Viking Range Brigade CVGSO100 User manual

Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
[phone]
For product information,
call 1-888-845-4641
or visit our web site at
www.brigade.ca
F21108 EN (030113)
BRIGADE
TM
Installation Guide
Professional Built-In Gas
Thermal-Convection Ovens
All manuals and user guides at all-guides.com
all-guides.com

IMPORTANT
3
–Please Read and Follow
Table of Contents
Warnings & Important Safety Information_______________________________________________3
Dimensions _________________________________________________________________________6
Specifications _______________________________________________________________________7
Cutout Dimensions __________________________________________________________________8
Clearance Dimensions________________________________________________________________9
Electrical & Gas Requirements _______________________________________________________10
General Information ________________________________________________________________11
Installation ________________________________________________________________________12
Door Removal _________________________________________________________________13
Connecting Gas & Electrical _____________________________________________________14
Final Installation ________________________________________________________________15
Door Replacement & Adjustment ________________________________________________16
Final Preparation ___________________________________________________________________17
Performance Checklist ______________________________________________________________18
Service & Registration_______________________________________________________________19
• Before beginning, please read these
instructions completely and carefully.
• DO NOT remove permanently affixed
labels, warnings, or plates from product.
This may void the warranty.
• All local and national codes and ordinances
must be observed. Installation must
conform with local codes or in the absence
of codes, the National Fuel Gas Code ANSI
Z223.1 NFPA54-latest edition.
• The installer must leave these instructions
with the consumer who should retain for
local inspector’s use and for future
reference.
In Canada: Installation must be in accordance
with the current CAN/CGA B149.1 & 2 Gas
Installation codes and/or local codes. Electrical
installation must be in accordance with the
current CSA C22.1 Canadian Electrical Codes
Part 1 and/or local codes.
In Massachusetts: All gas products must be
installed by a “Massachusetts” licensed
plumber or gasfitter. A “T” type handle
manual valve must be installed in the gas
supply line to the appliance.
Your safety and the safety of others is
very important.
We have provided many important safety
messages in this manual and on your
appliance. Always read and obey all
safety messages.
This is the safety alert symbol. This
symbol alerts you to hazards that
can kill or hurt you and others.
All safety messages will be preceded by
the safety alert symbol and the word
“DANGER,” “WARNING” or “CAUTION.”
These words mean:
Hazards or unsafe practices
which WILL result in severe personal
injury or death
DANGER
Hazards or unsafe practices
which COULD result in severe personal
injury or death
Hazards or unsafe practices which
COULD result in minor personal injury or
property damage
All safety messages will identify the
hazard, tell you how to reduce the chance
of injury, and tell you what can happen if
the instructions are not followed.
WARNING
CAUTION
All manuals and user guides at all-guides.com

