ViewSonic PT775 - 17" CRT Display User manual

PT775 Color Monitor
with Plug and Play
User’sGuide
17" (16.0"Viewable Diagonal)
PT775-3

ViewSonicPT775
1
For your records
The serial number of this product is on the back of the monitor.Write the serial
number in the space below and keep this guide as a permanent record of your
purchase to aid in identification in the event of theft or loss.
Model Name: ViewSonic PT775
ModelNumber: VCDTS21427-3
Serial Number: ______________________
PurchaseDate: ______________________
Copyright © ViewSonic®Corporation, 1998. All rights reserved.
Macintosh is a registered trademarks of Apple Computer, Inc.
Windows is a registered trademark of Microsoft Corporation.
ViewSonic, the three birds logo, OnView,ARAG, SonicTron, ViewMatch, andViewMeter are
registered trademarks of ViewSonic Corporation.
VESA is a registered trademark of theVideo Electronics Standards Association (VESA). DPMS is a
trademark ofVESA.
ENERGY STAR is a registered trademark of the U.S. Environmental ProtectionAgency (EPA).
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions
contained herein; nor for incidental or consequential damages resulting from furnishing this
material, or the performance or use of this product.
In the interest of continuing product improvement,ViewSonic Corporation reserves the right to
change product specifications without notice. Information in this document may change without
notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose
without prior written permission from ViewSonic Corporation.
Register your monitor atwww.viewsonic.com.It’s fast and easy, and will simplify your future support needs.
Electronic Warranty Registration
Power Cord Safety Guidelines
Caution : Use a power cable that is properly grounded. Always use the AC cords listed
below for each area : USA...........................UL
Canada......................CSA
Germany....................VDE
Switzerland................SEV
Britain .........................BASEC/BS
Japan.........................Electric Appliance Control Act
In other areas, use AC cord which meets local safety standards.
As an ENERGY STAR®partner,ViewSonic Corp. has determinded that this product meets the
ENERGY STAR®guidelines for energy efficiency.

ViewSonicPT775
2
IMPORTANT NOTICE CONCERNING POWER CORD SELECTION
The power cord for this unit has been packed separately and has been selected according to
the country of destination and must be used to prevent electric shock.Use the following
guidelines if it is necessary to replace the original cord set.
The female receptacle of the cord set must meet CEE-22 requirements and will look like
Figure1 below:
For the United States and Canada
In the United States and Canada the male plug is a NEMA5-15 style (Figure 2) UL Listed
and CSA Labelled.For units which are mounted on a desk or table, type SVT or SJT cord
sets may be used.For units which sit on the floor, only SJT type cord sets may be used.The
cord set must be selected according to the current rating for your unit.Please consultTable A
below for the selection criteria for power cords used in the United States and Canada.
For European Countries
In Europe you must use a cord set which is appropriate for the receptacles in your country.
The cord set is HAR-Certified, and a special mark that will appear on the outer sheath, or on
theinsulation of one of theinner conductors.
If you have any questions concerning which proper power cord to use, please consult with
thedealer from whom youpurchased yourmonitor.
Power Cord Safety Guidelines (continued)
AC PLUG CORD PRECAUTIIONS FORTHE UNITED KINGDOM
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET THEN THE
PLUG SHOULD BE CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS
INSERTED INTO AN APPROPRIATE SOCKET.
If a new plug is to be fitted, please observe the wiring code as shown below.
If in any doubt, please consult a qualified electrician.
WARNING: THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
Green-and-Yellow: Earth
Blue: Neutral
Brown: Live
If the coloured wires of the mains lead of this appliance do not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the
plug which is marked by the letter E or by the Earth symbol or coloured GREEN or GREEN-
AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal in the plug which is
marked with the letter N or coloured BLACK.The wire which is coloured BROWN must be
connected to the terminal in the plug which is marked with the letter L or coloured RED.
Figure 1
Figure 2
Table A
CordType Size of Conductors In Cord Maximum Current Rating of Unit
SJT 18AWG 10Amps
16AWG 12Amps
14AWG 12Amps
SVT 18AWG 10Amps
17AWG 12Amps

