Videofied XMA User manual

Pointillés / Blitz Studio
Get Videofied.
Visit us at
www.videofied.com
USER GUIDE
Your local installer: www.eaglesecuritysolutions.co.uk

We recommend that you read this user manual carefully to ensure that your security system is
operated with maximum efficiency and in optimal conditions.
The VIDEOFIED®system complies with European radio standards and is designed to operate in
frequency ranges which are not harmful to the user.
English p. 1-12
Arming - Away 1-2
Arming - Stay 2
Disarming - Off 3-4
Activating Emergency Requests 4
Activate/Deactivate Chime 4
Partition Arming 5-6
Partition Disarming 6-7
Checking System Status 7
Direct Device Bypass 8
Activating Duress Signals 8-9
Managing Badges and Codes 9-11
Notes 12
1

3. Remote Control
Press the button and instantly release.
The remote control will beep twice in conrmation.
Note: A single low tone noties the command was not received at the
control panel. Move closer to the control panel and reattempt to arm the
system.
The exit delay starts and short beeps are emitted from the Remote
Control and internal sirens (if installed)
1. Keypad (XMA/WMB)
Code Arming (XMA/WMB):
 Enter access code and press or to conrm.
 The keypad display will show
Quick Arm (XMA/WMB):
 Press and hold until the keypad rapdily beeps three times.
 The keypad display will show
Keypad Badge Reader (WMB):
 Present the badge to the symbol on the keypad and hold it for 2 seconds.
 The keypad beeps once and shows a green LED to conrm.
 The keypad display will show
Note: Detection from an instant device during arming will stop the arming
process and display . Press to restart the arming process or
to bypass the device. If no command is registered the system will automatically
restart arming after 3 minutes.
 For all keypad arming options the exit delay starts and short beeps are
emitted from the keypad and internal sirens (if installed). At the end
of the exit delay the display shows and the LED on the
keypad ashes RED ever two seconds.
Arming - Away
SYSTEM ARMING AWAY
ENGLISH
DETECTION
"DEVICE NAME"
SYSTEM ARMED
ARMING THE SYSTEM
ARMING THE SYSTEM
1

2. Badge Reader (BR)
 Present the badge to the reader and hold for two (2) seconds.
 The reader will beep twice in acknowledgement.
 One red and one green LED will display on the reader and the exit
delay will start.
Note: Detection from an instant device or if there is a problem with arming the reader
will display two green LEDs for 5 seconds. Without action from the user the system will
attempt rearming in 3 minutes.
   Short beeps are emitted from the reader and internal sirens
(if installed). At the end of the time delay the system is armed and the
red LED on the reader ashes every two seconds.
Arming - Away Continued...
Arming - Stay
1. Keypad (XMA/WMB)
Code Arming (XMA/WMB):
 Enter access code and press
 The keypad display will show
Quick Arm (XMA/WMB):
 Press and hold until the keypad rapdily beeps three times.
 The keypad display will show
Keypad Badge Reader (WMB):
 Press the . Keypad will display
 Present the badge to the symbol on the keypad and hold it for 2 seconds.
 The keypad beeps once and shows a green LED to conrm.
 The keypad display will show
Note: Detection from an instant device during arming will stop the arming
process and display . Press to restart the arming process or
to bypass the device. If no command is registered the system will automatically
restart arming after 3 minutes.
 For all keypad arming options the exit delay starts and short beeps are
emitted from the keypad and internal sirens (if installed). At the end
of the exit delay the display shows and the LED on the
keypad ashes RED ever two seconds.
ARMING
SP1
SYSTEM ARMING
SP1
ARMING
SP1
ALARM SP1
BADGE OR CODE
DETECTION
"DEVICE NAME"
SYSTEM ARMED
ENGLISH
2 3

ENGLISH
2
1. Keypad (XMA/WMB)
No Event:
Code Disarming (XMA/WMB)
 Enter access code and press or to conrm.
 The keypad display will show
Quick Disarm (XMA/WMB):
 Press and hold until the keypad rapdily beeps three times.
 The keypad display will show
 Enter access code and press
 The keypad display will show
Keypad Badge Reader (WMB):
 Present the badge to the symbol on the keypad and hold it for 2 seconds.
 The keypad beeps once and shows a green LED to conrm.
 The keypad display will show
Event Acknowledgment: During disarming you must acknowledge any events
that have happened since the system was last armed.
 Perform any of the above disarming options
 The keypad display will show
 Press to acknowledge that the event has occured since last arming
 The keypad display will show
 Press , display will show
Disarming - Off
Mon 01/02 04:49
DISARMED LVL:1
"Event"
DISARMING
BADGE OR CODE
"Event"
"Device Name"
Mon 01/02 04:49
DISARMED LVL:1
Mon 01/02 04:49
DISARMED LVL:1
Mon 01/02 04:49
DISARMED LVL:1
2. Remote Control (RC)
 Press the button and instantly release after the rst beep
 The remote control will beep twice in conrmation
Note: A single low tone noties the command was not recieved at
the control panel. Move closer to the control panel and reattempt to
disarm the system.
 The system is disarmed.
3

