select ON/OFF
12VDC(11-20V), 24VAC(20-27V)
MAX LED ON (12VDC - 4.6W, 24VAC - 4.7W)
14°F ~ 131°F ( -10°C ~ +55°C )
Up to max.90%
3.3-12mm
BNC(VIDEO), 2P WIRE(Power)

■LENS ADJUSTMEN
T
VC-600W/VC-600WS, VC-610W/VC-610WS, VC-600WDN/VC-600WDN-S
VC-600WIR/VC-600WIR-S
■CONNECTION
LENS ADJUSTMENT AND CONNECTION
1. Adjust the panning (360˚) and tilt (51˚) position.
2. Set the zoom position by using Zoom Lever Screw.
3. Set the focus by using Focus Lever Screw.
4. Loosen set screws to adjust roll
(turns camera position top/bottom).
CAUTION
Check for polarity when using a 12VDC power supply.
Input Voltage : 12VDC/24VAC
CLASS 2 NOT WET, CLASS 3 WET
1. Adjust the panning (360˚) and tilt (60˚) position.
2. Set the zoom position by using Zoom Lever Screw.
3. Set the focus by using Focus Lever Screw.
4. Loosen set screws to adjust roll
(turns camera position top/bottom).
PAN - 360˚
TILT - 60˚
Zoom
Focus
Set Screw
(2x)
°
TILT - 51˚
PAN - 360˚
12VDC Red (+)
Black (-)
24VAC

■VC-600W, VC-600WS
①DIP Switch Functions
(1) Compensating for backlight
ON When backlight is too bright
OFF Normal setting
CAUTION : It will be correctly set by adjusting level volume 5.
(2) Confirming the iris setting
ME(ON) When DC autoiris lens installed
AE(OFF) When fixed iris lens is installed
(3) White balance setting
ATW(ON) Use this under light source below 2500K and
over 9500K of Natrium (Sodium) low
color temperature light
AWB(OFF) Use this under light source between 2500K
and 9500K of fluorescent lamp or
incandescent light
(4) Setting gain control (AGC)
For adjusting the sensitivity of the camera.
Use this setting for shooting in dark environments.
ON Normal setting
OFF Set this when there is excessive noise
②Second Video OUT Connector (Option)
If installer is setting with portable monitor, this connector is used.
Be sure to terminate the last video device at 75 ohms.
③IR LED Connector (Option)
If extra IR LED board is attached, this connector is used.
CAMERA SETTINGS
② PORTABLE
MONITOR
③ IR LED ④ LINE LOCK
ADJUSTMENT
DC LENS
CONTROL
⑥ DC
VARIFOCAL
⑦ POWER
CONNECTOR
①
⑤

④Setting Monitor Synchronization (24 VAC adaptor users)
The camera offers V-phase adjustment over 360°. Vertical
sync disturbance may occur when a switcher is used to switch
between multiple cameras connected to one monitor.
To prevent vertical sync disturbance, adjust ④*.
CAUTION: When using the 12 VDC adaptor, sync setting is
set to internal sync.
⑤Adjusting Level Volume
If the entire image is too dark or bright, or the bakclight
compensation is not correct even after ①is set to "ON",
you need to adjust the level volume.
CCW (LOW) Closes the lens iris, making the entire image darker
CW (HIGH) Opens the lens iris, making the entire image brighter
⑥DC Varifocal Connector
This should be used with ⑤DC IRIS LENS.
⑦Power connector
Connect with AC/DC power, board attached inside.
*Before making any adjustment, confirm that the cameras are connected
to the power supply with the same polarity.
To make an adjustment: While observing the video outputs from
the cameras on an oscilloscope, press the first camera's V-phase
pushbutton. Until vertical sync from all cameras are in phase.
If the first camera's adjustment phase is insufficient, adjust the second
camera's V-phase contol in the oppposite direction until they are in phase.
■VC-610W, VC-610WS : WDR SETTING
⑤ DC LENS
CONTROL
④ LINE LOCK
ADJUSTMENT
② PORTABLE
MONITOR
⑥ DC
VARIFOCAL
③ IR LED
OFF ON
1 AE/ME AE ME
2ATW/AWBAWBATW
3 WDR OFF ON
4 AGC MAX OFF ON
NO FUNCTION DIP S/W
⑦ POWER
CONNECTOR