ViewSonicPT775
3
FCC Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential
installation.This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCCWarning:
To assure continued FCC compliance, the user must use the grounded power supply cord
and the provided shielded video interface cable with bonded ferrite cores. If BNC cable is
going to be used, use only shielded BNC(5) cable. Also, any unauthorized changes or
modifications not express ly approved by the party responsible for compliance could void
the user's authority to operate this device.
Power Supply Cord USA
For units with 100 - 120V input voltage in the USA, use the following :
UL Listed and CSA Certified Type SVT or SJT No.18/3 AWG rated 125Vac 7A min.
One end terminated in a molded on parallel blade, grounding attachment cap or hooded attachment cap
(15A, 125V configuration), other end terminated in a mold-on appliance coupler.
Notice for Germany
The X-rays generated in this unit are shielded sufficiently. High voltage: Max. 29 kV. For ergonomic reasons, we
recommend that you do not display blue characters on a dark background. Doing so may produce insufficient
contrast that could lead to eye strain.
Notice for Japan
This equipment falls under the class B information Technology Equipment based on the standard established by the
self-imposed Control Council for Radio interference through information-processing Equipment (VCCI).This
equipment is designed to be used in a household environment, However, if it is used near radio and television
receiver units, radio disturbances can occur. Use this equipment appropriately according to the instruction manual.
Required item Relative to StandardValue Relative to those Exceeding StandardValue Remarks
EMI* # 1 # 4
ESD* # 2 # 3
RADIATED RF* # 1 # 3
TRANSIENT F/B* # 1 # 3
LINE HARMONICS # 1
# 1: Satisfies the standards with no problems in performance and reliability.
# 2: Effects may appear temporarily on the screen but there will be no problem in reliability.
# 3: There is fear of the product breaking down.
# 4: If a signal cable other than that specified is used, it may be the cause of electromagnetic wave interruption of
peripheral devices. To assure continued CE compliance the user must use the provided 1.8m shielded video
signal cable with bonded ferrite cores at both ends of the cable.
Handle correctly in accordance with the instruction manual.
*EMI : Electromagnetic Interference *ESD : Electrostatic Discharge *RF : Radio Frequency *F/B : Fast Burst
CE Conformity
The device complies with the requirements of the EEC directive 89/336/EEC as
amended by 92/31/EEC and 93/68/EEC Art.5 with regard to“Electromagnetic
compatibility”, and 73/23/EEC as amended by 93/68/EEC Art. 13 with regard to
“safety”.

4GettingStarted
ViewSonicPT775
CONTENTS
Getting Started
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Quick Installation* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operation
Front Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
OnView®Main Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Other Information
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cleaning the Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . back cover
*To meet your future needs, and to receive any additional product information as it becomes available,
please register your monitor's warranty on the Internet at: http://www.viewsonic.com.

5 ViewSonicPT775 GettingStarted
Getting Started
Congratulations on your purchase of a ViewSonic PT775 monitor.
Important! Save the original box and all packing material for future
shipping needs.
NOTE: This product was designed for operation in the magnetic fields of the
geographical hemisphere where purchased. Also, the word "Windows®" in
this user guide refers to the following Microsoft®operating systems:
Windows '95, Windows '95 OSR 2.1, and Windows '98.
Package Contents
•ViewSonic PT775 monitor
• Video cable (15 pin HD D-sub)
• Power cord
• USB (Universal Serial Bus) cable
• Macintosh®adapter
• Windows '95 installation file (VS*.inf)
on diskette or CD-ROM
• User’s guide
• For the best viewing conditions, sit at least 18" from the monitor.
• AVOID TOUCHING THE SCREEN WITH YOUR FINGERS. Oils
from the skin are difficult to remove.
• NEVER REMOVE THE REAR COVER. The monitor contains high-
voltage parts. You may suffer serious injury if you touch these parts.
• Avoid exposing the monitor to direct sunlight or another heat source.
The monitor should be facing away from direct sunlight to reduce glare.
• Choose a well ventilated area to position your monitor. Do not place
anything on the monitor that prevents adequate dissipation of heat.
• Ensure the area around the monitor is clean and free of moisture.
• Keep the monitor away from magnets, motors, transformers, speakers,
and televisions.
• Do not place heavy objects on the monitor, video cable, or power cord.
• If smoke, abnormal noise, or strange odor is present, immediately
switch the monitor off and call your dealer or ViewSonic®. It is
dangerous to continue using the monitor.
• Always handle your monitor with care when moving it.
Precautions

