Viking Stage Lighting VK540 SURGE WALL WASH User manual

VK540 SURGE WALL WASH
User Manual
M136
Introduction
Specification
Rated Voltage：AC100V～240V 50-60HZ
Rated Power: 450W
LED Qty: 36x15W High power RGBW LEDs
Beam Angle: 25° Optional 60° Frost Filter available
IP 65 Rated for Exterior Use
DMX Mode：2/3/4/13/16/29CH
Packing Size：H:287 W:481 D220mm (without stand or bracket)
Net weight：13.2Kg
Dmx on 3 Pin XLR IP65 Connectors
Power in/out on TrueCon IP65 Connectors
3 kinds of control model: DMX512,WDMX,Master/slave.
2.4G Sweedish Wireless DMX control standard.
Functions Dimmer, Strobe, RGBW, Macro Colour,Colour Jump,Colour Fade
Rainbow,Auto Program,Auto Speed,Dimmer Curve
Stand Alone Mode and DMX Mode
Refresh Rate 3000Hz
6 DMX Modes 2/3/4/13/16/29 channels
2 Dimmer Modes & 4 kinds of Dimmer Curves
Display can be inverted when unit is hung
Fan Cooling System on Auto and high speed

Product Introduction
Rigging:
The VK540 SURGE can be hung using the omega clamps supplied or
stood on the ground using the custom Floor Stand
Optional equipment include Barndoors and a 60 degree Frost Filter
60 Deg Frost Filter
Barndoor
Omega Clamp to hang light
Floor Stand

Operating Instructions
Control board function
Button Function
Mode Choose mode or function exit
ENTER Current show menu or enter into the current selected function
UP Increase the value
DOWN Decrease the value
• When the spotlight is properly connected to the mains, “Software Update ,Please Wait” (only
for internal purposes), “Welcome to LED Wash”, the model name and software version appear
successively on the display during the start-up process. After this operation, the spotlight is
ready for use and starts in the mode that was previously selected.
• If one of the DMX operating modes is activated and there is no DMX signal at the DMX input,
the display starts to flash after a few seconds.
• After approximately 30 seconds of inactivity, the display will automatically show the currently
active operating mode.
• Fast Access Feature: In order to simplify the menu guide, the device has an intelligent menu
structure which allows menu and sub-menu items
that were last selected to be accessed directly. 1. Pressing MODE and ENTER simultaneously
will take you directly to the sub-menu item that was last edited and allows you to instantly
change the corresponding value as desired (DMX start address and all operating modes). 2.
Pressing MODE will take you directly to the menu item that was last selected and edited; now
press ENTER to instantly access the sub-menu item that was selected and edited last (DMX
start address and all operating modes).
Menu Map

