ViewSonic CDP4237-L User manual

CDP4237-L
CDP4737-L
CDP5537-L
User Guide
Model No. VS14673/VS14674/VS14675
IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://
ZZZYLHZVRQLFFRPLQ(QJOLVKRULQVSHFL¿FODQJXDJHVXVLQJWKH5HJLRQDOVHOHFWLRQ
box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”

i
Compliance Information
For U.S.A.
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
5HRULHQWRUUHORFDWHWKHUHFHLYLQJDQWHQQD
,QFUHDVHWKHVHSDUDWLRQEHWZHHQWKHHTXLSPHQWDQGUHFHLYHU
&RQQHFWWKHHTXLSPHQWLQWRDQRXWOHWRQDFLUFXLWGLIIHUHQWIURPWKDWWRZKLFKWKHUHFHLYHULVFRQQHFWHG
&RQVXOWWKHGHDOHURUDQH[SHULHQFHGUDGLR79WHFKQLFLDQIRUKHOS
:DUQLQJ<RXDUHFDXWLRQHGWKDWFKDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHGE\WKHSDUW\UHVSRQVLEOH
for compliance could void your authority to operate the equipment.
For Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CE Conformity for European Countries
The device complies with the EMC Directive 2004/108/EC and Low Voltage Directive 2006/95/
EC.
Following information is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical and Electronic
Equipment Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment as unsorted municipal
waste, but use the return and collection systems according to local law.

ii
Important Safety Instructions
1. Read these instructions completely before using the equipment.
2. Keep these instructions in a safe place.
3. Heed all warnings.
4. Follow all instructions.
5. 'RQRWXVHWKLVHTXLSPHQWQHDUZDWHU:DUQLQJ7RUHGXFHWKHULVNRI¿UHRUHOHFWULFVKRFNGRQRWH[SRVH
this apparatus to rain or moisture.
6. Do not block any ventilation openings. Install the equipment in accordance with the manufacturer’s
instructions.
7. Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including
DPSOL¿HUVWKDWSURGXFHKHDW
8. Do not attempt to circumvent the safety provisions of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two blades and a third
JURXQGLQJSURQJ7KHZLGHEODGHDQGWKHWKLUGSURQJDUHSURYLGHGIRU\RXUVDIHW\,IWKHSOXJGRHVQRW¿W
into your outlet, consult an electrician for replacement of the outlet.
9. Protect the power cord from being tread upon or pinched, particularly at the plug, and the point where
if emerges from the equipment. Be sure that the power outlet is located near the equipment so that it is
easily accessible.
10. 2QO\XVHDWWDFKPHQWVDFFHVVRULHVVSHFL¿HGE\WKHPDQXIDFWXUHU
11. 8VHRQO\ZLWKWKHFDUWVWDQGWULSRGEUDFNHWRUWDEOHVSHFL¿HGE\WKHPDQXIDFWXUHURUVROG
with the equipment. When a cart is used, use caution when moving the cart/equipment
combination to avoid injury from tipping over.
12. Unplug this equipment when it will be unused for long periods of time.
13. 5HIHUDOOVHUYLFLQJWRTXDOL¿HGVHUYLFHSHUVRQQHO6HUYLFHLVUHTXLUHGZKHQWKHXQLWKDVEHHQGDPDJHG
in any way, such as: if the power-supply cord or plug is damaged, if liquid is spilled onto or objects fall
into the unit, if the unit is exposed to rain or moisture, or if the unit does not operate normally or has
been dropped.