6GettingStarted
ViewSonicPT775
Quick Installation
1Write the serial number on the back of the monitor in the space
provided on page 1 labeled "For your records" and register your
monitor's warranty on the Internet at: http//:www.viewsonic.com.
2Read the Precautions section thoroughly (page 5) before installing the
monitor. Make sure the computer and the monitor are both turned off
before connecting any cables.
3a PC users: Attach the video cable to the Video Input port on the monitor
(see below), then connect the other end to your computer.
3b Macintosh®users:A Macintosh computer requires a Macintosh adapter
4Attach the power cord to the back of the monitor. Then plug the other
end of the power cord into the power source (wall socket).
5Turn the computer on. Then press the POWER button on the front of
the monitor ON. (The Power light turns green.)
6Adjust the user controls to suit your personal preference. See the
Operation section (page 7). If there are any problems, see the
Troubleshooting section (page 13).
Important: To set the screen resolution, see user's guide of your
computer's graphic card for instructions. For a list of Preset Timing
Modes and the pre-adjusted screen resolution for this monitor, see page 12.
Basic installation is complete! Enjoy your new monitor!
Power
cord
Video
cable
BNC video ports
D-sub video port
Note: BNC
does not
support
Plug & Play
USB INPUT
(Upstream
port -- to
computer)
USB OUTPUT
(4 Downstream
ports on side of
monitor)

7
ViewSonicPT775 Operation
Operation
The buttons on the Front Control Panel and the OnView®controls allow you
to adjust your ViewSonic PT775 monitor (see below).
Front Control Panel
1Press button [1] to display the
Main Menu.
2Press the [▼]or [▲]button to
highlight the option that you
want to adjust.
3Press button [2] to display the
highlighted control. See the
next few pages for individual
control screens.
Power
switch
Power
LED
• Scrolls up to highlight option
• Increases value of selected option
• Displays Contrast control screen
• Scrolls down to highlight option
• Decreases value of selected
option
• Displays Contrast control
screen.
• Selectsa highlighted option
• Shows another control screen
• Shows Input Select control
screen (page 10)
• Displays Main Menu
• Exits control screens
OnViewMain Menu, Part 1
4Press the [▼]or [▲]button to adjust
the selected option.
5Press button [1] to exit control
screens and the Main Menu, parts
1-3.
All OnView menus and screens
clear automatically approximately
20 seconds after a button is pressed.
All adjustments are saved.
c
SELECT: 2
MAIN MENU
[
1
]
CONTRAST/BRIGHTNESS
H.SIZE/POSITION
V.SIZE/POSITION
PINCUSHION/PIN BAL
TRAPEZOID/PARALLEL
HOURGLASS/HOOKING
EXIT: 1

8Operation
ViewSonicPT775
NOTE: Press [2] to toggle between all controls that appear on the Main
Menu in pairs (for example, Contrast/Brightness).
CONTRAST adjusts foreground white level of screen image.
Press [▼] or [▲] to adjust.
Shortcut: Before displaying the Main Menu, press [▼] or [▲] to
display the Contrast control screen.
BRIGHTNESS adjusts background black level of screen image.
Press [▼] or [▲] to adjust.
H. SIZE (Horizontal Size) adjusts width of screen image.
[▼] decreases width, [▲] increases width.
H. POSITION (Horizontal Position) moves screen image left or right.
[▼] moves screen image left, [▲] moves screen image right.
V. SIZE (Vertical Size) adjusts height of screen image.
[▼] decreases height, [▲] increases height.
V. POSITION (Vertical Position) moves screen image up or down.
[▼] moves screen down, [▲] moves screen up.
PINCUSHION straightens vertical sides of screen image.
[▼] curves vertical edges inward, [▲] curves vertical edges outward.
PIN-BALANCE curves the screen's vertical edges to the left or right.
[▼] curves vertical edges to left, [▲] curves vertical edges to right.
TRAPEZOID makes vertical edges of screen image parallel.
[▼] narrows top and widens bottom, [▲] widens top and narrows bottom.
PARALLELOGRAM slants vertical edges of screen image to left or
right. [▼] slants vertical edges to left, [▲] slants vertical edges to right.
HOURGLASS smooths all curves (shaped like an archery bow) along
the sides of the screen image until they apppear straight.
[▼] or [▲] to adjust.
HOOKING smooths hook-shaped curves along the sides of the screen
image until they apppear straight.
[▼] or [▲] to adjust.
...continued
To exit the OnView®menu & save changes, press button [1].
OnViewMain Menu, Part 1, continued

