Viking Storage Drawer User manual

F20411G EN (071610)
Viking Range Corporation
111 Front Street
Greenwood Mississippi 38930 USA
[phone]
For product information
call 1-888-VIKNG1 (845-4641)
or visit the Viking Web Site at
vikingrange.com
Viking Use/Installation Guide
Undercounter/Freestanding Refrigerated Drawer

3
UNDERCOUNTER CABINET CUTOUT
AA24” (61.0 cm)*
BBMin. 34-1/4” (87.0 cm)
Max. 35” (88.9 cm)
CC24” (61.0 cm)
Retain for Future Reference
IMPORTANT - PLEASE READ AND FOLLOW
•• Before beginning please read these instructions completely and carefully.
• Do not remove permanently affixed labels warnings or plates from the product. This may void the warranty.
• Please observe all local and national codes and ordinances.
• Please ensure that this product is properly grounded.
• The installer should leave these instructions with the consumer who should retain for local inspector’s use and for future reference.
TToo rreedduuccee tthhee rriisskk ooff ffiirree eelleeccttrriiccaall sshhoocckk oorr iinnjjuurryy wwhheenn uussiinngg yyoouurr rreeffrriiggeerraatteedd ddrraawweerr ffoollllooww bbaassiicc pprreeccaauuttiioonnss
iinncclluuddiinngg tthhee ffoolllloowwiinngg::
•FOR YOUR SAFETY•
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR
ANY OTHER APPLIANCE. THE FUMES CAN CREATE A FIRE HAZARD OR EXPLOSION.
IItt iiss yyoouurr rreessppoonnssiibbiilliittyy ttoo bbee ssuurree yyoouurr rreeffrriiggeerraatteedd ddrraawweerr iiss::
•located so the front is not blocked to restrict incoming or discharge air flow.
•properly leveled.
•located in a well ventilated area.
•connected to the proper kind of outlet with the correct electric supply and grounding. A 115 volt 60 Hz 15 amp
fused electrical supply is required. NNOOTTEE::Time delay fuse or circuit breaker is recommended.
•not used by anyone unable to operate it properly.
•used only for its intended purpose.
•properly maintained.
•SAVE THESE INSTRUCTIONS•
SUFFOCATION HAZARD
Re ove doors fro your old refrigerated drawer. Failure to do so can
result in child entrap ent, which can cause death or brain da age.
IMPORTANT: Child entrap ent and suffocation are not proble s of the
past. Junked or abandoned refrigerated drawers are still dangerous, even if
they will sit for “just a few days.” If you are getting rid of your refrigerated
drawer, please follow the instructions below to help prevent accidents.
BEFORE YOU THROW AWAY YOUR OLD REFRIGERATION PRODUCT:
•Take off the doors.
•Leave the shelves in place so that children may not easily climb inside.
2
B
C
A
*
*
Cabinet Cutout
*Optional: Cutout
for electrical outlet
can be placed in
adjacent cabinetry.
DANGER
WARNING
A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local la s, or local
ordinances.
• The required use of a GFI is normally related to the location of a receptacle with respect to any
significant sources of water or moisture.
• Viking Range Corporation will NOT warranty any problems resulting from GFI outlets which are not
installed properly or do not meet the requirements below.
If the use of a GFI is required it should be:
• Of the receptacle type (breaker type or portable type NOT recommended)
• Used with permanent wiring only (temporary or portable wiring NOT recommended)
• On a dedicated circuit (no other receptacles switches or loads in the circuit)
• Connected to a standard breaker of appropriate size (GFI breaker of the same size NOT recommended)
• Rated for Class A (5 mA +/- 1 mA trip current) as per UL 943 standard)
• In good condition and free from any loose-fitting gaskets (if applicable in outdoor situations)
• Protected from moisture (water steam high humidity) as much as reasonably possible
PROPER DISPOSAL OF YOUR OLD REFRIGERATION PRODUCT

54
SPECIFICATIONS/DIMENSIONS PROFESSIONAL
BBaassiicc EElleeccttrriicc DDaattaa
•115 VAC/60 Hz
•Maximum amps - 3.3
•Approximate Shipping Weight - 180 lbs. (81.8 kg)
30-3/4”
(78.1 cm)
Min. 34”
(86.4 cm)
to
Max. 34-3/4”
(88.3 cm)
with leveling
legs fully
extended.
23-7/8” (60.6 cm)
Front View Side View
26-7/8” (68.3 cm)
24-3/8” (61.9 cm)
22” (55.9 cm)
46-7/8” (119.0 cm)
48-3/4” (123.8 cm)

76
SPECIFICATIONS/DIMENSIONS DESIGNER
B
Ba as si ic c E El le ec ct tr ri ic c D Da at ta a
•115 VAC/60 Hz
•Maximum amps - 3.3
•Approximate shipping weight - 180 lbs. (81.8 kg)
30-3/4”
(78.1 cm)
Min. 34”
(86.4 cm)
to
Max. 34-3/4”
(88.3 cm)
with leveling
legs fully
extended.
23-7/8” (60.6 cm)
Front View Side View
26-7/8” (68.3 cm)
24-3/8” (61.9 cm)
22” (55.9 cm)
46-1/2” (118.1 cm)
48-3/4” (123.8 cm)

9
8
AREA REQUIREMENTS
Units Certified for Indoor Use - (black outer cabinet)
MUST BE INSTALLED IN AN AREA PROTECTED FROM THE ELEMENTS SUCH AS WIND RAIN WATER (SPRAY OR
DRIP).
1. Place unit so the front side will be completely unobstructed to provide proper air flow. The unit may be closed in
on the top and three sides but the front MMUUSSTT BBEEunobstructed for air circulation and proper operation.