Menu Instruction：
MAIN DISPLAY DMX MODE
In the upper line of the display,the DMX (DMX 2Ch,3Ch1,3Ch2,4Ch,13Ch,16Ch,29Ch)is display and the
DMX start address is prominently shown in the centre(for example DMX13Ch and ADDRESS 001).As soon
as the DMX signal is interrupted,the display starts flashing；if the DMX signal is present again,the display
stops flashing.
MAIN DISPLAY SLAVE MODE
In the upper line the display,the preset DMX is displayed and “SALVE”is prominently shown in the center.
As soon as the control signal is interrupted, the display starts flashing;if the control signal is present again,
the display stops flashing.
MAIN DISPLAY STANDALONE MODE
In the upper line of display,the preset DMX mode is displayed and the currently activated Auto mode, static
mode STATIC,or colour macro mode COLOUR MACRO.
SETTING THE DMX START ADDRESS(ADDRESS)
Pressing MODE will take you the selection menu for system setting.Using UP and DOWN,select the menu
item“ADDRESS”(colored background)and confirm with ENTER.This is followed by the display of the menu
item“Set DMX Address”.Press ENTER again to select the DMX start address as desired button using the
UP and DOWM button. If the start address is changed,the address color changes to red. Confirm with
ENTER and Press MODE twice to return to the main display.The main display is automatically activated if
no input is made within about 30 seconds.
SETTING THE DMX SIGNAL SELECT(DMX SIGNAL SELECT)
Pressing MODE will take you to the selection menu for system settings. Using UP and DOWM,select the
menu item“MODE”(colored background) and confirm with ENTER. Now use the UP and DOWN buttons
once more to select the “DMX SIGNAL SELECT”sub-menu item and confirm button pressing ENTER.
Using UP and DOWN, select the desired DMX mode(DMX,Wireless DMX)and confirm with ENTER. Press
MODE twice to return to the main display. the main display is automatically activated if no input id made
within about 30 seconds. You will find tables with the channels of the different DMX Signal in this manual
under DMX SIGNAL CONTROL.
SETTING THE DMX MODE(DMX MODE)
Pressing MODE will take you to the selection menu for system settings. Using UP and DOWM, select the
menu item“MODE”(colored background) and confirm with ENTER.Now use the UP and DOWN buttons
once more to select the “DMX MODE”sub-menu item and confirm button pressing ENTER.Using UP and
DOWN,select the desired DMX mode(DMX 2Ch,DMX 3Ch1,DMX 3Ch2,DMX 4Ch,DMX 13Ch,DMX
16Ch,DMX29 Ch)and confirm with ENTER.Press MODE twice to return to the main display.the main
display is automatically activated if no input id made within about 30 seconds.You will find tables with the
channels of the different DMX modes in this manual under DMX CONTROL.

SETTING THE SLAVE MODE(Slave)
Pressing MODE will take you to the selection menu for system settings. Using UP and DOWN, select the
menu item“MODE”(colored background) and confirm with ENTER.Now use the UP and DOWN buttons
once more to select the “DMX MODE”sub-menu item and confirm button pressing ENTER and press
MODE twice to return to the main display.The main display id automatically activated if no id made within
about 30 seconds, Connect the slave and the master unit(same model)with a DMX cable and activate one
of the standalone modes(Auto,Static,Color Macro)on the master unit.Now the slave unit follows the master
unit.
SETTING THE AUTOMATIC CONTROL MODE(Auto)
Pressing MODE will take you to the selection menu for system settings. Using UP and DOWN, select the
menu item“MODE”(colored background) and confirm with ENTER. Now use the UP and DOWN buttons
once more to select the “Auto”sub-menu item and confirm button pressing ENTER, Using UP and
DOWN ，you can now select between Auto additional sub-menu items“Auto Fading”and“Auto
Jumping”.Select“Auto Fading”, Press ENTER again to select the auto fading speed(000-255) as desired
button using the UP and DOWM button. If set the “Auto Jumping”, Press ENTER again to select the auto
jumping speed(000-255) as desired button using the UP and DOWM buttons.
STATIC MODE(Static)
In the same way as with a DMX control unit, the static mode allows you adjust an functions such as
Dimmer ,Red,Green,Blue,White and Strobe directly on the device with values from 000 to 255.Thus, an
individual scene can be created without an additional DMX controller ,pressing MODE will take you to the
selection menu for system settings .Using UP and Down, select the menu item“Static”(colored
background) and confirm with ENTER, Use the UP and DOWN buttons to select the function of the LED
Wash that you wish to edit and confirm button pressing ENTER.The alue(dimmer ,Red,Green,Blue,
White,etc., see list)of the corresponding function can now be set from 000-255 and press ENTER to
confirm the input. Once all of the parameters have been set as desired, press MODE three to the main
display. The main display is automatically activated if no input made within 30 seconds.
STATIC
Dimmer 000 - 255 0% to 100%
Strobe
000 - 005 Strobe open
006 010 Strobe closed
011 - 033 Plus Random, slow->fast
034 - 056 Ramp up Random, slow -> fast
057- - 0796 Ramp down Random, slow -> fast
080 - 102 Random Strobe Effect, slow -> fast
103 - 127 Strobe Break Effect, 5s…..1s (Short burst with break)
128 - 250 Strobe slow -> fast <1Hz - 20Hz
251 - 255 Strobe open
Red 000 - 255 0% to 100%
Green 000 - 255 0% to 100%
Blue 000 - 255 0% to 100%
White 000 - 255 0% to 100%
Rainbow 000 - 005 Rainbow off
006 - 021 Rainbow1
022 - 037 Rainbow2
038 - 053 Rainbow3
054 - 069 Rainbow4
070 - 085 Rainbow5
086 - 101 Rainbow6
102 - 117 Rainbow7