5
DANGER
Electrical shock hazard.
To avoid risk of electrical shock,
personal injury or death; verify
your appliance has been
properly grounded in accordance with
local codes or in absence of codes, with
the National Electrical Code (NEC).
ANSI/NFPA 70-latest edition.
DANGER
Fire/explosion hazard.
IF THE INFORMATION IN
THIS MANUAL IS NOT
FOLLOWED EXACTLY, A
FIRE OR EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE,
PERSONAL INJURY, OR DEATH.
• DO NOT store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
• WHAT TO DO IF YOU SMELL GAS:
–DO NOT try to light any appliance.
–DO NOT touch any electrical switch.
–DO NOT use any phone in your
building.
–Immediately call your gas supplier from
a neighbor’s phone.
–Follow the gas supplier’s instructions.
–If you cannot reach your gas supplier,
call the fire department.
• Installation and service must be
performed by a qualified installer, service
agency, or the gas supplier.
DANGER
Chemical hazard.
To avoid risk of property
damage and/or personal injury
or death; this appliance is not
to be used as a heating source.
• Benzene is a chemical which is part of
the gas supply to this cooking product,
which is consumed in the flames during
combustion. Exposure to a small
amount of benzene is possible if a gas
leak occurs. Formaldehyde and soot are
by-products of incomplete combustion.
• This appliance contains or produces
chemicals which can cause serious
injury or death and which are known to
the state of California to cause cancer,
birth defects or other reproductive harm.
To reduce the risk from substances in
the fuel or from fuel combustion make
sure this appliance is installed,
operated, and maintained in accordance
to the instructions in this document.
DANGER
Gas leak hazard.
To avoid risk of personal injury
or death; leak testing of the
appliance must be conducted
according to the manufacturer’s
instructions. Before placing appliance in
operation, always check for gas leaks
with soapy water solution.
• DO NOT USE AN OPEN FLAME TO
CHECK FOR GAS LEAKS.
WARNING
Moving hazard.
To avoid risk of severe
personal injury; this appliance
requires two or more personnel
while handling and moving. Possible
use of appliance moving devices is
recommended.
WARNING
The use of cabinets for storage above
the oven may result in potential
fire or burn hazard.
WARNING
The misuse of the oven door(s) (e.g.
stepping, sitting, or leaning on them)
can result in hazards or injuries and
damage to the product.
WARNING
DO NOT use the handle or oven door to
lift the oven. Remove door before
installation to ensure that it is
not used to lift the unit.
WARNING
NEVER use this appliance as a space
heater to heat or warm the room. Doing
so may result in carbon monoxide
poisoning and overheating of the oven.
WARNING
No attempt should be made to operate
the appliance during power failure.
4
IMPORTANT–Please Read and Follow
WARNING
To prevent possible damage to cabinets
and cabinet finishes, use only materials
and finishes that will not discolor or
delaminate and will withstand temperatures
up to 194°F (90°C). Heat resistant
adhesive must be used if the product is to
be installed in laminated cabinetry. Check
with your builder or cabinet supplier to
make sure that the materials meet these
requirements.
A GFI
shall be used if required by NFPA-70 (National Electric Code), federal/state/local
laws, or local ordinances.
• The required use of a GFI is normally related to the location of a receptacle with respect to
any significant sources of water or moisture.
• Viking Range Corporation will NOT warranty any problems resulting from GFI outlets which
are not installed properly or do not meet the requirements below.
If the use of a GFI is required , it should be:
• Of the receptacle type (breaker type or portable type NOT recommended)
• Used with permanent wiring only (temporary or portable wiring NOT recommended)
• On a dedicated circuit (no other receptacles, switches or loads in the circuit)
• Connected to a standard breaker of appropriate size (GFI breaker of the same size NOT
recommended)
• Rated for Class A (5 mA +/- 1 mA trip current) as per UL 943 standard
• In good condition and free from any loose-fitting gaskets (if applicable in outdoor situations)
• Protected from moisture (water, steam, high humidity) as much as reasonably possible
All manuals and user guides at all-guides.com

Specifications
7
Dimensions
6
Built-In 30“W. Gas Oven
Description
CVGSO100
Overall width 29-1/2” (74.9 cm)
Overall height 31” (78.7 cm)
Overall depth from
rear
To edge of door—24-7/8” (63.2 cm)
To end of handle bracket—27-3/8” (69.5 cm)
With door open—43-1/2” (110.5 cm)
Cutout width 28-5/8” (72.7 cm)
Cutout height 30-5/8” (77.8 cm)
Cutout depth 24” (61.0 cm) min.; unit extends into cutout 23-7/8” (60.6 cm); cord protrudes 1/2”
(1.3 cm) beyond 23” (58.4 cm)
Cutout height
from floor 17” (43.2 cm) min.
Gas requirements Shipped natural or LP/Propane gas; LP must be specified after color code; accepts
standard residential 1/2” (1.3 cm) ID gas service line.
Gas manifold
pressure Natural 5.0” W.C.P. / Liquid propane L/P 10.0” W.C.P.
Electrical
requirements
120 VAC/60 Hz 4 ft. (121.9 cm) 3-wire cord with grounded 3-prong plug attached to
product. Flexible cord/connector must be 1/2” ID (1.3 cm). Cord must be agency
approved for use with household gas ovens.
Maximum amp usage 1.2 amps
Infrared broil
burner rating
18,000 BTU Nat. (5.3 kW)
Bake burner rating One 30,000 BTU Nat./LP (8.8 kW)
Oven interior width 23” (58.4 cm)
Oven interior height 16-1/8” (40.9 cm)
Oven interior depth 15-3/8” (39.1 cm)
Oven volume Total oven capacity—4.0 cu. ft.
AHAM Standard 3.3 cu. ft.*
Approximate
shipping weight 310 lbs. (139.5 kg)
24-7/8”
(63.2 cm)
21-5/16”
(54.1 cm)
13-1/4”
(33.7cm)
27-3/8”
(69.5 cm)
26-7/8”
(68.3 cm)
29-1/2”
(74.9 cm)
30-1/2”
(77.5 cm)
Gas inlet
31”
(78.7 cm)
18-5/8”
24-7/8” (63.2 cm)
27-3/8” (69.5 cm)
43-1/2” (110.5 cm)
(47.3 cm)
1/8”*
(.3 cm)
17-3/16”
(43.6 cm)
1/2”
(1.3 cm)
23-1/2” (60.0 cm)
Gas inlet
21-5/16”
(54.1 cm)
*Note: The AHAM Stadard for measuring oven capacity subtracts the door plug and convection baffle
dimension from the total oven volume.
*Note: Bottom of cutout to bottom of trim–used for installing warming drawer below oven.
Built-In 30”W. Gas Oven
All manuals and user guides at all-guides.com

