Vicon CE202D-WN User manual

www.vicon-security.com
XX269-00-00
CE202D-WN Network Outdoor
Camera Dome
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the
operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed
to be used in life-critical situations and must not be used for this purpose.
Vicon Industries Inc.
Tel: [phone] Fax: [phone] Toll Free: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300
Document Number: 8009-8269-00-00
3URGXFWVSHFL¿FDWLRQVVXEMHFWWRFKDQJHZLWKRXWQRWLFH
Issued: 214
&RS\ULJKW9LFRQ,QGXVWULHV,QF$OOULJKWVUHVHUYHG
Installation Guide

2
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION
GRILLS OR OTHER OPENINGS ON THE EQUIPMENT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous voltage" within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
PRECAUTIONS
Safety -------------------------------------- Installation -------------------------------
Should any liquid or solid object fall into the cabinet,
unplug the unit and have it checked by the qualified
personnel before operating it any further.
Unplug the unit from the wall outlet if it is not going to
be used for several days or more. To disconnect the
cord, pull it out by the plug. Never pull the cord itself.
Allow adequate air circulation to prevent internal heat
build-up. Do not place the unit on surfaces (rugs,
blankets, etc.) or near materials(curtains, draperies)
that may block the ventilation holes.
Height and vertical linearity controls located at the rear
panel are for special adjustments by qualified
personnel only.
Do not install the unit in an extremely hot or humid
place or in a place subject to excessive dust,
mechanical vibration.
The unit is not designed to be waterproof.
Exposure to rain or water may damage the unit.
Cleaning ---------------------------------
Clean the unit with a slightly damp soft cloth.
Use a mild household detergent. Never use strong
solvents such as thinner or benzene as they might
damage the finish of the unit.
Retain the original carton and packing materials for
safe transport of this unit in the future.

3
FCC COMPLIANCE STATEMENT
INFORMATION TO THE USER:
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO
COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC
RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL
INTERFERENCE WHEN THE EQUIPMENT IS OPERATED I
N A COMMERCIAL ENVIRONMENT. THIS
EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT
INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS.
CAUTION:CHANGES OR MODIF
ICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO OPERATE THE
EQUIPMENT.
HIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.
CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME À LA NORME NMB-003 DU CANADA.
CE COMPLIANCE STATEMENT
WARNING: This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

4
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong is provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for
long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been moisture, does not
operate normally, or has been dropped.
15. CAUTION –THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED
SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO
NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE
OPERATING INSTRUCTIONS UNLESS YOU QRE QUALIFIED TO DO SO.
16. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2
power source only.
17. ITE is to be connected only to PoE networks without routing to the outside plant.

5
Contents
1. Description ------------------------------------------------------------------6
1.1 Components-- ------------------------------------------------------------------------------------------- 6
1.2 Key Features - ------------------------------------------------------------------------------------------- 7
2. Installation -- ---------------------------------------------------------------- 8
2.1 Camera Installation ---- -------------------------------------------------------------------------------- 8
2.2 Connections -- ------------------------------------------------------------------------------------------- 9
2.3 Network Connection and IP Assignment ----------------------------------------------------------- 11
3. Operation -------------------------------------------------------------------- 12
3.1 Access from a browser --------------------------------------------------------------------------------- 12
3.2 Access from the internet ------------------------------------------------------------------------------- 13
3.3 Setting the admin password over a secure connection ------------------------------------------- 13
3.4 Live View Page------------------------------------------------------------------------------------------- 14
3.5 Network Camera Setup--------------------------------------------------------------------------------- 16
3.5.1 Basic Configuration------------------------------------------------------------------------------ 16
1) Users ------------------------------------------------------------------------------------------- 17
2) Network --------------------------------------------------------------------------------------- 18
3) Video & Image ------------------------------------------------------------------------------- 19
4) Audio------------------------------------------------------------------------------------------- 21
5) Date & Time ---------------------------------------------------------------------------------- 23
3.5.2 Live View ---------------------------------------------------------------------------------------- 24
3.5.3 Video & Image ----------------------------------------------------------------------------------- 25
3.5.4 Audio ------------------------------------------------------------------------------------------- 31
3.5.5 Event ------------------------------------------------------------------------------------------- 32
1) Event-In --------------------------------------------------------------------------------------- 32
2) Event-Out ------------------------------------------------------------------------------------- 38
3) Event Map------------------------------------------------------------------------------------- 45
3.5.6 System ------------------------------------------------------------------------------------------- 47
1) Information ----------------------------------------------------------------------------------- 47
2) Security ---------------------------------------------------------------------------------------- 48
3) Date & Time ---------------------------------------------------------------------------------- 51
4) Network --------------------------------------------------------------------------------------- 52
5) Language-------------------------------------------------------------------------------------- 62
6) Maintenance ---------------------------------------------------------------------------------- 63
7) Support ---------------------------------------------------------------------------------------- 64
3.6 Playback----------------------------------------------------------------------------------------------------67
3.7 Help ------------------------------------------------------------------------------------------------------- 69
3.8 Resetting to the factory default settings-------------------------------------------------------------- 70
4. Appendix -------------------------------------------------------------------- 71
4.1 Troubleshooting------------------------------------------------------------------------------------------- 71
4.2 Alarm Connection ----------------------------------------------------------------------------------------- 72
4.3 Preventive Maintenance --------------------------------------------------------------------------------- 72
4.4 Product Specification ------------------------------------------------------------------------------------- 73