Installation should be such that the cabinet can be moved for servicing if necessary.
2. Unit should be in a well ventilated area. Best results are obtained at temperatures between 55°F (12.8°C) and 80°F
(27°C) for built-in products and 55°F (12.8°C) and 90°F (32°C) for freestanding products.
3. Provisions for electricity and water connection should be determined before placing unit in proper place.
Units Certified for Outdoor Use - outdoor models contain a T after the base model number (ex. VURD144T) and
have a stainless steel outer cabinet.
MUST BE INSTALLED IN AN AREA PROTECTED FROM THE ELEMENTS SUCH AS WIND RAIN WATER (SPRAY OR
DRIP).
1. Place unit so the front side will be completely unobstructed to provide proper air flow. The unit may be closed in
on the top and three sides but the front MMUUSSTT BBEEunobstructed for air circulation and proper operation.
Installation should be such that the cabinet can be moved for servicing if necessary.
2. Unit should be in a well ventilated area with temperature above 40°F (4°C) and below 110°F (43°C).
3. Provisions for electricity should be determined before placing unit in proper place.
GENERAL INFORMATION
UUnnppaacckk
1. Remove banding from bottom of carton. Lift carton up and off of the unit.
2. Remove all tape and packaging material from the outside and inside of the cabinet.
3. Keep all carton packaging until your unit has been thoroughly inspected and found to be in good condition.
IIMMPPOORRTTAANNTT!!
Disconnect power source before adjusting leveling legs. A cabinet “anti-tip” device is mounted to the back of your
refrigerated drawer. If installation is a built-in undercounter application you do not need to apply this feature. If your
installation is a free-standing application with no counter top directly above the top of the refrigerated drawer you
must apply this feature to prevent the unit from tipping forward when the drawers are pulled out. the “anti-tip” device
is attached at the back of each cabinet. Please see installation instructions supplied with the “anti-tip” device.
WARNING
LEG LEVELER INSTALLATION
RReeaadd BBeeffoorree IInnssttaalllliinngg LLeegg LLeevveelleerrss
1. Four leveling legs are pre-installed in the base of the unit at the factory.
2. The unit should be leveled from front to back and side to side. If floor
conditions do not allow the unit to sit level adjust the leg levelers by turning
the required leg leveler counter-clockwise to increase the height and clockwise
to reduce the height.
WARNING
Do not lay unit on top side back or front. If unit is accidentally laid in
any position other than right side up then the unit must remain in the
upright position for at least 24 hours before plugging the unit in.
INSTALLING ANTI-TIP DEVICE
1. Push the unit against the wall so that the anti-tip bracket is flush to the wall adjacent to the back panel. Level
the unit with the leveling legs provided in the cabinet bottom. (See Leveling Legs on previous page.)
2. Using a pencil and the bracket as a template trace the bracket on the wall making sure two of the screw holes are
aligned with a stud in the wall.
3. Pull the unit away from the wall.
4. Remove the screws that connect the upper and lower sections of the anti-tip bracket.
5. Place the bracket on the wall and mark and drill 3/16” diameter Pilot holes for the provided 1/4” lag screws.
Mount the lower section ot the wall with the 1/4” lag screws.
6. Move the unit into place aligning the screw holes between the upper and lower brackets and secure with the
screws removed in Step 4.
A cabinet anti-tip device is mounted to the back of your refrigerated drawer unit. If your installation is a built-in
undercounter application with a countertop directly above the unit this item can be removed. It does not need to be
applied.
If your unit is a free-standing application with no countertop directly above the top of the unit you must apply this
feature to prevent the unit from tipping forward when the drawers are pulled out. The anti-tip device is installed on the
back of the unit. The anti-tip device reduces the chance of personal injury as well as property damage when properly
installed between the back of the unit and the adjacent wall. Please see the following instructions for installing the anti-
tip device.
CAUTION
FIGURE 4
Remove these screws to seperate
upper and lower sections of anti-tip
bracket.
To Refrigerated
Drawer Cabinet
To wall 1/4” Lag screws
into wall
FIGURE 3
Anti-Tip device

10 11
FULL OVERLAY PANEL INSTALLATION
Step #1
1. A #10 pan head wood screw should be used to properly secure the overlay panel. A total of 8 screws will be
needed.
2. Use only pan head screws.
3. Do not select a screw that is longer than the wood thickness of the screw locations.
4. Use recommended pilot holes for the frame material. (Use chart below.)
Gasket
5/16 Phillips Head Screws
Holding Drawer Front (8 total)
Step #2
R
Re em mo ov ve e D Dr ra aw we er r F Fr ro on nt ts s
(Note: The overlay panel may be installed without removing the drawer fronts from the drawer bodies but the full
drawer assembly is not as easy to handle as the drawer front alone.)
1. Remove drawer from unit. Begin by
pulling out the drawer. Locate the
drawer lock which can be found on the
outside of the cabinet slide (Figure 1).
Push the back of the drawer lock
forward and then down releasing the
drawer from the cabinet slide (Figure 2).
Repeat this on the opposite side of the
drawer. Lift the drawer up from the
slides at 90oto fully remove the drawer
from the cabinet (Figure 3).
2. Remove drawer fronts. Do this by
removing the 8 phillips screws and
washers securing the drawer front to
the drawer body. Mark lightly with an
erasable marker the position of the
stainless drawer liner where it is secured
to the stainless drawer before removing
screws.
3. Remove the gasket from the drawer
front. Do this by pulling the gasket out
of the channel that holds it to the
drawer front. This will expose the
clearance holes for mounting the
overlay panel.