iii
Declaration of RoHS Compliance
This product has been designed and manufactured in compliance with Directive 2002/95/EC of the European
Parliament and the Council on restriction of the use of certain hazardous substances in electrical and
electronic equipment (RoHS Directive) and is deemed to comply with the maximum concentration values
issued by the European Technical Adaptation Committee (TAC) as shown below:
Substance Proposed Maximum Concentration Actual Concentration
Lead (Pb) 0,1% < 0,1%
Mercury (Hg) 0,1% < 0,1%
Cadmium (Cd) 0,01% < 0,01%
Hexavalent Chromium (Cr6+) 0,1% < 0,1%
Polybrominated biphenyls (PBB) 0,1% < 0,1%
Polybrominated diphenyl ethers (PBDE) 0,1% < 0,1%
Certain components of products as stated above are exempted under the Annex of the RoHS Directives as
noted below:
Examples of exempted components are:
 0HUFXU\LQFRPSDFWÀXRUHVFHQWODPSVQRWH[FHHGLQJPJSHUODPSDQGLQRWKHUODPSVQRWVSHFL¿FDOO\
mentioned in the Annex of RoHS Directive.
 /HDGLQJODVVRIFDWKRGHUD\WXEHVHOHFWURQLFFRPSRQHQWVÀXRUHVFHQWWXEHVDQGHOHFWURQLFFHUDPLF
parts (e.g. piezoelectronic devices).
3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).
4. Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium containing up
to 0.4% lead by weight and as a cooper alloy containing up to 4% lead by weight.

1
Copyright Information
Copyright © ViewSonic®Corporation, 2012. All rights reserved.
ViewSonic®, the three birds logo, OnView®, ViewMatch™, and ViewMeter®are registered trademarks of
ViewSonic®Corporation.
ENERGY STAR®is a registered trademark of the U.S. Environmental Protection Agency (EPA).
As an ENERGY STAR®partner, ViewSonic Corporation has determined that this product meetsthe ENERGY
STAR®JXLGHOLQHVIRUHQHUJ\HI¿FLHQF\
Disclaimer: ViewSonic®Corporation shall not be liable for technical or editorial errors or omissions contained
herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance
or use of this product.
In the interest of continuing product improvement, ViewSonic®Corporation reserves the right to change
SURGXFWVSHFL¿FDWLRQVZLWKRXWQRWLFH,QIRUPDWLRQLQWKLVGRFXPHQWPD\FKDQJHZLWKRXWQRWLFH
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without
prior written permission from ViewSonic®Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it becomes available, please
register your product on the Internet at: www.viewsonic.com.
For Your Records
Product Name:
Model Number:
Document Number:
Serial Number:
Purchase Date:
CDP4237-L/CDP4737-L/CDP5537-L
ViewSonic LCD Commercial Display
VS14673/VS14674/VS14675
CDP4237-L_4737-L_5537-L_UG_ENG Rev. 1A 02-03-12
Product disposal at end of product life
ViewSonic respects the environment and is committed to working and living green. Thank you for being part
of Smarter, Greener Computing. Please visit ViewSonic website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/kbase/article.php?id=639
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

2
CONTENTS
4LICENSES
5ASSEMBLING AND
PREPARING
5 Accessories
6 Optional Accessories
7 Parts and buttons
8 Using the Mounting Cable Tie
8 Connecting the Speakers
9 Connecting the stand
9 Using the Kensington security system
10 Portrait Layout
11 Mounting on a wall
12 REMOTE CONTROL
14 USING THE MONITOR
14 Connecting to a PC
15 - RGB connection
15 - DVI-D connection
16 - HDMI connection
16 - Display Port connection
17 Adjusting the screen
17 - Selecting an image mode
17 - Customizing image options
18 - Customizing PC display options
18 Adjusting the sound
18 - Selecting an sound mode
19 - Customizing sound options
19 Using additional options
19 - Adjusting aspect ratio
21 - Using the input list
22 ENTERTAINMENT
22 - Connecting to a wired network
23 - Network Status
24 - Connecting USB storage devices
25 - Browsing files
26 - Viewing movies
30 - Viewing photos
33 - Listening to music
36 - DivX® VOD Guide
37 - Using PIP/PBP
39 CUSTOMIZING SETTINGS
39 Accessing main menus
40 - PICTURE settings
43 - AUDIO settings
44 - TIME settings
45 - OPTION settings
50 - NETWORK settings
51 MAKING CONNECTIONS
52 Connecting to a HD receiver, DVD,
Camcorder, Camera, Gaming Device or
VCR player
52 - HDMI connection
52 - Component connection
53 - AV(CVBS) connection
53 Connecting to a USB
54 Connecting to the LAN
54 - LAN connection
55 Daisy Chain Monitors

