ViewLight Inami L-0955-SD User manual

This time, Zoom LED portable operation microscope , Thank you for purchasing.
Please use properly on before using this manual well read, and you know how to use, etc..
And stop use if you can't follow the preparation and operation, please contact the dealer or our
company.
Table of contents
１． Safety warnings and cautions ･････････････････････････････････・・・････ ２
２．Names of parts, accessories and product overview and structure ･･････････ ３
３．Assembly instructions ･･･････････････････････････････････・・・･･････ ５
４．Instructions ････････････････････････････・・・・･･････････････････････ ７
５．Replacing the cleaning of medical equipment, consumables and storage ･････ １０
６．Maintenance ･･････････････････････････････・･･････････････････・・･････ １１
７．Troubleshooting ･･････････････････････････････････････････････････・・・・･･ １３
８．Spec ･･･････････････････････････････････････････････････・・・・･･･････ １５
９．After-sale service ････････････････････････････････････････････・・・・･･････ １５
・Please note that there is a regarding the contents of this manual, for the improvement of future change
without notice to you.
・Measures about the contents of this manual has been created, but any errors, please contact your dealer if you
have concerns, such as omissions.
・Will be replaced if unclear, missing. Please contact the dealer.

１． Safety warnings and cautions
Before using this safety warnings and precautions well read on the right please.
Keep important this instruction manual so that you can view at any time.
Because the precautions listed in this section are provided to serious safety always keep.
The symbols and their meanings in the following.
Danger
Indicates a hazard that can cause deaths, or imminent danger of injury.
Warning
Indicates content or applied incorrectly, creates the possibility of death or injury
is expected.
Attention
Indicates the possibility of injury to people or material damage of injury.
However, it may lead to serious consequences in some situations.
Pertaining to the houses and household goods and material damage, damage.
Alerts
・During the replacement parts please be sure main power switch to the OFF (O).
Electric shock while energizing to work.
・Body 10 times over not tilt please.
Beside the body and damage the injured, houses, and other instruments.
Attention
・Please attach ground wire.Upon failure or short circuit of an electric shock.
・Unplug the power supply plug ( Plug ) Hands must be dry, with advanced plug and unplug
(Pointing ) Please. An electric shock may ignite or short.
・Please do not use firmness the power supply cord or plug, or corrupt.An electric shock may ignite
or short.
・Hurt power cord forcibly bend, pull, twist, bind, place heavy items, please do not
conductive.Power cord is damaged, can cause fire or electric shock.
・Power cord no dirt, dust, oil, so please, clean at all times.Terminals may be dirty and cause fire or
malfunction.
・Outside of clinic hours, plug-ins, unplug from the wall outlet.On the cause of the short circuit and
fire.
・Please do not use other bulbs, fuse, electrical components.Risk of fire due to heat.
・Do not use lenses other than specified.Be able to observe the proper focus and magnification.
・When placing your body between table and in table clocks-lamp system handles firmly.On the
stand next to the slide, falling damage the injured, houses, and other instruments.
・And absolutely never disassemble the body.On the cause of the failure, or fire.
２． Name parts and accessories with the product overview and structure

１） Product overview
・Zoom LED portable operation microscope Is lightweight, compact, and handling ease has been designed
for the purpose.
・You can set the position to facilitate adoption of the spring arm.
・By 45 degrees tilting mirror to get rid of ENT , Can be used, such as orthopaedic surgery.
・Microscope head and compact design for observation, and made it possible to observe for a
long time.
・You can choose from two types of models, depending on the intended use.
Ｌ－０９５５ＳＤ
Table clamp system
Ｌ－０９５５ＳＤ + Ｋ－１４２２
Base stand system

２）付属品
２） 各部の名称
1 dust cover 1
2 Objective lens cap 1
3 eyepiece cap 2
4 Fuse 2
5 Mouth opening rubber 2
6 Disinfection cap 7
7 Power cord 1
8 Charger 1
1 12.5 Eyepiece lens
2 PD adjustment knob
3 Microscope removal screw
4 Zoom magnification control knob
5 objective lens
6 Filter switch
7 Microscope head rotation knob
8 Second arm balance knob
9 Second arm rotation control knob
10 Power supply unit
11 Illumination control knob
12 First arm rotation control knob
13 Microscope head adjustment knob
14 Microscope head angle adjuster
15 First arm base
16 First arm
17 second arm
18 Zoom microscope head
19 Focusing knob
20 Delivery Ali
21 Table clamp (SD type)
22 Stand
23 Battery unit
24 Battery