9
ViewSonicPT775 Operation
OnViewMain Menu, Part 2
TILT rotates entire screen image.
[▼] rotates screen image counter-clockwise, [▲] rotates screen image
clockwise.
VIEWMETER®displays the frequency signal input (horizontal scan
and refresh rate) coming from the graphics card in your computer. See
your graphics card's user guide for more details. (fh = Horizontal
Frequency; fv = Vertical Frequency, or refresh rate.)
H. CONVERGENCE (Horizontal Convergence) adjusts vertical color
alignment. Use this control only if you see red or blue around the
vertical segments of black letters on a white background.
Press [▼] and [▲] to adjust the color alignment.
V. CONVERGENCE (Vertical Convergence) adjusts horizontal color
alignment. Use this control only if you see red or blue around the
horizontal segments of black letters on a white background.
Press [▼] and [▲] to adjust the color alignment.
H. FOCUS adjusts the sharpness of the screen image in the horizontal
direction.
Press [▼] and [▲] to adjust.
V. FOCUS adjusts the sharpness of the screen image in the vertical
direction.
Press [▼] and [▲] to adjust.
PURITY adjusts the color purity of the overall image.
Press [▼] and [▲] to adjust.
NOTE: First use DEGAUSS to reduce color unevenness (see page 11).
Then if one area is still darker than another area, use PURITY.
To exit the OnView®menu & save changes, press button [1].
MAIN MENU [2]
TILT
VIEWMETER
CONVERGENCE
FOCUS
PURITY
VIEWMATCH COLOR
EXIT: 1 SELECT:
2

10 Operation
ViewSonicPT775
Press [▼] or [▲] to select one of these
color controls.If USER COLOR is
selected, then press [2] to display the
USER COLOR control screen.
From theUSER COLOR Control Screen
press [2] to select Red, Green, or Blue,
then press [▼] or [▲] to adjust.
To exit the OnView®menu & save changes, press button [1].
USER COLOR Control Screen
OnViewMain Menu, Part 2, continued
OnViewMain Menu, Part 3
MAIN MENU [3]
INPUT SELECT
OSD POSITION
MOIRE
DEGAUSS
LANGUAGE
DATA RECALL
EXIT: 1 SELECT:
2
INPUT SELECT toggles between D-Sub and BNC video sources,
giving you the option of switching between two monitors (see page 6).
Press [▼] or [▲] to select one of these options.
Shortcut: While no menu or screen is visible on screen, press [2] to
display the Input Select screen.
H. OSD POSITION (Horizontal On Screen Display Position)
repositions menus and control screens horizontally.
Press [▼] to move OSD to left, [▲] move OSD to right.
V. OSD POSITION (Vertical On Screen Display Position) repositions
menus and control screens vertically.
Press [▼] to move OSD down, [▲] move OSD up.
SELECT:
2
1
EXIT:
VIEWMATCH COLOR
9300K
6500K
5500K
USER COLOR
1
EXIT:
RED
40
- +
GREEN
40
- +
BLUE
40
- +
2
SELECT COLOR:
VIEWMATCH®COLOR provides four color adjustment options:
three preset color temperatures and USER COLOR which allows you
to adjust the red, green, and blue individually. NOTE: The factory
setting for the monitor is 9300K, the color temperature most
frequently used in offices with fluorescent lights.

11
ViewSonicPT775 Operation
MOIRE reduces vertical interference patterns that appear as ripples,
waves, or unwanted background color textures.
Press [▼] and [▲] to minimize interference patterns.
NOTE: Interference patterns of this type are most noticeable when
viewing images having closely spaced lines or finely detailed
patterns.
DEGAUSS removes the build-up of magnetic fields that can cause
irregular colors to appear around the edges of screen images.
With DEGAUSS highlighted, press [2] twice.
Important: Do not degauss repeatedly. Doing so can be harmful to the
monitor. Wait at least 20 minutes before selecting this control again.
LANGUAGE allows you to choose from among four languages for
the OnViewMain Menu and control screens: English, French,
German, and Spanish.
Press [▼] or [▲] to select a language.
DATA RECALL returns all controls (except User Color) back to
factory settings for the video timing currently selected.
Press [2] to recall factory settings.
If you want to exit the DATA RECALL screen and do not want to
recall factory settings, press [1].
OnViewMain Menu, Part 3, continued
To exit the OnView®menu & save changes, press button [1].