PPiilloott HHoollee DDrriillll SSiizzeess ffoorr WWoooodd SSccrreewwss
WWoooodd SSccrreeww SSiizzee ##1100
WWoorrkk MMaatteerriiaallPilot Hole Size
HHaarrddwwoooodd3/32
SSooffttwwoooodd5/64
Figure 1 Figure 2
Figure 3
NOTE: Drawer divider not shown.
FULL OVERLAY PANEL INSTALLATION

12
FULL OVERLAY PANEL INSTALLATION (con’t)
Step #3
SSiizziinngg tthhee OOvveerrllaayy PPaanneell
Step #4
AAttttaacchhiinngg tthhee OOvveerrllaayy PPaanneell ttoo tthhee DDoooorr
1. Set the overlay panel on drawer front face and align edges. Clamp panel in position and mark pilot hole locations.
See Step #3 for nominal size and hole locations. Drill pilot holes (remove panel if necessary re-align and re-clamp
overlay to drawer face.)
2. Insert wood screws through clearance holes and tighten to secure overlay panel.
3. Reinstall gasket into channel. Make sure the corners are inserted fully.
Step #
RReeaattttaacchh DDrraawweerr FFrroonntt ttoo DDrraawweerr BBooddyy
Align mounting holes on drawer body with mounting holes on drawer front. Align the door liner to the front flanges by
using the erasable marker alignment lines that were applied prior to removing the door from the drawer. Reinstall
phillips head screws and washers. Snug down but do not tighten fully final adjustment of drawer front will be done
after reinstalling the drawer.
Step #6
RReeiinnssttaallll tthhee DDrraawweerr
1. Fully extend drawer slides and place drawer on slides. Be sure that drawer sits evenly on both sides.
2. Lock drawers into drawer slides. Push drawer locks down and then back to relock the drawer into the slide.
Step #7
AAddjjuusstt DDrraawweerr FFrroonntt
1. Adjust drawer front to achieve a 1/8” gap from the top of the drawer front to the top of the cabinet or (for bottom
drawers) 1/8” from the top of the drawer front to the bottom of the top drawer the drawer front should be centered
between the cabinet edges.
2. Fully tighten phillips head screws
23-5/8” (60.0 cm)
15-3/16”
(38.6 cm)
14-5/8”
(37.1 cm)
7-19/32”
(19.3 cm)
9/16”
(1.4 cm)
9/16” (1.4 cm)
11-13/16” (30.0 cm)
23-1/16” (58.6 cm)
13
FINAL PREPARATION
1. Some stainless steel parts may have a plastic protective wrap which must be peeled off. The interior of the unit should be
washed thoroughly with hot soapy water rinsed and wiped dry to remove film residue and any installation dust or debris
before being used. Solutions stronger than soap and water are rarely needed.
2. All stainless steel parts should be wiped with hot soapy water. If buildup occurs do not use steel wool abrasive cloths
cleaners or powders. If it is necessary to scrape stainless steel to remove encrusted materials soak with hot wet cloths to
loosen the material then use a wood or nylon scraper. Do not use a metal knife spatula or any other metal tool to scrape
stainless steel; scratches are almost impossible to remove.
ELECTRICAL CONNECTION
EElleeccttrriiccaall RReeqquuiirreemmeennttss
A 115 volt 60 Hz AC only 15 amp fused electrical supply is required. (A time delay
fuse or circuit breaker is recommended.) It is recommended that a separate circuit
serving only this appliance be provided.
••EELLEECCTTRRIICCAALL GGRROOUUNNDD IISS RREEQQUUIIRREEDD OONN TTHHIISS AAPPPPLLIIAANNCCEE..
••DDOO NNOOTT UUNNDDEERR AANNYY CCIIRRCCUUMMSSTTAANNCCEESS RREEMMOOVVEE TTHHEE PPOOWWEERR SSUUPPPPLLYY CCOORRDD
GGRROOUUNNDD PPLLUUGG..
••DDOO NNOOTT UUSSEE AANN EEXXTTEENNSSIIOONN CCOORRDD
RReeccoommmmeennddeedd GGrroouunnddiinngg MMeetthhooddss
For your personal safety this unit must be grounded. This appliance is equipped with a 7’ (2.1 m) power supply cord having a 3-
prong grounding plug. To minimize possible shock hazard the cord must be plugged into a mating 3-prong grounding type wall
receptacle grounded in accordance with the National Electrical Code and local codes and ordinances. If the circuit does not have
a grounding type receptacle it is the responsibility and obligation of the customer to exchange the existing receptacle in
accordance with the National Electrical Code and applicable local codes and ordinances. The third ground plug SHOULD NOT
under any circumstances be cut or removed. All UL listed refrigerated drawers are equipped with this type of plug.
Power Supply
with 3-prong
grounding plug
Grounding type wall
receptacle
ELECTRICAL SHOCK HAZARD
Failure to follow these instructions could result in fire or electrical
shock.
OPERATING INSTRUCTIONS
GGeenneerraall TTiippss aanndd SSuuggggeessttiioonnss
•After making a temperature adjustment allow at least 24 hours for your unit to reach a new temperature setting.
•The motor will start and stop often. It must do this to maintain the temperature setting.
•Unplug the unit before working on anything with the electrical system.
•Exercise caution when sweeping vacuuming or mopping near the front of the unit.
•Avoid leaning on the drawer fronts. You may bend the drawer slides or tip the unit.
WARNING

15
ON
OFF SET
WARMER
COLDER
˚F/C
PRESS AND HOLD
POWER FAILURE - Flashing Amber
HIGH/LOW TEMP - Red
PRESS ON/OFF - Reset
ALARMS OFF - Steady Amber
TruProtect System
38
˚
F
14
SETTING THE CONTROLS
The temperature of our drawer unit ranges from 32°F to 45°F (0°C to 7°C).
