Viega 8350.35 User manual

for the reception of a flush actuation via radio signal
Model Year built:
8350.35 from 06/2012
en_INT
Radio receiver
Instructions for Use

Radio receiver 2 from 10

Table of contents
1About these instructions for use 4
1.1 Target groups 4
1.2 Labelling of notes 4
1.3 About this translated version 5
2Product information 6
2.1 Intended use 6
2.1.1 Areas of use 6
2.2 Product description 6
2.2.1 Overview 6
2.2.2 Operating mode 6
2.2.3 Extensions 7
3Handling 8
3.1 Assembly 8
3.2 Commissioning 9
3.3 Disposal 10
Table of contents
Radio receiver 3 from 10

1 About these instructions for use
Trade mark rights exist for this document, further information can be
found at viega.com/legal .
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
nHeating and sanitary professionals and trained personnel
It is not permitted for individuals without the abovementioned training or
qualification to mount, install and, if required, service this product. This
restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
1.2 Labelling of notes
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns against possible life-threatening injury.
WARNING!
This symbol warns against possible serious injury.
CAUTION!
This symbol warns against possible injury.
NOTICE!
This symbol warns against possible damage to property.
Notes give you additional helpful tips.
About these instructions for use
Radio receiver 4 from 10

1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e. g. EN) and/or in Germany
(e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The pertinent national laws, stand-
ards, regulations and guidelines, as well as other technical guidelines,
have priority over German/European guidelines in this manual: The
information is not binding for other countries and territories and should,
as mentioned, be considered as support.
About these instructions for use
Radio receiver 5 from 10

2 Product information
2.1 Intended use
2.1.1 Areas of use
The radio receiver may only be used with the following Viega products:
Compatible WC flush plates:
nVisign for Public 5, model 8326.16
nVisign for Public 6, model 8326.15
nVisign for Care sensitive, model 8352.21
nVisign for More 100 sensitive, model 8352.11
nVisign for More 100 sensitive, model 8352.12
nVisign for More 103 sensitive, model 8355.11
nVisign for More 103 sensitive, model 8355.12
Compatible WC flush actuation:
nModel 8350.31
nModel 8350.32
nModel 8350.33
nModel 8350.34
2.2 Product description
2.2.1 Overview
3
2
1
Fig. 1: Radio receiver 8350.35
1 - programming button
2 - LED
3 - connection adapter
2.2.2 Operating mode
Signals to actuate the flush (e. g. on support hinged handles) sent by
HEWI radio transmitters can be received by the radio receiver.
Up to 32 receivers can be connected to a radio receiver.
Product information
Radio receiver 6 from 10

2.2.3 Extensions
Multiple sensors can be connected to a control at the same time using
the extension cable adapter model 8350.36. This is how e. g. a button
can be combined with the radio receiver.
Fig. 2: Extension cable adapter model
8350.36
Fig. 3: Connection diagram for radio and
cable sensors
Product information
Radio receiver 7 from 10

3 Handling
3.1 Assembly
Insert radio receiver into the bracket of the control.
Create plug connection from radio receiver to control.
Handling
Radio receiver 8 from 10

3.2 Commissioning
Press programming button briefly.
ðThe LED blinks once.
Press the flush button of the radio transmitter to be programmed
within 30 seconds.
In the case of dual volume radio transmitters, push one of the two
flush buttons.
ðThe LED blinks three times.
Repeat the process to program additional transmitters (maximum 32
per receiver).
Keep programming button pressed for approx. 8 seconds.
ðThe LED blinks twice.
Release programming button.
ðThe radio receiver's memory has been deleted.
Programming
Deleting memory
Handling
Radio receiver 9 from 10

3.3 Disposal
Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.
Handling
Radio receiver 10 from 10