118 - 133 Rainbow8
134 - 149 Rainbow9
150 - 165 Rainbow10
166 - 181 Rainbow11
182 - 197 Rainbow12
198 - 213 Rainbow13
214 - 229 Rainbow114
230 - 255 Rainbow15
Auto Program 000 - 005 No function
006 - 030 Auto Program1
031 - 055 Auto Program2
056 - 080 Auto Program3
081 - 105 Auto Program4
106 - 130 Auto Program5
131 - 155 Auto Program6
156 - 180 Auto Program7
181 - 205 Auto Program8
206 - 230 Auto Program9
231 - 255 Auto Program10
Auto speed 000 - 255 Auto speed
SETTING THE COLOR MACRO MODE(Color Macro)
Pressing MODE will take you to the selection menu for system settings. Using UP and DOWN, select the
menu item“MODE”(colored background) and confirm with ENTER. Now use the UP and DOWN buttons
once more to select the “Color Macro”sub-menu item and confirm button pressing ENTER, Using UP and
DOWN ，you can now select 15 different color macros are available as presets: “Red”, “Amber”,
“Yellow Warm”, “Yellow”,“Green”,“Turquoise”,“Cyan”,“Blue”, “Lavender”, “Mauve”,
“Magenta”,“Pink”,“Warm White”, “White”and“Cold White”,Press ENTER and exit. press MODE
three to the main display. The main display is automatically activated if no input made within 30 seconds.
DEVICE SETTINGS(Setting)
Pressing MODE will take you to the selection menu for system settings. Using UP and DOWN, select the
menu item“Setting”(colored background) and confirm with ENTER. You will then be taken to the
sub-menu to set the sub-menu items(set list).The main display is automatically activated if no input is made
within about 30 seconds.
setting
Display Rev = Flip Display ON =Rotation of the display by 180°
(e.g.over head installation)
OFF =no rotation of the display
Display = Display lighting ON =permanently on
OFF =deactivation after approx.1 minutes
of inactivity
DMX Fail = Operation status with DMX
signal interruption
Hold =last command is held
Blackout =activates Blackout
Dimmer Curve = Dimmer Curve Linear =The light intensity increases linearly
with the DMX value
Exp =Adjustment of the light intensity is
finer in the lower DMX value range
and coarser in the upper DMX value
range
Log =Adjustment of the light intensity is
coarser in the lower DMX value
range and finer in the upper DMX
value range

S Curve =Adjustment of the light intensity is
finer in the lower and upper DMX
value ranges and coaster in the
middle DMX value range
Dimmer Response = Dimmer response LED =The spotlight responds abruptly to
changes in the DMX value
Halogen =The spot behaves in a manner
similar to that of a halogen lamp with
gentle changes in brightness
White Balance = White balance Red,Green,
Blue,White
=Individual white balance. Cross-operating
mode setting of the 4 RGBW LED groups
Fan Set = Fan speed Auto =According to the LED temperature
to control the fan speed
High =The fan at high speed
Wireless DMX = Reset Wireless DMX
Memory
No =do not reset wireless DMX
Yes = Reset Wireless DMX Memory
Test = Function test OFF =stops the function test
ON =step-by-step function test of LEDs
Factory Reset = Reset to factory set OFF =do not perform reset
ON = Reset to factory setting
Key lock = The key lock switch OFF =Key lock closure
ON = Key lock closure, As the key lock
opens, display screen backlight 30
seconds out, button is locked, need
operation buttons, first to ENTER a
password to unlock, ENTER the
password to operation display panel
buttons UP, DOWM, UP, DOWN,
press ENTER to unlock,
DIMMER CURVES
DEVICE INFORMATION(System Info)
Pressing MODE will take you to the selection menu for system settings. Using UP and DOWN, select the
menu item“System Info”(colored background)and confirm with ENTER. You will then be taken to the
sub-mune to display the device information. Use the UP and DOWN panels again to select the desired
sub-menu item and then press ENTER to retrieve the information.