6
1. Description
The information in this manual provides quick installation and setup procedures for the CE202D-WN
Camera Dome. These units should only be installed by a qualified technician using approved materials
in conformance with federal, state, and local codes. Read these instructions thoroughly before
beginning an installation. Always refer to Vicon’s website to assure you have the most up-to-date
manual, www.vicon-security.com.
The CE202D-WN is designed for demanding outdoor security installations. This cost-effective fixed
network camera includes an integral 3.7 mm megapixel fixed lens; the 1080p resolution delivers crisp
clear images. The CE202D-WN camera is fully compatible with all ViconNet® systems; its ONVIF
certification provides an open-platform for integration into other video management systems.
The network camera provides triple-streaming video and supports H.264 compression technology.
MPEG-4 and Motion JPEG (M-JPEG) compressions are also provided, as are privacy masking and
motion detection. Installation is made easy and cost-effective with Power-over-Ethernet (PoE); the
camera also accepts 12 VDC.
1.1 Components
The system comes with the following components:
Camera Unit Installation CD Installation Guide
Accessory Kit Template sheet Optional OSD Controller
Notes:
1. Check your package to make sure that you received the complete system, including all
components shown above.
2. Adapter for 12 VDC is not supplied and the optionalV920D-OSD OSD Controller can be purchased
separately.

7
1.2 Key Features
• Brilliant Video Quality
The network camera offers the highly efficient H.264 video compression, which drastically
reduces bandwidth and storage requirements without compromising image quality. Motion JPEG
is also supported for increased flexibility.
•Dual or Triple Streams
The network camera can deliver dual or triple video streams simultaneously at full frame rate in
all resolutions up to Full HD (1920 x 1080p) using Motion JPEG and H.264 (or MPEG-4). This
means that several video streams can be configured with different compression formats,
resolutions and frame rates for different needs.
• Image Setting Adjustment
The network camera enables users to adjust image settings such as contrast, brightness and
saturation to improve images before encoding takes place.
• Micro-SD Recording Support
The network camera supports a micro-SD memory slot for local recording with removable
storage.
• Improved Security
The network camera logs all user access, and lists currently connected users. Also, its full frame
rate video can be provided over HTTPS.
• Pan & Tilt Control via Network
The network camera also enables users to adjust pan and tilt remotely via the network.
•Megapixel Resolution
Max 30fps@1920x1080
•Power over Ethernet (PoE)
Support for Power over Ethernet (IEEE802.3af) enables the unit, as well as the camera module
that is connected to it, to receive power through the same cable as for data transmission. This
makes for easy installation since no power outlet is needed.
• ONVIF
This is a global interface standard that makes it easier for end users, integrators, consultants,
and manufacturers to take advantage of the possibilities offered by network video technology.
ONVIF enables interoperability between different vendor products, increased flexibility, reduced
cost, and future-proof systems.

8
2. Installation
2.1 Camera Installation
Carefully remove the contents from the box and verity that nothing was damaged in shipment.
1) Using the template sheet provided, make screw holes for camera on the ceiling.
2) Disassemble the camera by loosening the four (4) captive screws securing the cover and removing
the camera cover.
3) Secure the dome camera to the ceiling using the anchors (2x) and screws (2x) provided in the
accessory kit.
Camera Dimension
Dimensions Unit: mm