1. Keypad (XMA/WMB)
Press the button for 3 seconds.
They Keypad display ashes for 10 seconds.
Press the desired emergency button.
Display shows
A valid user code or badge for the system must be used to
clear the event.
3. Badge Reader (BR)
Present the badge to the reader and hold for 2 seconds.
The reader will beep twice in acknowledgement.
No Event:
Two green LEDs will light up and the system is disarmed.
Event Acknowledgment:
The top LED will blink twice and the reader will beep 4 times
to indicate an event has occured since the last arming.
The system is disarmed.
Disarming - Off - Continued
Activating Emergency Requests
Police Emergency Medical Emergency
Fire Emergency
POLICE
BADGE OR CODE
Activate/Deactivate Chime
1. Keypad (XMA/WMB)
Press and hold the button until the keypad beeps rapidly
three times.
They display will show or .
*The chime function will only sound through an indoor siren that is learned into the
system*
CHIME
ACTIVATED
CHIME
DEACTIVATED
ENGLISH
4 5

ENGLISH
1. Keypad (XMA/WMB)
Code Partition Arming (XMA/WMB)
 Press until the desired partition is shown
 Enter a user code and press
 The system displays
Note: Detection from an instant device during arming will stop the arming process and
display . You may press to retry the arming or to bypass the device.
If no command is registered the system will automatically retry arming after 3 minutes.
 The exit delay starts and short beeps are emitted from the keypad and
internal sirens (if installed). At the end of the exit delay the red LED on the
keypad ashes every two seconds.
Keypad Badge Reader Partition Arming (WMB):
 Press until the desired partition is shown
 Present the badge to the symbol on the keypad and hold it for 2
seconds.
 The keypad beeps once and shows a green LED to conrm.
 The keypad display will show
Note: Detection from an instant device during arming will stop the arming
process and display . Press to restart the arming process or
to bypass the device. If no command is registered the system will automatically
restart arming after 3 minutes.
 For all keypad arming options the exit delay starts and short beeps are
emitted from the keypad and internal sirens (if installed). At the end
of the exit delay the display shows what partitions and what mode
they have been armed in and the LED on the
keypad ashes RED ever two seconds.
2. Remote Control (RC)
Note: Remote Controls are congured during installation to use specc partitions. There is no option to choose
which partition to arm on the Remote Control.
 Press the button and instantly release.
 The remote control will beep twice in conrmation and the exit delay starts.
Note: A single low tone noties the command was not recieved at
the control panel. Move closer to the control panel and reattempt to
disarm the system.
 The system is armed for the parition(s) the device is set.
Partition Arming
ARMING
A A - -
DETECTION
"DEVICE NAME"
ARMING
A A - -
DETECTION
"DEVICE NAME"
Thu 05/13 14:24
PA1=A PA2=A L:1s
5

ENGLISH
Partition Arming - Continued
3. Badge Reader (BR)
Note: Badges are congured during installation to use specc partitions. There is no option to choose
which partition to arm with the Badge Reader. 
 Present the badge to the reader and hold for two (2) seconds.
 The reader will beep twice in acknowledgement.
 One red and one green LED will display on the reader and the exit
delay will start.
Note: Detection from an instant device or if there is a problem with arming the
reader will display two green LEDs for 5 seconds. Without action from the user
the system will attempt rearming in 3 minutes.
   Short beeps are emitted from the reader and internal sirens
(if installed). At the end of the time delay the system is armed and the
red LED on the reader ashes every two seconds.
Partition Disarming
1. Keypad (XMA/WMB)
No Event:
Partition Code Disarming (XMA/WMB)
 Press until the desired partition to be disarmed is shown
 Enter access code and press or to conrm.
 The keypad display will show
Keypad Badge Reader Partition Disarming (WMB)
 Press until the desired partition to be disarmed is shown
 Present the badge to the symbol on the keypad and hold it for 2
seconds.
 The keypad beeps once and shows a green LED to conrm.
 The keypad display will show
Event Acknowledgment: During disarming you must acknowledge any events
that have happened since the system was last armed.
 Perform any of the above disarming options
 The keypad display will show
 Press to acknowledge that the event has occured since last arming
 The keypad display will show
 Press , display will show
Mon 01/02 04:49
DISARMED LVL:1
Mon 01/02 04:49
DISARMED LVL:1
"Event"
"Event"
"Device Name"
Mon 01/02 04:49
DISARMED LVL:1
6 7