Clearance Dimensions
9
Note: Door handle of oven should be 36”
(91.4 cm) above the floor.
Note: The grounded electrical socket should
be placed above or below cutout(s).
CAUTION
Burn hazard.
To avoid risk of personal injury;
the use of cabinets for storage
above the appliance may result
in a potential burn hazard. Combustible
items may ignite, metallic items may
become hot and cause burns.
CAUTION
To prevent possible damage to cabinets
and cabinet finishes, use only moisture
resistant materials and finishes that will
withstand temperature up to 190°F
(88°C). When cabinets are covered with
laminates, an appropriate heat-resistant
adhesive must be used. Consult your
manufacturer for proper specifications.
Electrical Requirements
Check your national and local codes
regarding this unit. These ovens require
3-wire, 120 VAC/60 Hz.
See “Connecting
Gas & Electrical” section for grounding
instructions.
Gas Connection
The gas supply (service) line must be the
same size or greater than the inlet line of the
appliance. This oven uses a 1/2” (1.3 cm) ID
NPT (Sch40) inlet. Sealant on all pipe joints
must be resistive to LP gas.
These ovens are designed specifically for
natural gas or liquid propane (LP) gas. It is
shipped from the factory adjusted for use
with natural or propane (LP) gas. Before
beginning installation verify that the
model is compatible with the intended
gas supply.
Manual shut-off valve:
This installer-supplied valve must be installed
in the gas service line before the appliance
in the gas stream and in a location where it
can be reached quickly in the event of
an emergency.
In Massachusetts: A “T” handle type
manual valve must be installed in the gas
supply line to the appliance.
IMPORTANT: Any conversion required
must be performed by your dealer or a
qualified licensed plumber or gas service
company. Please provide the service person
with this manual before work begins.
WARNING
Electrical shock hazard.
To avoid the risk of electrical
shock, personal injury or death;
verify electrical power is turned
off at the breaker box and gas supply is
turned off until the oven is installed and
ready to operate, installation by an
authorized installer only.
Electrical & Gas Requirements
Cutout Dimensions
8
24”
(61.0 cm) min.
1-1/2”
(3.8 cm)
3”
(7.6 cm) dia.
14-1/4”
(36.2 cm)
30-5/8”
(77.8 cm)
Electrical outlet to be located
in shaded area on rear wall
Gas inlet
location
3”
(7.6 cm)
28-5/8”
(72.7 cm)
21-5/16”
(54.1 cm)
17”
(43.2 cm) min.
30”
(76.2 cm)
Recommended
30”W. Cutout
All manuals and user guides at all-guides.com