9
2.2 Connections
Connection Cable
NO Name Description
1 Micro-SD Slot Micro-SD memory slot
2
Factory Default Button
Button for the factory default setting
3 Mic Port
Microphone input header.
4 Service Monitor Port
Service Monitor (set to NTSC by default ; change video format
from Source menu); V920D-OSD Controller (option)
Communication Port, Mono Jack
NO Name Description
1 Audio Cable Audio line output, RCA Jack
2 Power Cable
Red: 12 VDC
White: GND
3 Alarm Cable
Blue: GND
Gray: ALARM INPUT
Brown: GND
Yellow : ALARM OUT
4 Ethernet Cable Ethernet, RJ-45 port compatible with 10/100Mbps; PoE
functionality. Modular Jack

10
• Connecting to the RJ-45
Connect a standard RJ-45 cable to the network port of the network camera. Generally a
cross-over cable is used for direct connection to a PC, while a direct cable is used for connection
to a hub.
Micro SD memory slot
Insert an SD memory card (customer supplied).
• Connecting the Power
Connect a 12 VDC power adaptor (customer supplied) to the camera.
• Connecting Service Monitor Port
The Service Monitor output port is located on the board of the dome camera and is used for easy
OSD setup.
▶ID & IP assignment
To make changes in the OSD menu, the optional V920D-OSD controller can be used to set
camera title and IP address.
1. Connect the OSD Controller to the Service Monitor port of the network camera.
2. Connect Service Monitor and the Video Output port of the OSD Controller.
3. Press the SET button on the controller to access the Main Menu.
4. Change camera ID and IP address as needed. Additionally, the Name (or title) of the camera
can be changed. Use the ↑↓←→ buttons on the controller to change the parameters.
5. Select SAVE or CANCEL to exit the Main Menu.
The Video Output can also be used for easy zoom and focus control when adjusting the lens.
Video Output is restricted to 704x480 (576) resolution.
▶Pan & Tilt Control
The camera enters Zoom and Focus control mode when the OSD Controller is connected to the
Service Monitor port.
-. Pan Control: ↑(Up), ↓(Down)
-. Tilt Control: ← (Left), → (Right)
Note: The optional V920D-OSD OSD Controller can be purchased separately.

11
2.3 Network Connection and IP assignment
The network camera is designed for use on an Ethernet network and requires an IP address for
access. Most networks today have a DHCP server that automatically assigns IP addresses to
connected devices. By the factory default, your camera is set to obtain the IP address automatically
via DHCP server. If your network does not have a DHCP server the network camera will use
192.168.1.100 as the default IP address.
If DHCP is enabled and the product cannot be accessed, run the “Smart Manager” utility on the CD to
search and allocate an IP address to your products, or reset the product to the factory default settings
and then perform the installation again.
1. Connect the network camera to the network and power up.
2. Start SmartManager utility (Start>All programs>SmartManager>SmartManager), the main
window displays. After a short while any network devices connected to the network will be
displayed in the list.
3. Select the camera on the list and click right button of the mouse. The pop-up menu below
displays.
4. Select Assign IP. The Assign IP window displays. Enter the required IP address.
Note: For more information, refer to the Smart Manger
User’s Manual.

12
3. Operation
The network camera can be used with Windows® operating system and browsers. The recommended
browsers are Internet Explorer®, Safari®, Firefox®, Opera® and Google Chrome® with Windows.
Note: To view streaming video in Microsoft® Internet Explorer, set your browser to allow ActiveX
controls.
Note: Some screens may appear different (i.e., color scheme) depending on the firmware version, but
the functionality is the same or similar.
3.1 Access from a browser
1. Start a browser (i.e., Internet Explorer).
2. Enter the IP address or host name of the network camera in the Location/Address field of your
browser.
3. A starting page displays. Click Live View, Playback or Setup to enter web page.
4. Click Live View for the network camera’s Live View page to appear in the browser.

13
3.2. Access from the internet
Once connected, the network camera is accessible on your local network (LAN). To access the
network camera from the Internet you must configure your broadband router to allow incoming data
traffic to the network camera. To do this, enable the NAT-traversal feature, which will attempt to
automatically configure the router to allow access to the network camera. This is enabled from Setup
> System > Network > NAT.
For more information, refer to “3.5.6 System>Network>NAT”of User’s Manual.
3.3 Setting the admin password over a secure connection
To gain access to the product, the password for
the default administrator user must be set. This
is done in the “Admin Password” dialog, which is
displayed when the network
camera is accessed
for the setup at the first time.
Enter your admin
name and passw
ord, set by the administrator.
Note:
The default administrator username is
“ADMIN” and password is “1234”. If the
password is lost, the network camera must be
reset to the factory default settings. See section
“3.8 Resetting to the Factory Default
Settings” for
more details
.
To prevent network eavesdropping when setting the admin password, it can be done via an encrypted
HTTPS connection, which requires an HTTPS certificate (see note below).
To set the password via a standard HTTP connection, enter it directly in the first dialog shown below.
To set the password via an encrypted HTTPS connection, see “3.5.5 System > Security > HTTPS”.
Note: HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt the traffic between
web browsers and servers. The HTTPS certificate controls the encrypted exchange of information.

