VigilLink VLVW-MX29P User manual

VLVW-MX29P
2X9 HDMI 2.0 Videowall processor 18Gbp
VER 1.02

Thank you for purchasing this product
Please read these instructions carefully for optimum performance and safety before connecting,
operating, or adjusting this product. Please keep this manual for future reference.
A surge protection device recommended
This product contains sensitive electrical components that electrical spikes may damage,
surges, electric shocks, lightning strikes, etc. The use of surge protection systems is highly
recommended to protect and extend the life of your equipment.
Table of Contents
1. Introduction.....................................................................................................................
1
2. Features...........................................................................................................................
1
3. Package Contents. ........................................................................................................
1
4. Specifications. ................................................................................................................
2
5. Operation Controls and Functions................................................................................
2
6. RS-232/LAN Control Connection...................................................................................
4
6.1. RS-232 Control Connection. ...................................................................................
4
6.2. Network Control Connection. ................................................................................
4
7. PC Tool User Guide.........................................................................................................
5
8. Safety Instructions. .........................................................................................................
11
9. Connection Diagram. ....................................................................................................
12

- 1 / 12 -
1. Introduction
This product is an HDMI 2.0 Video Wall controller with 2 HDMI inputs, 2 HDMI loop outputs,
and 9 HDMI scaling outputs for video wall processing. The Toslink jack terminal provides
analog L/R audio and digital SPDIF audio output. The 5-pin phoenix jacket provides balanced
L/R audio output. The product also supports the RS-232 bypass feature for the daisy chain
and cascade connection among different units.
2. Features
☆HDMI 2.0 and HDCP 2.2 compliant
☆Supports multi-resolution up to 3840x2160@60Hz video output for video wall
☆Supports Bezel Compensation with two modes
☆Supports 2 channels HDMI loop out
☆Supports PIP on a video wall
☆Supports 180º rotation
☆Supports RS-232 and TCP/IP control
☆Supports CEC control with displayers by PC Tool or commands
3. Package Contents
①1 x Ultra HD Video Wall Processor
②1 x AC Power Cord
③1 x 5-pin Phoenix Connector
④2 x 3-pin Phoenix Connector
⑤1× RS232 to Phoenix Cable
⑥1× Cat 6 cable
⑦1× USB to RS232 Cable
⑧1× User Manual

- 2 / 12 -
4. Specifications
Technical
HDMI Compliance
HDMI 2.0
HDCP Compliance
HDCP 2.2/1.4
RS-232
Baud rate: 57600, Data bit: 8, Stop bit: 1, no parity
1024x768@60, 1280x800@60, 1280x1024@60,
1280x960@60, 1360x768@60, 1366x768@60,
1440x900@60, 1400x1050@60, 1600x900@60,
Input Video Formats
1600x1200@60, 1680x1050@60, 1920x1200@60,
480p@60, 576p@50, 720p@50, 720p@60, 1080i@50,
1080i@60, 1080p@24, 1080p@25, 1080p@30, 1080p@50
1080p@60, 3840x2160@24, 3840x2160@25,
3840x2160@30, 3840x2160@50, 3840x2160@60,
4096x2160@24, 4096x2160@30, 4096x2160@50,
4096x2160@60
Audio Format 2.0 channel, 5.1 channel, LPCM, Dolby, AC3, DTS
ESD Protection
Human-body Model:
±8kV (Air-gap discharge) , ±4kV (Contact discharge)
Mechanical
Housing
Metal Enclosure
Color Black
Dimension 430mm (W)×220mm (D)×44mm (H)
Weight
5Kg
Supply Voltage
110-220V AC
Operating Temperature 0°C ~ 40°C / 32°F ~ 104°F
Storage Temperature -20°C ~ 70°C / -4°F ~ 158°F
Relative Humidity
10%~50% RH (Non-Condensation)
5. Operation Controls and Functions
Front Panel

- 3 / 12 -
No.
Name
Function Description
1
Power LED
The power LED will be on when the unit is powered on.
2INPUT LED The LED will be on when the corresponding HDMI input port is
connected to an active HDMI source device.
3LOOP LED
The LED will be on when the corresponding LOOP OUT port is
connected to the HDMI display device.
4OUTPUT LED
(1-9)
The LED will be on when the corresponding HDMI output port is
connected to the HDMI display device.
Rear Panel
No.
Name
Function Description
1
INPUTS HDMI signal input ports connect to HDMI source devices such
as DVD or PS4 with HDMI cable.
2
LOOP OUT
HDMI signal loops out ports. Loop out HDMI A/B signal
downstream. The RS-232 command can configure it.
3
OUTPUTS
HDMI signal scaling output for video wall.
4
110-240VAC
110-240V AC power input port.
5
GND
Ground the product housing.
6
AUDIO
OUTPUT
TOSLINK:
• Analog L/R audio output
3.5mm Stereo Jack. 20Hz ~ 20kHz, 1.5Vrms max
• Digital SPDIF audio output
BALANCED OUT: Balanced audio output port. 5-pin phoenix
connector, 20Hz ~ 20kHz, 1.5Vrms max.
BALANCED OUT: Balanced audio output port. 5-pin phoenix
connector, 20Hz ~ 20kHz, 1.5Vrms max.
7
SERVICE
Firmware update port.
8
CONTROL
RS232: Bypass RS232-CTL commands to the next unit.
RS232-CTL: External RS-232 control, Baud Rate: 57600
Data Bits:8, Parity: None Stop Bits:1
LAN: Network port for TCP/IP control. Connect to an active
Ethernet link with an RJ45 cable.

