Viking VDUI5240 User manual

Install / Use & Care
MANUAL
5 SERIES
Refrigerated Drawers
Tiroirs Réfrigérés
Gavetas Refrogeradas
VDUI5240
FR-D’installation/d’utilisation et d’entretien
ES-De instalación/operación y mantenimiento

2
NOTE
!CAUTION
Contents:
Safety information ...............................................................2
Unpacking your appliance ..................................................3
Warranty registration .....................................................3
Installing your appliance ......................................................4
Cabinet clearances .........................................................4
Leveling the appliance ....................................................4
Electrical connection ......................................................5
Installing the anti-tip device .................................................6
Product dimensions ............................................................8
Using your Electronic control ............................................10
Starting your appliance ..................................................10
Sleep mode ...................................................................10
Turning your appliance "ON" or "OFF" ..........................10
Adjusting the temperature .............................................11
Temperature mode ........................................................11
Controllock....................................................................11
Temperature sensor error codes ....................................11
Alarms ...........................................................................12
Door (drawer) ajar.....................................................12
Power failure ............................................................12
Temperature alarm ...................................................12
Vacationmode................................................................13
Care and cleaning .............................................................13
Energy saving tips ............................................................14
Obtaining service .............................................................14
Troubleshooting ................................................................15
Warranty ...........................................................................16
Important Safety Instructions
Warnings and safety instructions appearing in this guide
are not meant to cover all possible conditions and situa-
tions that may occur. Common sense, caution, and care
must be exercised when installing, maintaining, or operat-
ing this appliance.
Recognize Safety Symbols,
Words, and Labels.
CAUTION-Hazards or unsafe practices which could
result in personal injury or property / product damage.
NOTE-Important information to help assure a problem
free installation and operation.
CONTENTS
!WARNING
WARNING - You can be killed or seriously injured
if you do not follow these instructions.
!WARNING
State of California Proposition 65 Warning:
This product contains one or more chemicals known
to the State of California to cause cancer.
!WARNING
State of California Proposition 65 Warning:
This product contains one or more chemicals known
to the State of California to cause birth defects or
other reproductive harm..

3
NOTE
!CAUTION
!WARNING
XXXXXXXXXXXX
VIKING RANGE, LLC
GREENWOOD, MS 38930
UNPACKING YOUR APPLIANCE
EXCESSIVE WEIGHT HAZARD
Use two or more people to move product.
Failure to do so can result in personal injury.
Remove Interior Packaging
Your appliance has been packed for shipment with all parts
that could be damaged by movement securely fastened.
Remove internal packing materials and any tape holding in-
ternal components in place. The owners manual is shipped
inside the product in a plastic bag along with the warranty
registration card, and other accessory items.
Important
Keep your carton and packaging until your appliance has
been thoroughly inspected and found to be in good condi-
tion. If there is damage, the packaging will be needed as
proof of damage in transit. Afterwards please dispose of all
items responsibly.
Note to Customer
This merchandise was carefully packed and thoroughly
inspected before leaving our plant. Responsibility for its
safe delivery was assumed by the retailer upon acceptance
of the shipment. Claims for loss or damage sustained in
transit must be made to the retailer.
DO NOT RETURN DAMAGED MERCHANDISE TO THE
MANUFACTURER - FILE THE CLAIM WITH THE
RETAILER.
If the appliance was shipped, handled, or stored in other
than an upright position for any period of time, allow the ap-
pliance to sit upright for a period of at least 24 hours before
plugging in. This will assure oil returns to the compressor.
Plugging the appliance in immediately may cause damage
to internal parts.
It is important you send in your warranty registration card
immediately after taking delivery of your appliance or you
can register online at www.vikingrange.com
The following information will be
required when registering your
appliance.
Service Number
Rev. Letter
Serial Number
Date of Purchase
Dealer’s name and address
The service number and serial number can be found on
the serial plate which is located inside the cabinet on the
bottom of the liner toward the left side. Open the bottom
drawer to view it. See figure 1.
Warranty Registration
Online registration
available at
www.vikingrange.com
Figure 1
!WARNING
WARNING - Help Prevent Tragedies
Child entrapment and suffocation are not problems of
the past. Junked or abandoned refrigerators are still
dangerous - even if they sit out for "just a few hours".
If you are getting rid of your old refrigerator, please
follow the instructions below to help prevent acci-
dents.
Before you throw away your old refrigerator or
freezer:
• Take off the doors or remove the drawers.
• Leave the shelves in place so children may not
easily climb inside.
!WARNING
WARNING - Dispose of the plastic bags which can
be a suffocation hazard.