①DIP Switch Functions
(1) Confirming the iris setting
ME(ON) When DC autoiris lens installed
AE(OFF) When fixed iris lens is installed
(2) White balance setting
ATW(ON) Use this under light source below 2500K and
over 9500K of Natrium (Sodium) low
color temperature light
AWB(OFF) Use this under light source between 2500K
and 9500K of fluorescent lamp or
incandescent light
(3) WDR mode
ON Wide dynamic function is working
OFF Wide dynamic function is not working
(4) Setting gain control (AGC)
For adjusting the sensitivity of the camera.
Use this setting for shooting in dark environments.
ON Normal setting
OFF Set this when there is excessive noise
②Second Video OUT Connector (Option)
If installer is setting with portable monitor, this connector is used.
Be sure to terminate the last video device at 75 ohms.
③IR LED Connector (Option)
If extra IR LED board is attached, this connector is used.
④Setting Monitor Synchronization (24 VAC adaptor users)
The camera offers V-phase adjustment over 360°. Vertical
sync disturbance may occur when a switcher is used to switch
between multiple cameras connected to one monitor.
To prevent vertical sync disturbance, adjust ④*.
CAUTION: When using the 12 VDC adaptor, sync setting is
set to internal sync.
⑤Adjusting Level Volume
If the entire image is too dark or bright, or the bakclight
compensation is not correct even after ①is set to "ON",
you need to adjust the level volume.
CCW (LOW) Closes the lens iris, making the entire image darker
CW (HIGH) Opens the lens iris, making the entire image brighter
⑥DC Varifocal Connector
This should be used with ⑤DC IRIS LENS.
⑦Power connector
Connect with AC/DC power, board attached inside.

*Before making any adjustment, confirm that the cameras are connected
to the power supply with the same polarity.
To make an adjustment: While observing the video outputs from
the cameras on an oscilloscope, press the first camera's V-phase
pushbutton. Until vertical sync from all cameras are in phase.
If the first camera's adjustment phase is insufficient, adjust the second
camera's V-phase contol in the oppposite direction until they are in phase.
■VC-600WDN, VC-600WDNS, VC-600WIR, VC-600WIRS : TDN/IR SETTING
①DIP Switch Functions
(1) Compensating for backlight
ON When backlight is too bright
OFF Normal setting
CAUTION : It will be correctly set by adjusting level volume 5.
(2) Confirming the iris setting
ME(ON) When DC autoiris lens installed
AE(OFF) When fixed iris lens is installed
(3) White balance setting
ATW(ON) Use this under light source below 2500K and
over 9500K of Natrium (Sodium) low
color temperature light
AWB(OFF) Use this under light source between 2500K
and 9500K of fluorescent lamp or
incandescent light
(4) Setting gain control (AGC)
For adjusting the sensitivity of the camera.
Use this setting for shooting in dark environments.
ON Normal setting
OFF Set this when there is excessive noise
⑦
①
PORTABLE
MONITOR ②
③
④
⑤
⑥DC VARIFOCAL
LINE LOCK
ADJUSTMENT

②Second Video OUT Connector (Option)
If installer is setting with portable monitor, this connector is used.
Be sure to terminate the last video device at 75 ohms.
③IR LED Connector (Option)
If extra IR LED board is attached, this connector is used.
④Setting Monitor Synchronization (24 VAC adaptor users)
The camera offers V-phase adjustment over 360°. Vertical
sync disturbance may occur when a switcher is used to switch
between multiple cameras connected to one monitor.
To prevent vertical sync disturbance, adjust ④*.
CAUTION: When using the 12 VDC adaptor, sync setting is
set to internal sync.
⑤Adjusting Level Volume
If the entire image is too dark or bright, or the bakclight
compensation is not correct even after ①is set to "ON",
you need to adjust the level volume.
CCW (LOW) Closes the lens iris, making the entire image darker
CW (HIGH) Opens the lens iris, making the entire image brighter
⑥DC Varifocal Connector
This should be used with ⑤DC IRIS LENS.
⑦Power connector
Connect with AC/DC power, board attached inside.
*Before making any adjustment, confirm that the cameras are connected
to the power supply with the same polarity.
To make an adjustment: While observing the video outputs from
the cameras on an oscilloscope, press the first camera's V-phase
pushbutton. Until vertical sync from all cameras are in phase.
If the first camera's adjustment phase is insufficient, adjust the second
camera's V-phase contol in the oppposite direction until they are in phase.