System Info
Software Ver = Display the device
software version
VR.xx
Temp info = Temperature display of the
LED unit
LED Temp XxC/xxF
Temp Unit Celsius(=display in degrees Celsius)
Fahrenheit(=display in degrees Fahrenhet)
Time info = Operating time display Power on Displays the tatal operating time in
hours
Last run hrs Displays the operating time since
the last operation
Press the MODE button repeatedly to return to the main display. The main display id automatically
activated if no input within about 30 seconds.
DMX Channel Table
2Ch mode
Ch. Function Values Sub-group
1 Dimmer 000 - 255 0%-100% Dimmer
2
Colour Macro
(override
RGBW)
000 - 005 Color OFF
Colour Macro
006 - 013 Red
014 - 021 Amber
022 - 029 Yellow Amber
030 - 037 Yellow
038 - 045 Green
046 - 053 Turquoise
054 - 061 Cyan
062 - 069 Blue
070 - 077 Lavender
078 - 085 Mauve
086 - 093 Magenta
094 - 101 Pink
102 - 109 Warm White
110 - 117 White
118 125 Cold White
126 127 Colour jumping stop
128 191 Colour jumping Speed slow->fast/Colour1->12
192 255 Colour fading Speed slow->fast/Colour1->12
3Ch mode1
Ch. Function Values Sub-group
1 Dimmer 000 - 255 0%-100% Dimmer
2
Strobe
000 - 255 Strobe Open
Strobe
006 - 010 Strobe Close
011 - 250 Strobe slow->fast<1Hz-20Hz
251 - 255 Strobe Open
3
Colour Macro
(override
RGBW)
000 - 005 Color OFF
Colour Macro
006 - 013 Red
014 - 021 Amber
022 - 029 Yellow Amber
030 - 037 Yellow
038 - 045 Green
046 - 053 Turquoise
054 - 061 Cyan
062 - 069 Blue
070 - 077 Lavender
078 - 085 Mauve
086 - 093 Magenta
094 - 101 Pink
102 - 109 Warm White
110 - 117 White
118 125 Cold White
126 127 Colour jumping stop
128 191 Colour jumping Speed slow->fast/Colour1->12
192 255 Colour fading Speed slow->fast/Colour1->12