11
General Information
READ AND FOLLOW ALL WARNING
AND CAUTION INFORMATION WHEN
INSTALLING THIS APPLIANCE.
• All openings in the wall behind the
appliance or in the floor under the
appliance should be sealed.
• Keep appliance area clear and free from
combustible materials, gasoline and other
flammable vapors.
• Disconnect the electrical supply prior to
servicing or cleaning.
• When removing the appliance for cleaning
or service, disconnect AC power supply
and carefully remove the appliance by
pulling forward.
• Electrical requirements are listed in the
product specifications under the “Electrical
& Gas Requirements” section.
• Do not obstruct the flow of combustion and
ventilation air.
Moving, Handling, and Unpacking
Remove and discard all packing materials,
including cardboard and tape on the outside
and inside of the ovens.
Some stainless steel parts may have a plastic
protective wrap which must be peeled off.
The interior should be washed thoroughly
with hot, soapy water to remove film
residues and any dust or debris before being
used, then rinsed and wiped dry. Solutions
stronger than soap and water are rarely
needed.
Recommendations for Unpacking
• Products are shipped on pallets with foam
footings and corrugated inner-packing and
exterior hoods.
• Products are anchored to the pallet using
metal straps that are screwed to the
bottom of the product and the pallet.
• DO NOT remove protective packaging
until you are ready to perform the
installation.
• To remove the packaging, first remove the
staples located at the bottom perimeter of
the corrugated cover.
• Remove the corrugated cover by lifting it
off the product and remove the inner-
packing.
• Detach the product from the metal anchor
strip by removing the attachment screw.
CAUTION
Avoid any damage to oven vents. The vents
need to be unobstructed and open to provide
proper airflow for optimal oven performance.
CAUTION
The cooling fan should be operating when
the unit is in operation. If you notice the
cooling fan is not operating or you observe
unusual or excessive noise coming from the
cooling fan, contact an authorized service
center before continuing operation. Failure to
do so can result in damage to the oven or
surrounding cabinets.
Electrical & Gas Requirements (cont.)
10
Pressure Regulator:
• All heavy-duty, commercial type cooking
equipment must have a pressure regulator
on the incoming service line for safe and
efficient operation, since service pressure
may fluctuate with local demand. External
regulators are not required on this oven
since a regulator is built into each unit at
the factory. Under no condition bypass
this built-in regulator.
• Manifold pressure should be checked with
a manometer, natural gas requires 5.0”
W.C.P. and LP gas requires 10.0” W.C.P.
Incoming line pressure upstream from the
regulator must be 1” W.C.P. higher than
the manifold pressure in order to check
the regulator. The regulator used on these
ovens can withstand a maximum input
pressure of 1/2” PSI (14.0” W.C.P.). If the
line pressure is in excess of 1/2” PSI
(14.0” W.C.P.), a step down regulator
will be required.
• The appliance must be disconnected from
the gas supply piping system during any
pressure testing of that system.
Flexible Connections:
If the unit is to be installed with flexible
couplings and/or quick-disconnect fittings,
the installer must use a heavy-duty AGA
design-certified flexible connector of at least
1/2” (1.3 cm) ID NPT (with suitable strain
reliefs) in compliance with ANSI Z21.41
and Z21.69.
Rigid Connections:
• Incoming gas from the service supply is
brought from an intake pipe (not supplied)
to the back center of the unit through the
shut-off valve (not supplied) to the
regulator.
(See “Cutout Dimensions”
section for gas inlet location.)
In Canada: CAN 1-6, 10-88 metal
connectors for gas appliances and CAN
1-6.9 M79 quick disconnect devices for use
with gas fuel.
In Massachusetts: This appliance must be
installed with a 36” (3-foot) long flexible
gas connector.
CAUTION
Before placing the oven into operation,
always check for gas leaks with a soapy
water solution or other acceptable
method. DO NOT USE AN OPEN FLAME
TO CHECK FOR LEAKS.
All manuals and user guides at all-guides.com
all-guides.com

13
2
1
2
3
2
2
1
Open door completely. Place pin in pin hole.
Note: Two pins included.
Remove hinge trim screws. Take off hinge trim.
4 5
Close until pins stop door. Lift door up and out.
Note: Do not lift door using handle.
NOTICE
DO NOT use the handle or oven door to
lift the oven. Remove door before
installation to ensure that it is not used to
lift the unit. DO NOT lift or carry the door
by the handle.
Removing the door must be done by your
dealer, a qualified licensed plumber, or
certified gas installer.
Installation
1
Remove wooden brace on front of pallet.
Door Removal
Installation
12
Note: A minimum of 2” spacing above and
below the oven to any adjacent items is
required for ventilation purposes.
• It is recommended that 3/4” or larger
material be utilized to create a support
platform for this appliance.
• BE SURE that support for this appliance is
perpendicular to the front facing of the
wall or cabinet before you perform the
installation.
• Use of a hydraulic lift is recommended for
the installation of double oven units.
• All openings in the wall behind the
appliance or in the floor under the
appliance should be sealed.
• Keep appliance area clear and free from
combustible materials, gasoline and other
flammable vapors.
• WARNING: DO NOT USE AN
EXTENSION CORD WITH THIS
APPLIANCE. SUCH USE MAY RESULT IN
FIRE, ELECTRICAL SHOCK OR OTHER
PERSONAL INJURY.
General Information (cont.)
Recommendations for Moving
• The appliance is heavy – use extreme care
when handling!
NOTICE
DO NOT use the handle or oven door to
lift the oven. Remove door before
installation to ensure that it is not used to
lift the unit. DO NOT lift or carry the door
by the handle.
Removing the door must be done by your
dealer, a qualified licensed plumber, or
certified gas installer.
• Only proper equipment should be used to
move products.
• ALWAYS take steps to protect flooring at
the installation location when moving
products.
Site Preparation
Note: It is recommended that a thorough
site inspection be conducted PRIOR to
unpacking and moving this appliance.
• WARNING: DO NOT use the handle or
oven door to lift the oven. Remove door
before installation to ensure that it is not
used to lift the unit. Make sure pins are
inserted into hinges before removing door
to prevent personal injury to hands and/or
fingers. Do not lift or carry the door by
the handle.
• Confirm available access to adequate
power – see electrical requirements.
All manuals and user guides at all-guides.com