4
!CAUTION
Figure 2
Front Leveling
Legs
Front Grille,
keep this area
open.
Rear
Leveling
Legs
Select Location
The proper location will ensure peak performance of your
appliance. We recommend a location where the unit will
be out of direct sunlight and away from heat sources.
To ensure your product performs to specifications, the
recommended installation location temperature range is
from 55 to 100°F (13 to 38°C).
Cabinet Clearance
Ventilation is required from the bottom front of the
appliance. Keep this area open and clear of any
obstructions. Adjacent cabinets and counter top can be
installed around the appliance as long as the front grille
remains unobstructed.
Front Grille
Do not obstruct the front grille. The openings within
the front grille allow air to flow through the condenser
heat exchanger. Restrictions to this air flow will result in
increased energy usage and loss of cooling capacity. For
this reason it is important this area to not be obstructed and
the grille openings kept clean. Viking Range,LLC does not
recommend the use of a custom made grille as air flow may
be restricted. (See Figure 2).
Leveling Legs
Adjustable legs at the front and rear corners of the
appliance should be set so the unit is firmly positioned on
the floor and level from side to side and front to back. The
overall height of your appliance may be adjusted between
the minimum, 333⁄4" (85.7 cm), by turning the leveling leg in
(CW ↷) and the maximum, 343⁄4" (88.3 cm) by turning the
leveling leg out (CCW ↶).
To adjust the leveling legs, place the appliance on a solid
surface and protect the floor beneath the legs to avoid
scratching the floor. With the assistance of another person,
lean the appliance back to access the front leveling legs.
Raise or lower the legs to the required dimension by turning
the legs. Repeat this process for the rear by tilting the
appliance forward using caution. On a level surface check
the appliance for levelness and adjust accordingly.
The front grille screws may be loosened and the grille
adjusted to the desired height. When adjustment is
complete tighten the two front grille screws. (See Figure 5).
INSTALLING YOUR APPLIANCE

5
NOTE
Electrical Shock Hazard
• Do not use an extension cord with this appliance.
They can be hazardous and can degrade product
performance.
• This appliance should not, under any
circumstances, be installed to an un-grounded
electrical supply.
• Do not remove the grounding prong from the power
cord. (See Figure 3).
• Do not use an adapter. (See Figure 4).
• Do not splash or spray water from a hose on the
appliance. Doing so may cause an electrical shock,
which may result in severe injury or death.
!WARNING
Ground Fault Circuit Interrupters (GFCI) are prone to
nuisance tripping which will cause the appliance to shut
down. GFCI’s are generally not used on circuits with power
equipment that must run unattended for long periods of
time, unless required to meet local building codes and
ordinances.
Electrical Connection
A grounded 115 volt, 15 amp dedicated circuit is required.
This product is factory equipped with a power supply
cord that has a three-pronged, grounded plug. It must
be plugged into a mating grounding type receptacle
in accordance with the National Electrical Code and
applicable local codes and ordinances (see Figure 6). If the
circuit does not have a grounding type receptacle, it is the
responsibility and obligation of the customer to provide the
proper power supply. The third ground prong should not,
under any circumstances, be cut or removed.
Figure 6
Figure 5 Front grille screw
Front grille
INSTALLING YOUR APPLIANCE
Figure 3
Figure 4
Do not remove
ground prong

6
INSTALLING THE ANTI TIP DEVICE FOR FREESTANDING INSTALLATIONS
Step by step instructions for locating the po-
sition of the bracket:
1) Decide where you want to place the drawer refrigerator.
Slide it into place, being careful not to damage the floor,
leaving 1" (2.5 cm) of clearance from the rear wall to allow
room for the anti-tip bracket.
2) Raise the rear leveling legs approximately 1⁄4" (6 mm) to
allow engagement with the anti-tip bracket. Level the unit
by adjusting all the leveling legs as required. Turning the
leveling leg counterclockwise will raise the unit and clock-
wise will lower the unit.
3) Make sure the refrigerator is in the desired location, then
mark on the floor the rear and side corner of the cabinet
where the anti-tip bracket will be installed. If the installation
does not allow marking the rear corner of the cabinet, then
make temporary lines on the floor marking the front corner
of the cabinet, excluding the drawer. Slide the refrigerator
out of the way. From the temporary line extend the sidewall
line back 211⁄2" (54.6 cm) as shown in Figure 8.
4) Align the anti-tip bracket to the marks on the floor so
the side of the bracket lines up with the side of the cabinet
mark, and the "V" notches on the anti-tip bracket line up
with the end of the 211⁄2" (54.6 cm) line (Rear of cabinet
line).
5) Fasten the anti-tip bracket to the floor using the supplied
screw. (See Figure 8).
6) Slide the cabinet back into position, making sure the rear
cabinet leveling leg slides under the anti-tip bracket engag-
ing the slot.
Bottom View of
Refrigerated
Drawer Unit
Anti-Tip
Bracket Leveling Leg
Front of cabinet
211⁄2"
(54.6 cm)
Figure 7
!WARNING
• ALLAPPLIANCES CAN TIP
RESULTING IN INJURY.
• INSTALL THE ANTI-TIP
BRACKET PACKED WITH
THE APPLIANCE.
• FOLLOW THE
INSTRUCTIONS BELOW
Floor Mount Installation
The anti-tip bracket is to be located on the floor in the left
or right rear corner of the refrigerator drawer as shown in
Figure 7.
!CAUTION
NOTE
Any finished flooring should be protected with appropriate
material to avoid damage when moving the unit.
If installing on a concrete floor, concrete fasteners are
required, (not included with the anti-tip kit).
Anti-Tip Device
!WARNING
If your refrigerator is not located under a counter
top (free standing), you must use an anti-tip device
installed as per these instructions. If the refrigerator is
removed from its location for any reason, make sure
that the device is properly engaged with the anti-tip
bracket when you push the refrigerator back into the
original location. If the device is not properly engaged,
there is a risk of the refrigerator tipping over, with the
potential for property damage or personal injury.