12
ViewSonic PT775
OtherInformation
Specifications
CRT Type 17" (16.0" viewable) diagonal
0.25mm aperture-grille pitch, 90° deflection
Screen ARAG®coating (anti-reflective, anti-glare)TM = 38%
Input Signal Video RGB analog (0.7Vp-p, 75 ohms)
Sync H/V separate (TTL), composite, sync-on-green,
fh: 30-96 kHz, fv: 50-160 Hz
Maximum Refresh VESA®1600 x 1280 NI @ 72Hz Macintosh * 1600 x 1200 @ 77Hz
Rates** VESA 1600 x 1200 NI @ 77Hz Macintosh * 1152 x 870 @ 104Hz
VESA 1280 x 1024 NI @ 89Hz Macintosh * 1024 x 768 @ 117 Hz
VESA 1024 x 768 NI @ 117Hz Macintosh * 832 x 624 @ 142 Hz
VESA 800 x 600 NI @ 148Hz Macintosh * 640 x 480 @ 160 Hz
VESA 640 x 480 NI @ 160Hz
Power Voltage AC 90-264VAC 47-63 Hz
Input/Output Input Signal 15-pin mini D-sub, BNC (X5)
Connectors Power 3-pin plug (IEC320)
USB Input (Upstream) port (square),
Output (Downstream) ports (rectangular) (X4)
Display Area Default 310mm (H) x 232mm (V) (typical)
Full Scan 327mm (H) x 246mm (V) (depends on signal timing)
Operating Temperature 32°F to 104°F (0°C to 40°C)
Conditions Humidity 5% to 95% (no condensation)
Altitude To 10,000 feet
Storage Temperature -4°F to +140°F (-40°C to +60°C)
Conditions Humidity 5% to 95% (no condensation)
Altitude To 40,000 feet
Dimensions Physical 414mm (W) x 426mm (H) x 435mm (D)
(monitor) 16.3" (W) x 16.8"(H) x 17.1"(D)
Weight Net 20.5kg (45.3 lbs) (monitor only)
Regulations UL, CSA, FCC-B, DHHS,TUV/GS, MPR-II, DOC-B,
ENERGY STAR®,TCO'95, NORDIC, BCID, ISO 9241-3,
CE, CB
Power Saving On green < 140Watts
LED Modes Stand By orange < 15Watts
Suspend orange < 15Watts
Off blinkingorange < 8Watts
* A Macintosh computer requires a Macintosh adapter.To order a ViewSonic
®
Macintosh adapter, contact
Customer Support (see the back cover). NOTE:You will need to provide your monitor's serial number.
** Warning: Do not set the graphics card in your computer to exceed these maximum refresh rates.
Doing so may result in permanent damage to the monitor.
VGA 640 x 350 @ 70Hz
VESA 640 x 400 @ 70Hz
VGA 640 x 480 @ 60Hz
VESA 800 x 600 @ 75Hz
VESA 1024 x 768 @ 75Hz, 85Hz
VESA 1280 x 1024 @ 75Hz, 85Hz
Macintosh 832 x 624 @ 75Hz
Macintosh 1024 x 768 @ 75Hz
Macintosh 1152 x 870 @ 75Hz
Other Information
Preset Timing Modes(the monitor has been pre-adjusted toVESA 1024 x768 @ 75Hz )

13
ViewSonicPT775
OtherInformation
Troubleshooting
No power
• Make sure front Power button (or switch) is ON.
• Make sure A/C power cord is securely connected to back of monitor and to
a power outlet.
• Plug another electrical device (like a radio) into power outlet to verify that
outlet is supplying proper voltage.
Power on but no screen image
• Make sure video cable supplied with monitor is tightly secured to video
output port on back of computer. If other end of video cable is not attached
permanently to monitor, tightly secure it to monitor.
• Adjust brightness and contrast.
• Check this user's guide to see if an adapter is required for proper signal
continuity between graphics card and monitor.
Flickering
• Not enough power supplied. Connect monitor to different outlet. If using
surge protector, reduce number of devices plugged in.
• Check ViewMeter®to verify refresh Tw[2c-0.06sv21.1(lr)-14.6(wtcal dfequiency) is O5 3Hz o
chghtr Se iSpecifcalion
• Make sure fgw[2c-hics card ain y34.7(eourcomputer)carnusernotn-ntormlace mone tt