TruProtect™“Basic” Function “Quick” Reference
Function Function Access Control Confirmation/Comment
Turn Unit On & Off
Adjust Temperature Set-Point
Display “Actual” Temperature
Select °F or °C Display
Black-Out Mode
Sabbath Mode
TruProtect™ System
Door Ajar Alarm
High/Low Temp Alarm
Power Failure Alarm
Reset Alarms
Disable/Enable TruProtect™
Defrost
Pressing and holding the keypad for 5-seconds will turn the unit “ON” or “OFF”.
To adjust temperature set-point, touch keypad and current set-point will be displayed.
Use the or keypads to adjust set-point temperature.
Display represents “real-time” monitoring of the compartment’s stored wine and/or
contents. Some temperature fluctuation around your desired set-point is normal.
Pressing the keypad will toggle the display between Fahrenheit and Centigrade
temperature display.
Display automatically shuts off when door is closed.
°F/C
Press and hold the keypad while pressing the keypad four (4) times.
°F/C
System monitoring is automatically enabled unless system has been disabled. (See below).
For Door Ajar alarm, TruProtect™ must be Enabled, (See “Disable/Enable TruProtect™”,
described below).
Note: Alarm may occur when changing set-points in excess of 10°F, and/or high usage,
this is normal. TruProtect™ must be Enabled , (See “Disable/Enable TruProtect™”,
described below).
Note: Alarm will occur upon initial installation, since unit was run at factory to verify quality,
this is normal. TruProtect™ must be Enabled , (See “Disable/Enable TruProtect™”,
described below).
Close door to reset Door Ajar alarm. Press keypad to reset all other alarms.
Press and hold the keypad for 5-seconds to “disable” or “enable” TruProtect™ System.
No action required - Defrost will automatically occur as required. will be displayed during the defrost function.
Display will be blank when refrigeration system is off. Lights will still function, but will time-out 15 minutes after
each activation, if door is left open or display lighting is on, to prevent overheating.
“Set” will appear in display when in set-point mode. “SET” mode will automatically time-out in 10 seconds if no
keypad activity occurs, or you may exit “SET” mode by pressing the keypad a second time.
SET
Temperature variation in “compartment air”, above and below set-point, is a normal effect of refrigeration system
cycling on and off. Stored items will not experience the full temperature swing of the compartment air due to the
dampening effect of their thermal mass.
dE°F
=
In addition, the control panel is hidden when door is closed.
Display will flash four (4) times, then unit will enter Sabbath Mode. The display, audible alarms, LED and lights will
be disabled. Sabbath Mode will automatically time-out in 36 hours, or can be exited by repeating the enable keypad
routine.
LED displays steady green when TruProtect™ is enabled.
Audible alarm will sound 3-times every 30-seconds, LED will flash green.
Alarm will sound 6-times every minute and LED will flash red if product temperature excursions occur for a duration
outside acceptable limits.
LED will flash amber whenever power is interrupted to unit. No audible signal.
Note that although pressing the keypad will reset the alarms, the alarm will resume if the “alarm condition” still
exists.
LED displays steady green when alarm is enabled. LED displays steady amber when disabled.
ON
OFF
ON
OFF
SET
SET
SET
ON
OFF
WARMER COLDER
SA
38
˚
F
4
˚
C
38
˚
F
Function Function Access Control Confirmation/Comment
Turn Unit On & Off
Adjust Temperature Set-Point
Display “Actual” Temperature
Select °F or °C Display
Black-Out Mode
Sabbath Mode
TruProtect™ System
Door Ajar Alarm
High/Low Temp Alarm
Power Failure Alarm
Reset Alarms
Disable/Enable TruProtect™
Defrost
Pressing and holding the keypad for 5-seconds will turn the unit “ON” or “OFF”.
To adjust temperature set-point, touch keypad and current set-point will be displayed.
Use the or keypads to adjust set-point temperature.
Display represents “real-time” monitoring of the compartment’s stored wine and/or
contents. Some temperature fluctuation around your desired set-point is normal.
Pressing the keypad will toggle the display between Fahrenheit and Centigrade
temperature display.
Display automatically shuts off when door is closed.
°F/C
Press and hold the keypad while pressing the keypad four (4) times.
°F/C
System monitoring is automatically enabled unless system has been disabled. (See below).
For Door Ajar alarm, TruProtect™ must be Enabled, (See “Disable/Enable TruProtect™”,
described below).
Note: Alarm may occur when changing set-points in excess of 10°F, and/or high usage,
this is normal. TruProtect™ must be Enabled , (See “Disable/Enable TruProtect™”,
described below).
Note: Alarm will occur upon initial installation, since unit was run at factory to verify quality,
this is normal. TruProtect™ must be Enabled , (See “Disable/Enable TruProtect™”,
described below).
Close door to reset Door Ajar alarm. Press keypad to reset all other alarms.
Press and hold the keypad for 5-seconds to “disable” or “enable” TruProtect™ System.
No action required - Defrost will automatically occur as required. will be displayed during the defrost function.
Display will be blank when refrigeration system is off. Lights will still function, but will time-out 15 minutes after
each activation, if door is left open or display lighting is on, to prevent overheating.
“Set” will appear in display when in set-point mode. “SET” mode will automatically time-out in 10 seconds if no
keypad activity occurs, or you may exit “SET” mode by pressing the keypad a second time.
SET
Temperature variation in “compartment air”, above and below set-point, is a normal effect of refrigeration system
cycling on and off. Stored items will not experience the full temperature swing of the compartment air due to the
dampening effect of their thermal mass.
dE°F
=
In addition, the control panel is hidden when door is closed.