7
INSTALLING THE ANTI TIP DEVICE FOR FREESTANDING INSTALLATIONS
211⁄2"
(54.6 cm)
"V" notches
in bracket
"V" notches
in bracket
Figure 8
Rear of cabinet line
Figure 8a
Side of cabinet line
Front of cabinet line
Screw
Rear Leveling leg

8
"A"
"B"
"C"
"D"
"E"
ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS
MODEL "A" "B" "C" "D" "E" "F" "G" "H"
VDUI5240 24"
(61 cm) **34" to 35" (86.4 cm to 88.9 cm) *237⁄8"
(60.7 cm) 333⁄4" to 343⁄4" (85.7 cm to 88.3 cm) 2323⁄32" (60.2 cm) 267⁄32" (66.6 cm) 395⁄32" (99.5 cm)
Figure 9
Figure 9a
* Depth dimension of rough-in opening may vary depending on each individual installation. To recess entire
drawer "F" dimension plus 1" (2.5 cm) for thickness of power cord plug is required.
** Minimum rough-in opening required is to be larger than the adjusted height of the cabinet.
PRODUCT DIMENSIONS
Figure 10
If necessary to gain clearance inside the rough-in
opening a hole can be cut through the adjacent
cabinet and the power cord routed through this
hole to a power outlet. Another way to increase
the available opening depth is to recess the power
outlet into the rear wall to gain the thickness of the
power cord plug. Not all recessed outlet boxes will
work for this application as they are too narrow,
but a recessed outlet box equivalent to Arlington
#DVFR1W is recommended for this application,
(see Figure 10).

9
"D"
"E"
"F"
"G"
"H"
Floor mount anti-tip bracket.
PRODUCT DATA
MODEL ELECTRICAL REQUIREMENTS # PRODUCT WEIGHT
VDUI5240 115V/60Hz/15A 130 lbs
(59 kg)
211⁄2"
(54.6 cm)
1"
(2.5 cm)
!
WARNING
Floor mount Anti-tip Bracket must be installed for
freestanding applications. Not required for built in
applications.
Figure 11
PRODUCT DIMENSIONS
# A grounded 15 amp dedicated circuit is required.
Follow all local building codes when installing
electrical and appliance.

10
Power Failure ALARM RESET
Temp
Minus
keypad
Temp
Plus
keypad
On/Off
keypad Display Area Lock
keypad System Status indicators
Figure 12
Electronic single zone control
Starting your appliance:
Plug the appliance power cord into a 115 volt wall outlet.
Your appliance is shipped from the factory in the "On"
position and will begin start-up of cooling as soon as power
is supplied. If the appliance does not start, confirm that the
wall outlet has power, and that the control is in the "On"
position, (See "Turning your appliance On and Off" below).
The control display is covered with a clear plastic film. This
film may be removed by carefully lifting the film at a corner.
On initial power up, the control display will indicate a
"Power Failure" alarm. This is a normal condition as
the appliance was powered-up at the factory for quality
inspection and then removed from power. A momentary
press of the "On/Off" keypad will reset this alarm condition.
(See Alarms section on page 12).
Turning your appliance ON and OFF:
If the appliance is "On", (and out of sleep mode) the
temperature will be shown in the display area of the control.
To turn the appliance "Off", press and hold the "On/Off"
keypad for 4-seconds. "OFF" will now be displayed on the
control.
To turn the appliance "On", press and hold the "On/Off"
keypad for 4-seconds.
Sleep mode:
If no keypads are pressed for 60 seconds, the display will
enter sleep mode to conserve power. The control panel
will go dark with the exception of the system status "OK"
indicator which will remain enabled. Alarm conditions will
wake the display, (see alarms on page 12).
To make the following changes to the control
settings (turning the appliance ON/OFF, adjusting the
temperature, and activating vacation mode), the control
must be awake.
The sleep mode can be disabled if you prefer to have the
display on continuously. Press and hold the "Lock" keypad
until the display goes past "Loc" and reads "nSL". To
enable the sleep mode, repeat the instruction, again going
past "Loc" until the display reads "SLP".
To wake the display press any keypad. A confirm tone will
sound, and the current storage compartment temperature
will be displayed.
USING YOUR ELECTRONIC CONTROL