14
ViewSonic PT775
OtherInformation
Cleaning the Monitor
• MAKE SURE THE MONITOR IS TURNED OFF.
• NEVER SPRAY OR POUR ANY LIQUID DIRECTLY ONTO THE
SCREEN OR CASE.
To clean the screen
1Wipe the screen with a clean, soft, lint-free cloth. This removes dust
and other particles.
2If still not clean, apply a small amount of non-ammonia, non-alcohol
based glass cleaner onto a clean, soft, lint-free cloth, and wipe the
screen.
To clean the case
1Use a soft, dry cloth.
2If still not clean, apply a small amount of a non-ammonia, non-alcohol
based, mild non-abrasive detergent onto a clean, soft, lint-free cloth,
then wipe the surface.
DISCLAIMER
ViewSonic does not recommend the use of any ammonia or alcohol-based cleaners
on the monitor screen or case.Some chemical cleaners have been reported to
damage the screen and/or case of the monitor.ViewSonic will not be liable for
damage resulting from use of any ammonia or alcohol-based cleaners.

15
ViewSonicPT775
OtherInformation
LIMITED WARRANTY
VIEWSONIC PT775 MONITORS
What the warranty covers:
ViewSonic®warrants its products to be free from defects in material and workmanship during the
warranty period.If a product proves to be defective in material or workmanship during the warranty
period,ViewSonic will at its sole option repair or replace the product with a like product.Replacement
product or parts may include remanufactured or refurbished parts or components.
How long the warranty is effective:
ViewSonic
PT775 color monitors, including the display tubes, are warranted for three (3) years for all
parts and three (3) years for all labor from the date of the first consumer purchase.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, or failure to follow instructions supplied with the product.
b. Repair or attempted repair by anyone not authorized by ViewSonic.
c. Any damage of the product due to shipment.
d. Removal or installation of the product.
e. Causes external to the product, such as electric power fluctuations or failure.
f. Use of supplies or parts not meetingViewSonic’s specifications.
g. Normal wear and tear.
h. Any other cause which does not relate to a product defect.
3. Removal, installation, and set-up service charges.
How to get service:
1. For information on obtaining warranty service, callViewSonic. The customer support telephone
numbers are:U.S.and Canada1-800-688-6688; from outside the U.S.and Canada 909-869-
7976;from Europe44 (1293) 643-900; from Asian /Pacific Rim countries886 (2) 248-4072.
Internet E-Mail address:[email protected] orWorldWideWeb:http://www.viewsonic.com
2. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your
name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.
3. Take or ship the product prepaid in the original container to yourViewSonic dealer, anyViewSonic
service center orViewSonic.
4. For additional information or the name of the nearestViewSonic service center, contact your
ViewSonic dealer orViewSonic.
Limitation of implied warranties:
THERE ARE NOWARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYONDTHE
DESCRIPTION CONTAINED HEREIN INCLUDINGTHE IMPLIEDWARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Exclusion of damages:
VIEWSONIC’S LIABILITY IS LIMITEDTOTHE COST OF REPAIR OR REPLACEMENT OFTHE
PRODUCT. VIEWSONIC SHALL NOT BE LIABLE FOR:
1. DAMAGETO OTHER PROPERTY CAUSED BY ANY DEFECTS INTHE PRODUCT, DAMAGES
BASED UPON INCONVENIENCE, LOSS OF USE OFTHE PRODUCT, LOSS OFTIME, LOSS OF
PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCEWITH
BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS, EVEN IF ADVISED OFTHE
POSSIBILITY OF SUCH DAMAGES.
2. ANY OTHER DAMAGES,WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
3. ANY CLAIM AGAINSTTHE CUSTOMER BY ANY OTHER PARTY.
Effect of state law:
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state. Some states do not allow limitations on implied warranties and/or do not allow the
exclusion of incidental or consequential damages, so the above limitations and exclusions may not
apply to you.
Sales outside the U.S.A.:
ForViewSonic products sold outside of the U.S.A., contact your ViewSonic dealer for warranty
information and service. REV 2/4/98

16
ViewSonic PT775
OtherInformation
NOTES

ViewSonic®Corporation
381 Brea Canyon Road
Walnut, CA 91789
Tel [phone]
Tel [phone]
Fax [phone]
V803157753
For ViewSonic®Customer Support:
U.S. and Canada only
1-800-688-6688
From outside U.S. and Canada
909-869-7976
From Europe
+ 44 (1293) 643-900
From Asian/Pacific Rim countries
886 (2) 248-4072
InternetE-Mail:
[email protected]
World Wide Web:
http://www.viewsonic.com