Display will flash four (4) times, then unit will enter Sabbath Mode. The display, audible alarms, LED and lights will
be disabled. Sabbath Mode will automatically time-out in 36 hours, or can be exited by repeating the enable keypad
routine.
LED displays steady green when TruProtect™ is enabled.
Audible alarm will sound 3-times every 30-seconds, LED will flash green.
Alarm will sound 6-times every minute and LED will flash red if product temperature excursions occur for a duration
outside acceptable limits.
LED will flash amber whenever power is interrupted to unit. No audible signal.
Note that although pressing the keypad will reset the alarms, the alarm will resume if the “alarm condition” still
exists.
LED displays steady green when alarm is enabled. LED displays steady amber when disabled.
ON
OFF
ON
OFF
SET
SET
SET
ON
OFF
WARMER COLDER
SA
38
˚
F
4
˚
C
38
˚
F

17
LED LIGHT REPLACEMENT
Never pour liquids directly onto light asse bly.
ELECTRICAL SHOCK HAZARD
Failure to disconnect the power cord when changing
the light bulb ay result in electrical shock.
INTERIOR LIGHT
1. Unplug unit.
2. Remove drawers. (This is not required to remove the light but will provide better access). See Figures 1 through 3 in
Full Overlay Panel Installation on page 6.
3. Remove old lights. Use 2 small thin bladed screwdrivers or putty knives to press in the locking tabs on the lens
housing. (Figures 4 and 5). With the locking tabs depressed pull downward (Figure 6) the light housing will pop
free. Disconnect the wire lead by pulling straight out from the connector. Connect wire lead to new light and re-
install into metal housing. The light will only fit in the housing with the locator tabs pointing to the front of the unit.
4. Re-install drawers.
5. Plug in unit.
Figure 4 Figure 5 Figure 6
16
ENERGY SAVING TIPS
The followin su estions will minimize the cost of operatin your refri eration appliance.
1. Do not install your appliance next to a hot appliance (cooker dishwasher etc.) heating air duct or other heat sources.
2. Install product out of direct sunlight.
3. Assure the toe grille vents at front of unit beneath door are not obstructed. Keep toe grille vents clean to allow
ventilation for the refrigeration system to expel heat.
4. Plug your appliance into a dedicated power circuit. (Not shared with other appliances.)
5. When initially loading your new product or whenever large quantities of warm contents are placed within refrigerated
storage compartment minimize door openings for the next 12 hours to allow contents to pull down to compartment
set- point temperature.
6. Maintaining a relatively full storage compartment will require less appliance run-time than an empty compartment.
7. Assure door closing is not obstructed by contents stored in your appliance.
8. Allow hot items to reach room temperature before placing in product.
9. Minimize door openings and duration of door openings.
10. Use the warmest temperature control set-point that meets your personal preference and provides the proper storage
for your stored contents.
11. Minimize use of display lighting option on glass door products (light stays on with door closed).
12. When on vacation or away from home for extended periods set the appliance to warmest acceptable temperature for
the stored contents.
13. Set the control to the “OFF” position if cleaning the unit requires the door to be open for an extended period of time.
14. Annually clean condenser heat exchange coil located in machine compartment underneath unit (see Cleaning and
Maintenance section).
WARNING CAUTION

1918
TROUBLESHOOTING CHART
Problem Possible Cause Solution
Odor in cabinet Unit interior needs cleaning Clean inside of unit
Noisy operation Unit not level Adjust leveling legs
Unit vibrates Unit not level Adjust leveling legs
Weak floor Rebuild floor or move to a different location
Interior lighting not working LED light burned out Replace LED light
No power at outlet Test outlet with lamp
Appliance will not run Control panel tuned “OFF” Turn unit on with on/off pad on control panel
Power cord not plugged into power
source
Plug unit into power source
House fuse blown Reset house fuse
Appliance runs too long Prolonged door openings Reduce number and/or duration of openings
Control panel set too cold Raise temperature of unit via control panel
Condenser needs cleaning Clean condenser
Moisture collects inside
of unit
Too many door openings Reduce number of door openings
Prolonged door openings Reduce number of door openings
Hot humid weather increases
condensation
Move unit to cooler location
As humidity decreases moisture will disappear
Moisture collects on outside
surface of unit
Hot humid weather increases Move unit to cooler location
Control improperly set Reset to slightly warmer temperature
Interior too hot/too cold Control improperly set Reset control to desired temperature
Faulty thermometer Recheck with second thermometer
CLEANING AND MAINTENANCE
Any piece of equipment works better and lasts longer when maintained properly and kept clean.
Condenser
The condenser underneath the cabinet does not require frequent cleaning; however satisfactory cooling depends on
adequate ventilation over this heat exchanger. It is recommended to annually clean the condenser by vacuuming and
brushing. To access the condenser the unit must be pulled out from the installation and the lower machine compartment
access cover removed.
Be sure that nothing obstructs the required air flow openings in front of the cabinet. At least once or twice a year brush or
vacuum lint and dirt from the front grille area.
Cabinet
The cabinet can be washed with mild soap and water and thoroughly rinsed with clear water. Never use abrasive scouring
powders.
Interior
Wash interior compartment with mild soap and water. Do not use abrasive powder solvent polish cleaner or undiluted
detergent.
Stainless Steel Parts
All stainless steel parts should be wiped regularly with hot soapy water. Use a liquid cleaner designed for stainless steel when
soapy water will not do the job. Do not use steel wool abrasive cloths cleansers or powders. Do not permit citrus or tomato
juice to remain on stainless steel surfaces as citric acid will permanently discolor stainless steel.