15
12
Remove racks. Unscrew pallet screws from side of oven.
34
Lift oven into position. Push oven straight into cabinet.
56
Attach screws to the side of the framing.
Note: Four screws (two on each side).
(Screws not included.)
Replace racks.
Final Installation
14
Note: Refer to “Electrical & Gas
Requirements” section for proper
installation information.
Connect gas and electrical. Before placing appliance in
operation, always check for gas leaks. This must be
performed by your dealer, a qualified licensed plumber,
or gas service company.
Connecting Gas & Electrical
DANGER
Gas leak hazard.
To avoid risk of personal injury
or death; leak testing of the
appliance must be conducted
according to the manufacturer’s
instructions. Before placing appliance in
operation, always check for gas leaks
with soapy water solution.
• DO NOT USE AN OPEN FLAME TO
CHECK FOR GAS LEAKS.
WARNING
Electrical shock hazard.
To avoid the risk of electrical
shock, personal injury or death;
verify your appliance has been
properly grounded in accordance with
local codes or in absence of codes, with
the National Electrical Code (NEC).
ANSI/NFPA 70-latest edition.
1
All manuals and user guides at all-guides.com

17
Final Preparation
1. Some stainless steel parts may have a
plastic protective wrap, which must be
peeled off. All stainless steel body parts
should be wiped with hot soapy water
and with liquid cleaner designed for this
material. If build-up occurs, do not use
steel wool, abrasive cloths, cleaners or
powders! If it is necessary to scrape
stainless steel to remove encrusted
materials, soak with hot, wet cloths to
loosen the material, then use a wood or
nylon scraper. DO NOT use a metal knife,
spatula, or any other metal tool to scrape
stainless steel! Scratches are almost
impossible to remove.
2. The interior of the oven should be washed
thoroughly with hot, soapy water to
remove film residues and installation
debris before being used for food
preparation, then rinsed and wiped dry.
Solutions stronger than soapy water are
rarely needed.
16
12
Replace door. Open door completely. Reinstall hinge trim plates.
Note: Screw holes may need to be re-aligned.
34
Take out pins.
Note: To adjust door turn adjustment screw
clockwise (up) or counterclockwise (down).
Close door.
Door Replacement & Adjustment
All manuals and user guides at all-guides.com

19
Service & Registration
Only authorized replacement parts may be used in performing service on the appliance.
Do not repair or replace any part of the appliance unless specifically recommended in the
manual. All servicing should be referred to a qualified technician.
Contact Viking Range Corporation, 1-888-845-4641, for the nearest service parts distributor in
your area or write to:
VIKING RANGE CORPORATION
PREFERRED SERVICE
1803 Hwy 82W
Greenwood, Mississippi 38930 USA
Record the following information indicated below. You will need it if service is ever required.
Model number ____________________________________________________________________________________
Serial number _____________________________________________________________________________________
Date of purchase __________________________________________________________________________________
Date installed ______________________________________________________________________________________
Dealer's name _____________________________________________________________________________________
Address ___________________________________________________________________________________________
These installation instructions should remain with the unit for future reference.
The model and serial number for your oven can be found by opening the door and looking on
the front frame to the left of the oven cavity.
18
Performance Checklist
A qualified installer should carry out the
following checks:
1. Check oven bake function–bake burner on
full power. Tubular bake burner should
reignite on both sides. Convection bake
function–bake burners the same with the
convection fan on.
2. Check oven broil function–infrared broil
screen should glow. Covection broil function
is the same with convection fan on.
3. Check air shutter adjustment; sharp blue
flame, no yellow tipping, no sooting, no
flame lifting.
4. Check for gas leaks (odor) at all gas
conversions.
5. Check convection fan switch and fan
operation.
6. Check light switch and light operation.
7. Check for proper fit of door seals.
OVEN
LIGHT
OVEN FUNCTION
OFF
BAKE
SET
OVEN
BROIL
CONV.
BROIL
CONV.
BAKE
TEMPERATURE
OFF
400
200
300 500
BROIL
MIN/SEC
TIMER
BAKE
TIMER
START
TIME
CLOCK
OVEN
LIGHT
OFF
BROIL
CANCEL
CLOCK
TIMER
COOK
TIME
BROIL
HI/LOW
DOWN
BAKE
TEMP UP
BAKE
CONVECTION
BAKE
CONVECTION
BROIL
Electronic
Timing Center
Off/On
Indicator light
Interior
Oven Light Control
Temperature
Control
Oven Function Selector
All manuals and user guides at all-guides.com