14
3.4 Live View Page
The live view page comes in
several screen
modes
: 1920x1080, 1280x1024, 1280x720,
7
04x480(576), 640x480, 352x240 (288)
and
320x240. Select the most suitable
mode in accordance with your PC
specifications and monitoring purposes
.
1) General controls
Live View Page Search & Playback Page Setup Page Help Page
The video drop-down list allows you to select a customized or pre-programmed
video stream on the live view page. Stream profiles are configured under Setup > Basic
Configuration > Video & Image. For more information, see section “3.5.1 Basic Configuration >
Video & Image”of this user’s manual.
The resolution drop-down list allows the selection of the most suitable
video resolutions to be displayed on Live View page.
The protocol drop-down list allows the selection of the combination of
protocols and methods to use depending on your viewing requirements and on the properties of
the network.
2) Control toolbar
The live viewer toolbar is available on the web browser page only. It displays the following
buttons:
The Stop button stops the video stream being played. Pressing the key again toggles the
start and stop. The Start button connects to the network camera to start playing a
video stream.
The Pause button temporarily stops (pauses) the video stream being played.
The Snapshot button takes a picture (snapshot) of the current image. The location where
the image is saved can be specified.
The digital zoom activates a zoom-in or zoom-out function for video image on the live
screen.
The Full Screen button causes the video image to fill the entire screen area. No other
windows will be visible. Press the 'Esc' button on the computer keyboard to cancel full
screen view.
The Manual Trigger button activates a pop-up window to manually start or stop the event.

15
The PT button activates a pop-up window for Pan and Tilt control.
Use the speaker icon scale to control the volume of the speakers.
Use the microphone icon scale to control the volume of the microphone.
3) Video Streams
The network camera provides several image and video stream formats. Your requirements and
the properties of your network will determine the type you use.
The Live View page of the network camera provides access to H.264, MPEG-4 and Motion JPEG
video streams and to the list of available video streams. Other applications and clients can also
access these video streams/images directly, without going via the Live View page.
4) Pan and Tilt Control
Pan and Tilt can be controlled from the live view screen. Press the button on the left top in
the Live View screen to activate the control panel.
•Adjusting Pan and Tilt:
Click the navigation button in the PT control panel.
Pan Control: ►(Right), ◄(Left)
Tilt Control: ▲(Up), ▼(Down)

16
3.5 Network Camera Setup
This section describes how to configure the network camera and is intended for product
Administrators, who have unrestricted access to all the Setup tools, and Operators, who have access
to the settings for Basic, Live View, Video & Image and System Configuration.
The network camera is configured by clicking Setup in the top right-hand corner of the Live View page.
Click on to access the online help that explains the setup tools.
When accessing the network camera for the first time,
the “Admin Password” dialog appears. Enter your
admin name and password, set by the administrator.
Note: If the password is lost, the network camera must
be reset to the factory default settings. See “3.8
Resetting to the Factory Default Settings”. The default
administrator username is “ADMIN” and password is
“1234”.
3.5.1 Basic Configuration
The device information is displayed on this Basic Configuration page.

17
1) Users
User access control is enabled by default. An administrator can set up other users, by giving these
user names and passwords. It is also possible to allow anonymous viewer login, which means that
anybody may access the Live View page, as described below:
The User List displays the authorized users and user groups (levels):
User Group Authority
Guest Provides the lowest level of access, which only allows access to the
Live View page.
Operator
An operator can view the Live View page, create and modify
events, and adjust certain other settings. Operators have no access
to System Options.
Administrator An administrator has unrestricted access to the Setup tools and can
determine the registration of all other users.
An administrator can Add, Modify or Remove users in the list by clicking the appropriate button. Click
Save to save the settings or Reset to cancel.
Enable anonymous viewer login: Check the box to use the webcasting features. Refer to
“3.5.2 Video & Image” for more details.
Enable WS-Security: Do not check this box to connect and monitor the network camera
through Vicon’s viewing software using drivers older than 935.
Note: WS-Security is an open format for signing and encryption of message parts, for supplying
credentials in the form of security tokens, and for security passing those tokens in a message.