Brass Parts
CCAAUUTTIIOONN:: All brass parts are coated with an epoxy coating. DO NOT USE BRASS OR ABRASIVE CLEANERS ON THE
BRASS PARTS. All brass parts should be wiped regularly with hot soapy water. When hot soapy water will not do the job
use every day non-abrasive household cleaners.
Door Gasket
The vinyl gasket may be cleaned with mild soap and water a baking soda and water solution or a mild scouring powder.
Painted Surfaces
Wash with warm soapy water. DO NOT USE steel wool abrasive cleansers ammonia acids or commercial oven cleaners
which may damage the finish.
WARNING
Disconnect the power cord before re oving the access cover.

20 21
ON
OFF SET
WARMER
COLDER
˚F/C
PRESS AND HOLD
POWER FAILURE - Flashing Amber
HIGH/LOW TEMP - Red
PRESS ON/OFF - Reset
ALARMS OFF - Steady Amber
TruProtect System
38
˚
F
TruProtect™“Advanced” Function “Quick” Reference
SERVICE DIAGNOSTICS
“Enter” and “Exit” Service Diagnostics mode by pressing and holding the keypad
while pressing the keypad 4-times within 5-seconds. Service Diagnostics mode
also will automatically exit after 5-minutes of no keypad entry.
Function Function Access Control Confirmation/Comment
Show Room Mode
Service Diagnostics
Enable the Show Room Mode by pressing and holding the keypad while
performing a “Power On Reset”, (POR), i.e. - disconnect and reconnect the power
supply to unit. Exit Show Room Mode by initiating a POR only.
ON
OFF
Display Error Code Reference:
The microprocessor in the control continually monitors critical refrigeration system
components for proper operation. If component parameters exceed normal operating
specifications, the display will automatically flash the respective error code as follows:
Compressor fault, (high/low amps).
Condenser fan motor fault, (high/low amps).
Evaporator thermistor “sensor B” fault, (out-of-range).
Display thermistor “sensor A” fault, (out-of-range).
Power line fluctuations may cause an error code to be displayed with no product fault.
Therefore, the first time an error code appears, please clear the code by holding and
pressing 4 times. If the product is at fault, the error code will appear again, and you
should contact your Dealer or Viking Customer Service to schedule service by a
qualified technician.
ON
OFF
E1
E2
E3
E4
Show Room Mode will disable the refrigerator system and fans while allowing the internal lights, display and user
interface panel to function. Lights will time out after 15-minutes of continuous on-time while in Show Room Mode
as a safety feature. The 15-minute light-on time can be reactivated by closing and opening the door or by pressing
the keypad.
LIGHT
Service Diagnostics Mode enables service technicians to identify the firmware and software versions, test status of
“model specific” system components and sensors and change state of components where applicable, (i.e. - compressor
on/off, etc...). While in Service Diagnostics Mode, tests are incrememed by pressing the keypad and specific
component state can be changed to “on” and “off” by pressing the and keypads respectively. The
following component tests are available: Available Status Indicators
Test # Component Description OK Off/Open On/Shorted
0 Temp Sensor A
1 Temp Sensor B
2 Compressor
3 Interior/Ice Maker Fan
4 Reverse Gas Solenoid
5 Condenser Fan
6 Mullion Heater
7 Door A Sense
8 Door B Sense
9 Door C Sense
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
Note: Must use magnet to change state of Door C Sense.
0-
1-
00
10
20
30
40
50
60
70
80
90
01
11
21
31
41
51
61
71
81
91
PRES S AND HOLD
magnet sense area
ON
OFF SET
SET
SET
WARMER COLDER
WARMER
COLDER
38
˚
F
“Enter” and “Exit” Service Diagnostics mode by pressing and holding the keypad
while pressing the keypad 4-times within 5-seconds. Service Diagnostics mode
also will automatically exit after 5-minutes of no keypad entry.
Function Function Access Control Confirmation/Comment
Show Room Mode
Service Diagnostics
Enable the Show Room Mode by pressing and holding the keypad while
performing a “Power On Reset”, (POR), i.e. - disconnect and reconnect the power
supply to unit. Exit Show Room Mode by initiating a POR only.
ON
OFF
Display Error Code Reference:
The microprocessor in the control continually monitors critical refrigeration system
components for proper operation. If component parameters exceed normal operating
specifications, the display will automatically flash the respective error code as follows:
Compressor fault, (high/low amps).
Condenser fan motor fault, (high/low amps).
Evaporator thermistor “sensor B” fault, (out-of-range).
Display thermistor “sensor A” fault, (out-of-range).
Power line fluctuations may cause an error code to be displayed with no product fault.
Therefore, the first time an error code appears, please clear the code by holding and
pressing 4 times. If the product is at fault, the error code will appear again, and you
should contact your Dealer or Viking Customer Service to schedule service by a
qualified technician.
ON
OFF
E1
E2
E3
E4
Show Room Mode will disable the refrigerator system and fans while allowing the internal lights, display and user
interface panel to function. Lights will time out after 15-minutes of continuous on-time while in Show Room Mode
as a safety feature. The 15-minute light-on time can be reactivated by closing and opening the door or by pressing
the keypad.
LIGHT
Service Diagnostics Mode enables service technicians to identify the firmware and software versions, test status of
“model specific” system components and sensors and change state of components where applicable, (i.e. - compressor
on/off, etc...). While in Service Diagnostics Mode, tests are incrememed by pressing the keypad and specific
component state can be changed to “on” and “off” by pressing the and keypads respectively. The
following component tests are available: Available Status Indicators
Test # Component Description OK Off/Open On/Shorted
0 Temp Sensor A
1 Temp Sensor B
2 Compressor
3 Interior/Ice Maker Fan
4 Reverse Gas Solenoid
5 Condenser Fan
6 Mullion Heater
7 Door A Sense
8 Door B Sense
9 Door C Sense
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
Note: Must use magnet to change state of Door C Sense.