3Ch mode2
Ch. Function Values Sub-group
1 Red 000 - 255 Red 0%-100% Red
2 Green 000 - 255 Green 0%-100% Green
3 Blue 000 - 255 Blue 0%-100% Blue
4Ch mode
Ch. Function Values Sub-group
1 Red 000 - 255 Red 0%-100% Red
2 Green 000 - 255 Green 0%-100% Green
3 Blue 000 - 255 Blue 0%-100% Blue
4 White 000 - 255 White 0%-100% Whtie
13Ch mode
Ch. Function Values Sub-group
1 Dimmer 000 - 255 Red 0%-100% Dimmer
2
Strobe
functions
000 - 005 Strobe open Green
006 - 010 Strobe closed
Multifunctional
-strobe
011 - 033 Plus Random, slow->fast
034 - 056 Ramp up Random, slow -> fast
057 - 079 Ramp down Random, slow -> fast
080 - 102 Random Strobe Effect, slow -> fast
103 - 127 Strobe Break Effect, 5s…..1s (Short burst with
break)
128 - 250 Strobe slow -> fast <1Hz - 20Hz
251 - 255 Strobe open
3 Red 000 - 255 Red 0%-100% Red
4 Green 000 - 255 Green 0%-100% Green
5 Blue 000 - 255 Blue 0%-100% Blue
6 White 000 - 255 White 0%-100% White
7
Colour Macro
(override
RGBW)
000 - 005 Color OFF
Colour Macro
006 - 013 Red
014 - 021 Amber
022 - 029 Yellow Amber
030 - 037 Yellow
038 - 045 Green
046 - 053 Turquoise
054 - 061 Cyan
062 - 069 Blue
070 - 077 Lavender
078 - 085 Mauve
086 - 093 Magenta
094 - 101 Pink
102 - 109 Warm White
110 - 117 White
118 125 Cold White
126 127 Colour jumping stop
128 191 Colour jumping Speed slow->fast/Colour1->12
192 255 Colour fading Speed slow->fast/Colour1->12
8 Rainbow
000 - 006 Rainbow off
Rainbow
effect
006 - 021 Rainbow1
022 - 037 Rainbow2
038 - 053 Rainbow3
054 - 069 Rainbow4
070 - 085 Rainbow5
086 - 101 Rainbow6
102 - 117 Rainbow7
118 - 133 Rainbow8
134 - 149 Rainbow9
150 - 165 Rainbow10
166 - 181 Rainbow11

182 - 197 Rainbow12
198 - 213 Rainbow13
214 - 229 Rainbow14
230 - 255 Rainbow15
9 Auto
000 - 005 No function
AUTO
Program
006 - 030 Auto Program1
031 - 055 Auto Program2
056 - 080 Auto Program3
081 - 105 Auto Program4
106 - 130 Auto Program5
131 - 155 Auto Program6
156 - 180 Auto Program7
181 - 205 Auto Program8
206 - 230 Auto Program9
231 - 255 Auto Program10
10 Speed 000 - 255 Auto program speed slow->fast Speed
11 Fade 000 - 255 Auto Fade Fade
12
Dimmer
Curve
000 - 005 No function
Set dimmer
curve
006 - 063 Linear Dimmer Curve
064 - 127 Exponential Dimmer Curve
128 - 191 Logarithmic Dimmer Curve
192 - 255 S-Curve Dimmer Curve
13
Device
settings
000 - 005 No function
Device
settings
006 - 063 Dimmer Response LED (Hold 3s)
064 - 127 Dimmer Response Halogen (Hold 5s)
128 - 191 Setting Fan High (Hold 3s)
192 - 255 Setting Fan Auto (Hold 3s)
16Ch mode
Ch. Function Values Sub-group
1 Red1 000 - 255 Red1 0%-100% Red1
2 Green1 000 - 255 Green1 0%-100% Green1
3 Blue1 000 - 255 Blue1 0%-100% Blue1
4 White1 000 - 255 White1 0%-100% Whtie1
5 Red2 000 - 255 Red2 0%-100% Red2
6 Green2 000 - 255 Green2 0%-100% Green2
7 Blue2 000 - 255 Blue2 0%-100% Blue2
8 White2 000 - 255 White2 0%-100% Whtie2
9 Red3 000 - 255 Red3 0%-100% Red3
10 Green3 000 - 255 Green3 0%-100% Green3
11 Blue3 000 - 255 Blue3 0%-100% Blue3
12 White3 000 - 255 White3 0%-100% Whtie3
13 Red4 000 - 255 Red4 0%-100% Red4
14 Green4 000 - 255 Green4 0%-100% Green4
15 Blue4 000 - 255 Blue4 0%-100% Blue4
16 White4 000 - 255 White4 0%-100% Whtie4
29Ch mode
Ch. Function Values Sub-group
1 Dimmer 000 - 255 Red 0%-100% Dimmer
2
Strobe
functions
000 - 005 Strobe open Green
006 - 010 Strobe closed
Multifunctional
-strobe
011 - 033 Plus Random, slow->fast
034 - 056 Ramp up Random, slow -> fast
057 - 079 Ramp down Random, slow -> fast
080 - 102 Random Strobe Effect, slow -> fast
103 - 127 Strobe Break Effect, 5s…..1s (Short burst with
break)