3
56 TROUBLESHOOTING
59 SPECIFICATIONS
67 IR CODES
68 CONTROLLING THE MULTIPLE
PRODUCT
68 Connecting the cable
68 RS-232C Configurations
68 Communication Parameter

4
LICENSES
Supported licenses may differ by model. For more information of the licenses, visit www.ViewSonic.com.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks
or registered trademarks of HDMI Licensing LLC.
ABOUT DIVX VIDEO: DivX is a digital video format created by DivX, LLC, a
subsidiary of Rovi Corporation. This is an official DivX Certified device that
plays DivX video. Visit divx.com for more information and software tools to
convert your files into DivX videos.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified device must be registered in order to play purchased DivX Video-
on-Demand (VOD) movies. To obtain your registration code, locate the
DivX VOD section in your device setup menu. Go to vod.divx.com for more
information on how to complete your registration.
DivX Certified to play DivX video up to HD 1080p, including premium
content.
DivX , DivX Certified and associated logos are trademarks of Rovi
Corporation or its subsidiaries and are used under license.
Covered by one or more of the following U.S. patents: 7,295,673; 7,460,668;
7,515,710; 7,519,274
Manufactured under license from Dolby Laboratories. “Dolby” and the
double-D symbol are trademarks of Dolby Laboratories.

5
ASSEMBLING AND PREPARING
Accessories
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual product
and accessories.
y Do not use any pirated items to ensure the safety and product life span.
y Any damages or injuries by using pirated items are not covered by the warranty.
y The accessories supplied with your product may vary depending on the model.
y Product specifications or contents in this manual may be changed without prior notice due to upgrade
of product functions.
Remote control and Batteries Power Cord
CD (Owner's Manual)
/ Card
D-sub 15 pin signal cable Mounting Cable Tie
(Provided for CDP4237-L and
CDP4737-L models only)
CAUTION
NOTE
P
A
G
E
INPUT
ENERGY
SAVING
MARK
ARC
ON
OFF
X
. , !
Y
ABC
Z
DEF
[
GHI
\
JKL
]
MNO
^
PQRS
_
TUV
`
1/a/A
W
- * #
WXYZ
CLEAR
MONITOR
PSM
AUTO
MUTE
BRIGHT
NESS
MENU
POWER
OK
ID
BACK TILE
ON OFF
EXIT

6
Optional Accessories
Without prior notice, optional accessories are subject to change to improve the performance of the product,
and new accessories may be added. The illustrations in this manual may differ from the actual product and
accessories.
y Cable holder/Cable tie may not be available in some areas or for some models.
y Optional accessories are not included for all models.
Stand
Screws
: Diameter 4.0 mm x Pitch 0.7 mm x
Length 10mm(Included Spring Washer)
Cable holder
/Cable Tie
Screws
Diameter 4.0 mm x Pitch 0.7 mm x
Length 8 mm(Included Spring Washer)
Speaker
NOTE
Stand kit (STND-019) Speaker kit (SPK-012)

7
y You can set the Power indicator to on or off by selecting OPTION in the main menu.
Parts and buttons
Screen Marks Description
INPUT Changes the input source.
MENU Accesses the main menus, or saves your input and exits the menus.
Adjust the up and down.
Adjusts the volume level.
AUTO/SET Displays the current signal and mode.
Press this button to adjust the screen automatically (available only in RGB mode)
/I Turns the power on or off.
IR Receiver This is where the unit receives signals from the remote control.
Power Indicator This Indicator lights up blue when the display operates normally(on mode). If the display
In sleep mode (In Power Saving mode), this indicator color changes to amber.
Connection panel
Screen Buttons
Screen Marks
IR Receiver /
Power Indicator
yLighting On: Turned on
yLighting Off: Turned off
NOTE
MEZ63829306(REV00)