0-
1-
00
10
20
30
40
50
60
70
80
90
01
11
21
31
41
51
61
71
81
91
PRES S AND HOLD
magnet sense area
ON
OFF SET
SET
SET
WARMER COLDER
WARMER
COLDER
38
˚
F

22 23
UNDERCOUNTER/FREESTANDING REFRIGERATED DRAWER WARRANTY
(Units certified for Indoor Use)
T
TW WO O Y YE EA AR R F FU UL LL L W WA AR RR RA AN NT TY Y
Undercounter/freestanding refrigerated drawers and all of their components and accessories except as detailed below* are warranted to be free from defects in material or
workmanship under normal household use for a period of two (2) years from the date of original retail purchase. Viking Range Corporation warrantor agrees to repair or
replace at its option any part which fails or is found to be defective during the warranty period
*Painted and decorative items are warranted to be free from defective materials or workmanship for a period of ninety (90) days from the date of original retail purchase.
ANY DEFECTS MUST BE REPORTED TO THE SELLING DEALER WITHIN NINETY (90) DAYS FROM DATE OF ORIGINAL RETAIL PURCHASE.
SSIIXX YYEEAARR FFUULLLL WWAARRRRAANNTTYY
Any sealed refrigeration system component as listed below is warranted to be free from defective materials or workmanship in normal household use during the third
through the sixth year from the date of original retail purchase. Viking Range Corporation warrantor agrees to repair or replace at its option any part which fails or is found
to be defective during the warranty period.
SSeeaalleedd RReeffrriiggeerraattiioonn SSyysstteemm CCoommppoonneennttss::Compressor Evaporator Condenser Connecting Tubing Dryer/Strainer
TTWWEELLVVEE YYEEAARR LLIIMMIITTEEDD WWAARRRRAANNTTYY
Any sealed refrigeration system component as listed above which fails due to defective materials or workmanship in normal household use during the seventh through the
twelfth year from the date of original retail purchase will be repaired or replaced free of charge for the part itself with the owner paying all other costs including labor.
NNIINNEETTYY ((9900)) DDAAYY RREESSIIDDEENNTTIIAALL PPLLUUSS WWAARRRRAANNTTYY This warranty applies to applications where use of the product extends beyond normal residential use.
Examples are but not limited to bed and breakfasts fire stations private clubs churches etc. This warranty excludes all commercial locations such as restaurants
food service locations and institutional food service locations.
This warranty extends to the original purchaser of the product warranted hereunder and to each transferee owner of the product during the term of the warranty.
This warranty shall apply to products purchased and located in the United States and Canada. Products must be purchased in the country where service is requested.
Warranty labor shall be performed by an authorized Viking Range Corporation service agency or representative. Warranty shall not apply to damage resulting from abuse
accident natural disaster loss of electrical power to the product for any reason alteration improper installation improper operation or repair or service to the product by
anyone other than an authorized Viking Range Corporation service agency or representative. Warranty shall not apply to damage resulting from indoor units being used in
outdoor situations. This warranty does not apply to commercial usage. Warrantor is not responsible for consequential or incidental damage whether arising out of breach of
warranty breach of contract or otherwise. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or
exclusion may not apply to you.
Owner shall be responsible for proper installation providing normal care and maintenance providing proof of purchase upon request and making the appliance reasonably
accessible for service. If the product or one of its component parts contains a defect or malfunction during the warranty period after a reasonable number of attempts by
the warrantor to remedy the defects or malfunctions the owner is entitled to either a refund or replacement of the product or its component part or parts. Replacement of a
component part includes its free installation. Warrantor’s liability on any claim of any kind with respect to the goods or services covered hereunder shall in no case exceed
the price of the goods or service or part there of which gives rise to the claim.
WWAARRRRAANNTTYY SSEERRVVIICCEE::Under the terms of this warranty service must be performed by a factory authorized Viking Range Corporation service agent or representative.
Service will be provided during normal business hours and labor performed at overtime or premium rates shall not be covered by this warranty. To obtain warranty service
contact the dealer from whom the product was purchased an authorized Viking Range Corporation service agent or Viking Range Corporation. Provide model and serial
number and date of original purchase. For the name of your nearest authorized Viking Range Corporation service agency call the dealer from whom the product was
purchased or Viking Range Corporation. IIMMPPOORRTTAANNTT::Retain proof of original purchase to establish warranty period.
The return of the Owner Registration Card is not a condition of warranty coverage. You however should return the Owner Registration Card so that Viking Range
Corporation can contact you should any question of safety arise which could affect you.
Any implied warranties of merchantability and fitness applicable to the above described undercounter refrigerated drawer are limited in duration to the period of coverage of
the applicable express written limited warranties set forth above. Some jurisdictions do not allow limitations on how long an implied warranty lasts so the above limitation
may not apply to you. This warranty gives you specific rights and you may also have other rights which may vary from jurisdiction to jurisdiction.
SERVICE INFORMATION
If service is required call your dealer or authorized service agency. The name of the authorized service agency can be
obtained from the dealer or distributor in your area.
Have the following information readily available.
• Model number
• Serial number
• Date purchased
• Name of dealer from whom purchased
Clearly describe the problem that you are having. If you are unable to obtain the name of an authorized service agency
or if you continue to have service problems contact Viking Range Corporation at 1-888-VIKING1 (845-4641) or write
to:
VIKING RANGE CORPORATION
PREFERRED SERVICE
1803 Hwy 82W
Greenwood, Mississippi 38930 USA
Record the following information indicated below. You will need it if service is ever required. The serial number and
model number for your refrigerated drawer is located on the front of the unit at the base of the door frame.