３． Assembly instructions
１）installation
(1) Installation conditions
·Please place it in a place not subject to water.
·Please place it in places where there is no fear of adverse effect due to air including
atmospheric pressure, temperature, humidity, ventilation, sunlight, dust, salt, ion content
etc.
·Please pay attention to stable conditions such as inclination, vibration and impact.
·Do not install in place of chemical storage or gas generation.
(2) Assembly method
·When installing, please adhere strictly to ensure that the environmental conditions at the
time of use are the following environmental conditions.
２）Assembly method
（１）for the first arm-based
①
clamp
（L-0940SD）
Stabilize the base with the handle firmly.
(Maximum table thickness:
70
mm)
②base（Ｋ-1422）
Pillar and base please tighten at the hexagon
bolt with a hole (4 screws).
（２）first arm
First arm installed Teflon washer and insert
into base.
The arm slowly insert vertically.
（３）second arm
No. 2 arm installed Teflon washer and insert
first arm.
The arm slowly insert vertically.
Environmental conditions
Temperature ＋１０℃～＋３５℃
Relative humidity ３０％～７５％
No.1 arm
No.2 arm
Teflon washer
No.1 arm
Teflon washer
base
pillar

（４）eyepiece with Prism box installation
Scale conversion box installed eyepiece Prism box,
clamp screws.
（５）installation of the power unit
Power supply unit to the Teflon washer Mounting
the chapter 1
Perpendicular to the arm slowly insert.
The fixed position, tighten the hex screws under the
one-arm. Screw the click in place. Please make
sure the swivel transformer.
（６）connect the power cable
Plug the power cable into the mirror cylinder of the
fix.
Plug the power cable into the power supply Jack,
please fix.
Please insert the battery cable into the power
supply unit and fix it.
Batter cable
power cable
eyepiece
Clamp screws
Scale conbersion
box No.1 arm
Teflon washer
Supply unit

４． Instructions
（How do）
（１）power switch
If you turn on the unit, press the power switch |.
（２）coaxial lighting brightness adjustment knob
Darkens the light mirror tunnel side coaxial lighting
brightness adjustment knob turns to the right and turn left.
（３）フィルター
Please select a filter using the filter switch knob on the
tube side mirror.
In each filter set you want.
Type Blue, retinal protection filters,
Color temperature change filter
（４）vertical fine adjustment knob
You can refine your focal length by
manipulating the vertical fine adjustment knob
and loosen the clamping lever. (Fine amount: 30
mm)
Vertical fine
adjustment knob rise
fall
Clamping lever
Fine amount
30mm
Filter switch knob
coaxial lighting brightness adjustment knob
Power switch

（５）turn locking knob
Tightening the lock knob rotation on postgraduate
offered by the rotation, fixed.
（６）diopter adjustment
Rotate the eyepiece and adjust the scale to a diopter
measured by.
（７）adjustment
ＰＤcontrol knob to rotate, and adjust the scale to a
measured by eyes wide.
（Microscopic head angle adjuster）
Microscope head is the microscope head tilt locking knob loose, 0 °~ 90 °up to adjust to any position you
can.
（８）Battery
Insert the battery cable into the power supply unit and install the battery in the battery unit, you can operate
it with the battery.
When power is supplied from the AC cable, operation with the battery can not be performed. When operating
with a battery, please stop supplying power from the AC cable.
Battery cable
AC cable
Head tilt locking knob
eyepiece
PD control knob
Tightening the lock knob

（９）Battery charging
Insert the charger's power plug into the indoor outlet (100 to 240 VAC) and install the battery.
The red lamp lights up while charging. The green lamp will light up when it is fully charged.
*Lamp lighting status indicates the following meaning.
Yellow Lit：Energized Red Lit：Charging Green Blinking：Practical charging completed
Green lighting：Charging completed yellow flashing：Charging standby Red flashing：Not charging
After charging, unplug the power plug and remove the battery.