ENGLISH
2. Remote Control (RC)
Note: Remote Controls are congured during installation to use specc partitions. There is no option to choose which
partition to disarm on the Remote Control.
 Press the button and instantly release.
 The remote control will beep twice in conrmation
Note: A single low tone noties the command was not recieved at
the control panel. Move closer to the control panel and reattempt to
disarm the system
 The system is disarmed for the parition(s) the device is set
Partition Disarming - Continued
3. Badge Reader (BR)
Note: Badges are congured during installation to use specc partitions. There is no option to choose
which partition to disarm on the Badge Reader. 
 Present the badge to the reader and hold for two (2) seconds
 The reader will beep twice in acknowledgement
 Two green LEDs will light up and the system will be disarmed
Event Acknowledgment: Perform the above steps and the top LED will blink twice
and the reader will beep 4 times to indicate that there has been an event since
arming and then system will be disarmed.
ARMING BYPASS
SYSTEM
Checking System Status
1. Keypad (XMA/WMB)
Press and hold the button until the keypad beeps rapidly
three times
The display will show devices that are in trouble,
communication methods that are enabled but have
problems or that the system is Ready To Arm if no faults are
found. Use the arrow keys to scroll through all devices that
are in trouble or press to exit back to the main screen
READY TO ARM
ETHERNET BAD 2G3G BAD
DEVICE TAMPER
SUPERVISION PROBLEM
There are no Faults found
Issue with the communication method
Displayed device is in tamper
Displayed device is not communicating with the
control panel
SUPERVISION PROBLEM
The listed detector is currently open
7

Direct Device Bypass
Activating Duress Signals
ENGLISH
1. Keypad (XMA/WMB)
Press and hold the button until the keypad beeps
rapidly three times
The display will show for 10 seconds
Enter a user code for the system followed by
Use the arrow keys to nd the device you would like to
bypass and press
Repeat the steps above until all desired devices have been
set to be bypassed
Selected devices will be bypassed on the next
arming. If the system is not armed in the
next 24 hours the devices will return to
"Not Bypassed"
When arming with any number of devices set to be
bypassed the display will read
BADGE OR CODE
1. Keypad (XMA/WMB)
Note: Duress codes are automatically set by the system when a code is added.
For an audible Duress enter a 4-6 digit user code with 2 numbers
higher than the actual code
For a silent Duress enter a 4-6 digit user code with 1 number
higher than the actual code
Example 1:
User code is set to: 1234
Audible Duress: 1236
Silent Duress: 1235
Example 2:
User code is set to: 123456
Audible Duress: 123458
Silent Duress: 123457
8 9
Your local installer: www.eaglesecuritysolutions.co.uk

ENGLISH
Activating Duress Signals - Continued
2. Remote Control (RC)

 Audible Duress
 Press the button and hold for 4 seconds.
 The remote control will beep twice in conrmation and all sounders will begin
Note: A single low tone noties the command was not recieved at
the control panel.
Silent Duress
 Press the button and hold for 4 seconds.
 The remote control will beep twice in conrmation
Note: A single low tone noties the command was not recieved at
the control panel.
Managing Badges / Access Codes
1. Keypad (XMA/WMB)
Note: Badges and codes can only entered into the system by a Level 3 user code
Accessing Level 3 Programming (XMA/WMB)
The display will read
Press the until the display reads
Press and use the to move the level to 3
Press . Display will show
Enter a valid level 3 code followed by or present a level 3 badge
to the for 2 seconds.
The display will show
The system will automatically default back to ACCESS LEVEL 1
after 60 seconds of inactivity.
DATE/TIME
DISARMED LVL 1
ACCESS LEVEL 1
BADGE OR CODE
ACCESS LEVEL 3
9

Adding a Badge:
Present the Badge to the or BR Reader for 2 seconds
The reader will beep and the display will change to
Enter a name for the badge or leave it blank and press
Managing Badges / Access Codes - Continued
Adding Badges/Codes (XMA/WMB)
Note: Badges require WMB or BR badge reader learned into the system.
Perform 'Accessing Level 3 Programming' and verify you are in
Access Level 3
Press until the display reads
Press . Display will show
Press . Display will show
Adding a Code:
Enter a 4-6 digit user code and press
The display will show
Re-enter the 4-6 digit code and press
The display will show
Enter a name for the code or leave it blank and press
The code has now been entered into the system
ENTER A
BADGE / CODE
CONFIRM THE CODE
BADGES AND ACCESS
CODES
BADGE / CODE
NAME OF CODE
NAME OF BADGE
Note: When a code is created the system will automaticaly generate two sub-codes that can
be used as a silen and audible duress. This means that for every code you create you will not be
able to create another code withing +/- 2 digits.
Example: Code 1234 has been created. 1235, 1236, 1233, 1232 are no longer available
ENGLISH
10 11

Deleting a Badge:
Display shows
Press
The badge is now deleted from the system
Deleting a Code:
Display shows
Enter teh code you wish to delete and press
Display shows
Press
The code is now deleted from the system
Managing Badges / Access Codes - Continued
Deleting Badges/Codes (XMA/WMB)
Perform 'Accessing Level 3 Programming' and verify you are in
Access Level 3
Press the until the display reads
Press and use the to move to
Press . Display will show the rst badge or code that is learned
into the system
Use the to nd the badge or code you wish to delete
Press
REENTER THE CODE
BADGES AND ACCESS
CODES
DELETING BADGES /
ACCESS CODES
DELETING CODE
NAME OF CODE
DELETING BADGE
NAME OF BADGE
Exiting From Programming
1. Keypad (XMA/WMB)
From any menu in programming you have exit back to the main screen
Hold the for 5 seconds to retunr to the main display
11

NOTES
12

NOTES
12

NOTES
12
Your local installer: www.eaglesecuritysolutions.co.uk