Model Number Serial Number
Date of Purchase Date Installed
Dealer’s Name
Address
IIff sseerrvviiccee rreeqquuiirreess iinnssttaallllaattiioonn ooff ppaarrttss uussee oonnllyy aauutthhoorriizzeedd ppaarrttss ttoo eennssuurree pprrootteeccttiioonn uunnddeerr tthhee wwaarrrraannttyy..
TThhiiss mmaannuuaall sshhoouulldd rreemmaaiinn wwiitthh tthhee rreeffrriiggeerraatteedd ddrraawweerr ffoorr ffuuttuurree rreeffeerreennccee..
ENERGY SAVING TIPS
•Reduce drawer openings.
•Close the drawer as soon as you can.
•Keep the condenser coils on bottom of the unit clean. (See “Cleaning and Maintenance”.)
•Adjust the temperature control to a warmer setting when practical.
•Do not put hot foods in the unit.
•Install unit away from the stove or other heat sources.
Specifications subject to change without notice.

2524
UUNNDDEERRCCOOUUNNTTEERR//FFRREEEESSTTAANNDDIINNGG RREEFFRRIIGGEERRAATTEEDD DDRRAAWWEERR WWAARRRRAANNTTYY
(Units certified for Outdoor Use)
OONNEE YYEEAARR FFUULLLL WWAARRRRAANNTTYY
Built-in/freestanding undercounter refrigerated drawers and all of their components and accessories except as detailed below* are warranted to be free from defects in
material or workmanship under normal household use for a period of one (1) year from the date of original retail purchase. Viking Range Corporation warrantor agrees to
repair or replace at its option any part which fails or is found to be defective during the warranty period.
*Painted and decorative items are warranted to be free from defective materials or workmanship for a period of ninety (90) days from the date of original retail purchase.
ANY DEFECTS MUST BE REPORTED TO THE SELLING DEALER WITHIN NINETY (90) DAYS FROM DATE OF ORIGINAL RETAIL PURCHASE.
FFIIVVEE YYEEAARR LLIIMMIITTEEDD WWAARRRRAANNTTYY
Any sealed refrigeration system component as listed below is warranted to be free from defective materials or workmanship in normal household use during the second
through the fifth year from the date of original retail purchase. Viking Range Corporation warrantor agrees to repair or replace at its option any part which fails or is found
to be defective during the warranty period.
SSeeaalleedd RReeffrriiggeerraattiioonn SSyysstteemm CCoommppoonneennttss::Compressor Evaporator Condenser Connecting Tubing Dryer/Strainer
It is recommended that in temperatures above 100oF (37.8oC) and below 40oF (4.4oC) the unit be shut off. The normal operating range for the unit is between 60oF (15.6oF)
and 100oF (37.8oC).
N
NI IN NE ET TY Y ( (9 90 0) ) D DA AY Y R RE ES SI ID DE EN NT TI IA AL L P PL LU US S W WA AR RR RA AN NT TY Y This warranty applies to applications where use of the product extends beyond normal residential use.
Examples are but not limited to bed and breakfasts fire stations private clubs churches etc. This warranty excludes all commercial locations such as restaurants
food service locations and institutional food service locations.
This warranty extends to the original purchaser of the product warranted hereunder and to each transferee owner of the product during the term of the warranty.
This warranty shall apply to products purchased and located in the United States and Canada. Products must be purchased in the country where service is requested.
Warranty labor shall be performed by an authorized Viking Range Corporation service agency or representative. Warranty shall not apply to damage resulting from abuse
accident natural disaster loss of electrical power to the product for any reason alteration improper installation improper operation or repair or service to the product by
anyone other than an authorized Viking Range Corporation service agency or representative. Warranty shall not apply to damage resulting from indoor units being used in
outdoor situations. This warranty does not apply to commercial usage. Warrantor is not responsible for consequential or incidental damage whether arising out of breach
of warranty breach of contract or otherwise. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or
exclusion may not apply to you.
Owner shall be responsible for proper installation providing normal care and maintenance providing proof of purchase upon request and making the appliance reasonably
accessible for service. If the product or one of its component parts contains a defect or malfunction during the warranty period after a reasonable number of attempts by
the warrantor to remedy the defects or malfunctions the owner is entitled to either a refund or replacement of the product or its component part or parts. Replacement of a
component part includes its free installation. Warrantor’s liability on any claim of any kind with respect to the goods or services covered hereunder shall in no case exceed
the price of the goods or service or part there of which gives rise to the claim.
WWAARRRRAANNTTYY SSEERRVVIICCEE::Under the terms of this warranty service must be performed by a factory authorized Viking Range Corporation service agent or representative.
Service will be provided during normal business hours and labor performed at overtime or premium rates shall not be covered by this warranty. To obtain warranty service
contact the dealer from whom the product was purchased an authorized Viking Range Corporation service agent or Viking Range Corporation. Provide model and serial
number and date of original purchase. For the name of your nearest authorized Viking Range Corporation service agency call the dealer from whom the product was
purchased or Viking Range Corporation. IIMMPPOORRTTAANNTT::Retain proof of original purchase to establish warranty period.
The return of the Owner Registration Card is not a condition of warranty coverage. You however should return the Owner Registration Card so that Viking Range
Corporation can contact you should any question of safety arise which could affect you.
Any implied warranties of merchantability and fitness applicable to the above described undercounter refrigerated beverage center are limited in duration to the period of
coverage of the applicable express written limited warranties set forth above. Some jurisdictions do not allow limitations on how long an implied warranty lasts so the above
limitation may not apply to you. This warranty gives you specific rights and you may also have other rights which may vary from jurisdiction to jurisdiction.
Specifications subject to change without notice.

2726