8
Connecting the Speakers
- Only on some models.
1Connect an input signal cable to use before
installing the speakers.
3After installing your speakers, use holders and
cable ties to organize the speaker cables.
2Mount the speaker by using a screw as shown
in the following. Then connect the speaker
cable.
Using the Mounting Cable
Tie
- Applicable only to CDP4237-L and CDP4737-L
models.
First, connect the input signal cable to be used.
Insert the cable tie into the bottom hole on the
back as shown in the figure to organize cables.
y The Mounting cable tie is provided for
CDP4237-L and CDP4737-L models only.
NOTE

9
2Use the screws to secure the stand on the rear
side of the product as shown in the diagram.
Connecting the stand
- Only on some models.
1Place a soft cloth on the table and put the
product with the screen facing downward.
Connect the stand as shown in the following
picture.
Using the Kensington
security system
The Kensington security system connector is
located at the back of the Monitor. For more
information of installation and using, refer to the
manual supplied with the Kensington security
system or visit
http://www.kensington.com .
Connect the Kensington security system cable
between the Monitor and a table.
y The Kensington security system is optional.
You can obtain additional accessories from
most electronics stores.
NOTE

10
Portrait Layout
- Only on some models.
When installing in a Portrait Layout, rotate the
monitor clockwise 90 degrees (when facing the
screen).

11
Mounting on a wall
For proper ventilation, allow a clearance of 10
cm on each side and from the wall. Detailed
installation instructions are available from your
dealer, see the optional Tilt Wall Mounting Bracket
Installation and Setup Guide.
10 cm
10 cm
10 cm
10 cm 10 cm
If you intend to mount the Monitor to a wall, attach
Wall mounting interface (optional parts) to the back
of the set.
When you install the Monitor using the wall
mounting interface (optional parts), attach it
carefully so it will not fall.
1Please, Use the screw and wall mount interface
in accordance with VESA Standards.
2If you use screw longer than standard, the
monitor might be damaged internally.
3If you use improper screw, the product might
be damaged and drop from mounted position.
In this case, ViewSonic Electronics is not
responsible for it.
4VESA compatible.
5Please use VESA standard as below.
y 785mm(31 inch) or greater
* Fastening screw: Diameter 6.0 mm x Pitch 1.0
mm x Length 10 mm
y Disconnect the power before installing or
moving the monitor. Otherwise electric shock
may occur.
y If you install the Monitor on a ceiling or
slanted wall, it may fall and result in severe
injury. Use an authorized ViewSonic wall
mount and contact the local dealer or
qualified personnel.
y Do not over tighten the screws as this may
cause damage to the Monitor and void your
warranty.
y Use screws and wall mounts that meet the
VESA standard. Any damages or injuries by
misuse or using an improper accessory are
not covered by the warranty.
y Use screws that are listed on the VESA
standard screw specifications.
y The wall mount kit includes an installation
manual and necessary parts.
y The wall mount bracket is optional. You can
obtain additional accessories from your local
dealer.
y The length of screws may differ depending
on the wall mount. Be sure to use the proper
length.
y For more information, refer to the instructions
supplied with the wall mount.
CAUTION
NOTE