128 - 250 Strobe slow -> fast <1Hz - 20Hz
251 - 255 Strobe open
3 Red 000 - 255 Red 0%-100% Red
4 Green 000 - 255 Green 0%-100% Green
5 Blue 000 - 255 Blue 0%-100% Blue
6 White 000 - 255 White 0%-100% White
7
Colour Macro
(override
RGBW)
000 - 005 Color OFF
Colour Macro
006 - 013 Red
014 - 021 Amber
022 - 029 Yellow Amber
030 - 037 Yellow
038 - 045 Green
046 - 053 Turquoise
054 - 061 Cyan
062 - 069 Blue
070 - 077 Lavender
078 - 085 Mauve
086 - 093 Magenta
094 - 101 Pink
102 - 109 Warm White
110 - 117 White
118 125 Cold White
126 127 Colour jumping stop
128 191 Colour jumping Speed slow->fast/Colour1->12
192 255 Colour fading Speed slow->fast/Colour1->12
8 Rainbow
000 - 006 Rainbow off
Rainbow
effect
006 - 021 Rainbow1
022 - 037 Rainbow2
038 - 053 Rainbow3
054 - 069 Rainbow4
070 - 085 Rainbow5
086 - 101 Rainbow6
102 - 117 Rainbow7
118 - 133 Rainbow8
134 - 149 Rainbow9
150 - 165 Rainbow10
166 - 181 Rainbow11
182 - 197 Rainbow12
198 - 213 Rainbow13
214 - 229 Rainbow114
230 - 255 Rainbow15
9 Auto
000 - 005 No function
AUTO
Program
006 - 030 Auto Program1
031 - 055 Auto Program2
056 - 080 Auto Program3
081 - 105 Auto Program4
106 - 130 Auto Program5
131 - 155 Auto Program6
156 - 180 Auto Program7
181 - 205 Auto Program8
206 - 230 Auto Program9
231 - 255 Auto Program10
10 Speed 000 - 255 Auto program speed slow->fast Speed
11 Fade 000 - 255 Auto Fade Fade
12
Dimmer
Curve
000 - 005 No function
Set dimmer
curve
006 - 063 Linear Dimmer Curve
064 - 127 Exponential Dimmer Curve
128 - 191 Logarithmic Dimmer Curve
192 - 255 S-Curve Dimmer Curve
13
Device
settings
000 - 005 No function
Device
settings
006 - 063 Dimmer Response LED (Hold 3s)
064 - 127 Dimmer Response Halogen (Hold 5s)

128 - 191 Setting Fan High (Hold 3s)
192 - 255 Setting Fan Auto (Hold 3s)
14 Red1 000 - 255 Red1 0%-100% Red1
15 Green1 000 - 255 Green1 0%-100% Green1
16 Blue1 000 - 255 Blue1 0%-100% Blue1
17 White1 000 - 255 White1 0%-100% Whtie1
18 Red2 000 - 255 Red2 0%-100% Red2
19 Green2 000 - 255 Green2 0%-100% Green2
20 Blue2 000 - 255 Blue2 0%-100% Blue2
21 White2 000 - 255 White2 0%-100% Whtie2
22 Red3 000 - 255 Red3 0%-100% Red3
23 Green3 000 - 255 Green3 0%-100% Green3
24 Blue3 000 - 255 Blue3 0%-100% Blue3
25 White3 000 - 255 White3 0%-100% Whtie3
26 Red4 000 - 255 Red4 0%-100% Red4
27 Green4 000 - 255 Green4 0%-100% Green4
28 Blue4 000 - 255 Blue4 0%-100% Blue4
29 White4 000 - 255 White4 0%-100% Whtie4