18
2) Network
The network camera supports both IP version 4 and IP version 6. Both versions may be enabled
simultaneously, and at least one version must always be enabled. When using IPv4, the IP address for
the network camera can be set automatically via DHCP, or a static IP address can be set manually.
If IPv6 is enabled, the network camera receives an IP address according to the configuration in the
network router. There is also the option of using the Internet Dynamic DNS Service. For more
information on setting the Network, refer to Setup> System>Security>Network.
• Obtain IP address via DHCP - Dynamic Host Configuration Protocol (DHCP) is a protocol
that lets network administrators centrally manage and automate the assignment of IP
addresses on a network. DHCP is enabled by default. Although a DHCP server is mostly
used to set an IP address dynamically, it is also possible to use it to set a static, known IP
address for a particular MAC address.
• Use the following IP address - To use a static IP address for the network camera,
check the radio button and then make the following settings:
- IP address - Specify a unique IP address for your network camera.
- Subnet mask - Specify the mask for the subnet the network camera is located on.
- Default router - Specify the IP address of the default router (gateway) used for
connecting devices attached to different networks and network segments.
Notes:
1. DHCP should only be enabled if using dynamic IP address notification, or if your DHCP server can
update a DNS server, which then allows you to access the network camera by name (host name).
If DHCP is enabled and you cannot access the unit, you may have to reset it to the factory
default settings and then perform the installation again.
2. The ARP/Ping service is automatically disabled two minutes after the unit is started, or
as soon as an IP address is set.
3. Pinging the unit is still possible when this service is disabled.

19
3) Video & Image
• Stream1 Setting
- Codec:
The codec settings are separated into MPEG4 and H.264.
H.264 is also known as MPEG-4 Part 10. This is the new generation compression standard for digital
video. This function offers higher video resolution than Motion JPEG or MPEG-4 at the same bit rate and
bandwidth, or the same quality video at a lower bit rate.
There are 4 pre-programmed stream profiles available for quick set-up.
Choose the form of video encoding to use from the drop-down list:
*H.264 HP (High Profile): The primary profile for broadcast and disc storage applications,
particularly for high-definition television applications (for example, this is the profile adopted
by the Blu-ray Disc storage format and the DVB HDTV broadcast service).
* H.264 MP (Main Profile):
Primarily for low-cost applications that require additional error robustness, this profile is used
rarely in videoconferencing and mobile applications; it does add additional error resilience
tools to the Constrained Baseline Profile. The importance of this profile is fading after the
Constrained Baseline Profile has been defined.
* H.264 BP (Baseline Profile):
Originally intended as the mainstream consumer profile for broadcast and storage
applications, the importance of this profile faded when the High Profile was developed for
those applications.

20
* MPEG4 SP (Simple Profile):
Mostly aimed for use in situations where low bit rate and low resolution are mandated by
other conditions of the applications, like network bandwidth, device size, etc.
- Resolution:
Resolution enables users to determine a basic screen size when having access through the
Web Browser or PC program. The screen size control comes in several modes, 1920x1080,
1280x720, 640x480, 352x240, and 320x240. Users can reset the selected screen size
anytime while monitoring the screen on a real-time basis.
- Bitrate control:
The bit rate can be set as Variable Bit Rate (VBR) or Constant Bit Rate (CBR). VBR adjusts
the bit rate according to the image complexity, using up bandwidth for increased activity in
the image, and less for lower activity in the monitored area.
CBR allows you to set a fixed target bitrate that consumes a predictable amount of
bandwidth. As the bit rate would usually need to increase for increased image activity, but in
this case cannot, the frame rate and image quality are affected negatively. To partly
compensate for this, it is possible to prioritize either the frame rate or the image quality
whenever the bit rate needs to be increased. Not setting a priority means the frame rate and
image quality are equally affected.
- Bitrate:
When it is necessary to adjust a smooth transmission status according to network situations,
users can increase the compressibility to carry out the network transmission stably.
Alternatively, when it is necessary to maintain a detailed monitoring screen by enhancing
the image quality, users can do so by decreasing the compressibility. In each case, adjust
this function according to the network status and monitoring purposes. The default is 2000
(Kbps).
- Frame rate:
Upon the real-time play, users should select a frame refresh rate per second. If the rate is
high, the image will become smooth. On the other hand, if the rate is low, the image will not
be natural but it can reduce a network load.
- GOP size:
Select the GOP (Group of Picture) size. If users want to have a high quality of fast image
one by one, decrease this value. For the purpose of general monitoring, do not change a
basic value. Such act may cause a problem to the system performance. Vicon recommends
that GOP be the same as the fps.