12
REMOTE CONTROL
P
A
G
E
INPUT
ENERGY
SAVING
MARK
ARC
ON
OFF
X
. , !
Y
ABC
Z
DEF
[
GHI
\
JKL
]
MNO
^
PQRS
_
TUV
`
1/a/A
W
- * #
WXYZ
CLEAR
S.MENU
MONITOR
PSM
AUTO
MUTE
BRIGHT
NESS
MENU
POWER
/ I (POWER)
Turns the Monitor on or off.
MONITOR ON / OFF
Turn off the monitor and then
turn it back on.
1/a/A Button
This button selection is not
applicable.
ENERGY SAVING
Adjusts the brightness of
the screen to reduce energy
consumption.
INPUT
Selects the input mode.
Number and Alphabet buttons
Enters numbers.
The alphabet selection is not
applicable.
CLEAR
This button selection is not
applicable.
PSM
Selects the Picture Status
Mode.
MUTE
Mutes all sounds.
ARC
Selects the Aspect Ratio
Mode.
Volume Up / Down
Adjusts the volume level.
BRIGHTNESS Key
Adjust the brightness by
pressing the Up and Down
buttons on the remote control.
In USB mode, the OSD menu
has the Page function to move
to the next file list.
The descriptions in this manual are based on the buttons of the remote control. Please read this manual
carefully and use the Monitor correctly.
To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching and ends to the
label inside the compartment, and close the battery cover.
To remove the batteries, perform the installation actions in reverse.
y Do not mix old and new batteries, as this
may damage the remote control.
y Make sure to point the remote control at the
remote control sensor on the Monitor.
CAUTION

13
E
OK
AUTO
MUTE
NESS
MENU
ID
BACK TILE
ON OFF
EXIT
EXIT
Clears all on-screen displays
and returns to Monitor
viewing from any menu.
TILE
Selects the TILE Mode.
MENU (See p.39)
Accesses the main menus
or saves your input and exit
menus.
Navigation buttons
Scrolls through menus or
options.
OK
Selects menus or options and
confirms your input.
BACK
Allows the user to move back
one step.
USB Menu control buttons
Controls media playback.
ID ON/OFF
When more than one monitor
is present in the same room,
this allows you to control them
individually.
AUTO
Automatically adjusts picture
position and minimizes image
instability.(RGB input only)

14
USING THE MONITOR
Connecting to a PC
Your Monitor supports the Plug & Play* feature.
* Plug & Play: This is the function that allows a PC
to use the monitor without installing a driver.
NOTE
y Connect the signal
input cable and tighten
it by turning the screws
clockwise.
y Do not press the
screen with your finger for a long time as
this may result in temporary distortion on the
screen.
y Avoid displaying a fixed image on the screen
for a long period of time to prevent image
burn. Use a screensaver if possible.
y It is recommended to use the Monitor with
the HDMI connection for the best image
quality.
y Use a shielded signal interface cable, such
as D-sub 15 pin signal cable and DVI cable,
with a ferrite core to maintain standard
compliance for the product.
y If you turn the Monitor on when the set
becomes cold, the screen may flicker. This
is normal.
y Some red, green, or blue spots may appear
on the screen. This is normal.
CAUTION

15
DVI-D connection
Transmits the digital video signal from your PC to
the Monitor. Connect the PC and the Monitor
set with the DVI cable as shown the following
illustrations.
Select DVI-D input source on the monitor.
RGB OUT (PC) AUDIO OUT
RGB connection
Transmits the analog video signal from your PC to
the Monitor. Connect the PC and the Monitor
set with the 15 pin signal cable as shown the
following illustrations.
Select RGB input source on the monitor.
y Use the standard Macintosh
adapter since an incompatible
adapter is available in the
market. (Different signaling
system)
y Apple computers may require an adapter to
connect to this monitor. Call or visit their web
site for more information.
NOTE
AUDIO OUT
DVI OUT
Macintosh Adapter
(not included)
(not included)
(not included)
(not included)

16
HDMI connection
Transmits the digital video and audio signals from
your PC to the Monitor. Connect the PC and the
Monitor with the HDMI cable as shown in the
following illustrations.
Select HDMI input source.
Display Port connection
Transmits the digital video and audio signals from
your PC to the Monitor. Connect the PC and the
Monitor with the Display Port cable as shown in
the following illustrations.
Select Display Port input source.
y Use a High Speed HDMI™ Cable.
y Please check the PC environment if you
cannot hear the sound in HDMI mode. Some
PCs require you to manually change the
default audio output to HDMI.
y If you want to use HDMI PC mode, you must
set PC/DTV to PC mode.
y When HDMI PC is used, a compatiblity
problem might occur.
NOTE
HDMI
DP OUT
(not included)
(not included)