- 4 / 12 -
3
-pin Phoenix Connector
RS-232
RS-232 to USB cable
6. RS-232/LAN Control Connection
6.1 RS-232 Control Connection
The product supports RS-232 control. Connect the RS232-CTL port of the product to a PC via
a serial cable, as shown in the following figure:
G
PC
6.2 Network Control Connection
The product also supports Network control. Connect the LAN port of the product to a PC via
a UTP cable, as shown in the following figure:
PC

- 5 / 12 -
7. PC Tool User Guide
The PC tool is an installation-free control software that supports both UART and network
control. It consists of five parts: Matrix Switch, Signal Setting, FineTune: PQ, Video Wall,
and CEC Control. The UI is as follows:
■Matrix Switch Page
1. You can select UART (with RS232 cable) or Network to connect the device; the
baud rate is57600 bps.
2. Select the input source for each scaling output port.
3. "AllSet" function: Select HD A or B input source to all the scaling output.
4. Select the input source for the B/MAIN output port.
5. Select an audio source for balanced audio output and Mini Toslink output.
6. Reset: The PC tool supports a reset system to recover factory configuration.
7. EDID Control: Click the "EDID" button on the Matrix Switch page, and there will be a
pop-upEDID control window.
a) Read each scaling output port downstream EDID and
save it as a BIN file.
b) Open an existing EDID file and write to the HDMI A
and B input port as Manual EDID.
c) Select predefined EDID and write to HDMI A and B
input ports.

- 6 / 12 -
The predefined EDID option is as below:
4K60-2.0CH
1920x1200-2.0CH
4K60-5.1CH
1680x1050-2.0CH
4K30-2.0CH
1600x1200-2.0CH
4K30-5.1CH
1440x900-2.0CH
1080P-2.0CH
1400x1050-2.0CH
1080P-5.1CH
1360x768-2.0CH
720P-2.0CH
1280x1024-2.0CH
1024x768-2.0CH
Manual
■Signal Setting Page
Users can read the resolution of each input port and set the resolution of each scaling output.
Available output resolutions:
No. Output Resolution Setting No. Output Resolution Setting
1
3840x2160p 60Hz
9
1440x1050 60Hz
2
3840x2160p 50Hz
10
1366x768 60Hz
3
3840x2160p 30Hz
11
1360x768 60Hz
4
3840x2160p 25Hz
12
1280x1024 60Hz
5
1920x1200 60Hz
13
1280x768 60Hz
6
1920x1080p 60Hz
14
1280x720p 60Hz
71920x1080p 50Hz 15
1280x720p 50Hz
8
1600x1200 60Hz
16
1024x768 60Hz
Note: 3840x2160 25/30Hz can only be used for standalone display, not video wall.

- 7 / 12 -
■FineTune: PQ Page
You can read and set each output's Brightness/Contrast/Saturation/Sharpness.
Note: Suggest always use the default setting 50/50/50/50. Do not change the default
settings without special conditions; If there is a problem after changing, click "Reset" to
return to the factory settings.
■CEC Control Page
If Auto Power On is enabled, whenever the product is turned on, it will turn on all
displayers connected to it.
The product supports CEC functions, including Power on/off, Volume+/-, and Mute/Unmute.

- 8 / 12 -
■Video Wall Page
This page is used to configure a group of outputs to function as a video wall.
1. Use the Video Wall Setting controls to change how the displays are arranged on the Video
Wall page:
a. Adjust the Rows and Columns sliders to change the displayed screen arrangement to
permit proper Drag-and-Select of the desired screens for the video wall.
b. Change the Available slider to set how many outputs will be used for the Video Wall.
c. Click the "Set" button to change the Screen configuration.
2. Use the left mouse button to drag-select the screens set for video wall mode.The
selected screens will be shown as bright blue.
3. Use the right mouse button to open a menu.
4. Select "Screen Stitching" from the menu to program the video wall mode. The
selectedscreens will now be shown as bright green.
5. To change the displayed image, use the methods detailed in the section Controllingthe
Matrix Switcher; right-click to open the pop-up menu and select the desired input from the
"Input Select" menu option.