Vision Drive HD BLACK BOX VD-8000HD User manual

Connect the bracket and the unit
2
3
4
5
6
7
8
1
Installation User Manual
www.visiondrive.co.kr
Ver. VD-8000HDS 1.0 E
Do not disassemble or remodel this product as it can cause an electric shock.
Only use adaptors with the appropriate specifications.
Do not disassemble the product.
When installing the device to your vehicle, follow all the procedures and make sure the
mount is secure.
Unclean surfaces will weaken the adhesive strength and can damage the product if it
drops due to weak adhesion.
This product is not waterproof. Do not allow liquids and impurities to enter the product.
Where the product is wired to the power supply of the vehicle directly or if the cigar jack
is connected to the power supply while the engine is off, make sure to disconnect the
device to prevent battery drain on your vehicle.
Do not use chemicals or detergents to clean the device. This can result in malfunctioning
of the product.
Caution
!
Connect the attachment bracket with the main unit and push it to the
direction 1 to secure the lock to hear the click sound.
Connect the external option camera and the
main unit
Insert SD card into the unit
Connect cable and attach on windshield
Connect the jack of Optional Infra - Red second camera to the “cam”
port of the main unit. (When connected to the main unit while the
main unit is on, the system will reboot to register the option camera
and initialize 2 channel recording mode.)
Clean the area on the windshield where the unit will be installed.
For the placement of the unit, it is better to place the unit closer to the
center of the vehicle.
Connect to power source to turn on the unit
Insert the cigarette jack into an appropriate outlet then turn on the engine.
Check LED lamps
The REC lamp is blue when it is recording. It is blue when it is recording a
(NORMAL) file and red when recording an (EVENT) file after an impact or if
the SHOT button has been pressed.
The GPS lamp is red when the GPS signal is not received and blue when it is
received. The GPS connection may take a couple of seconds to several
minutes, depending on the location of your vehicle.
Adjust the camera angle
Move the camera top to bottom to fix it to a recordable position while
checking the LCD
Arranging wires
Use the enclosed wire holders to organize the cable line.
2011.11.01 12:00:00
1
2

2. Normal and Event recording
• System makes Normal files with power on and stores it in the NORMAL folder of the SD card.
• When registering an impact, the system alarms and record an Event file in the EVENT folder
of the SD card.
3. Manual (Event) recording
• When the [SHOT] button is pressed, the alarm will sound and the recorded data will be saved in
the (EVENT) folder.
4. Playback of the recorded videos on LCD
• [PLAY] button starts the latest videos files.
• [SHOT] button changes the videos according to time sequences.
• Date and time data shows on the bottom of LCD.
(#There is no time sign on LCD when no GPS data registered.)
• You can enlarge the video on LCD whilst the video is being played by clicking the [PLAY] button.
[PLAY] buttons can enlarge x2 and x4 times and return to original size.
• A longer press of [PLAY] button for more than 3 seconds will make the system return to recording
mode followed by an announcement of audio recording status.
5. Voice Recording
• During the system records, when the [SHOT] button is pressed and held for more than 3 seconds,
the voice notification will announce that the voice recording will initiate and the voice recording will
start or stop.
• The initial audio recording setting can be changed in the analysis program.
6. Parking Surveillance Mode
• To enter into the “Parking Mode” recording, push and hold the [PLAY] button for more than 3 seconds
when the system is recording.
• The system automatically rearranges its impact sensing sensitivity to most sensitive in order to register
the slightest impacts.
• While no impacts, the system records 4 frames/second to save the SD space and return to normal full
frame recording mode making an EVENT file when it receives a certain impact to car. After making an
EVENT file, it returns to 4 frame recording mode again.
• No audio is recorded while parking mode is on.
• In parking mode, the system repeats “Parking mode is on” every 2 minutes.
• To return to normal (driving) recording mode, press and hold the [PLAY] button for more than 3 seconds
to hear the “Driving mode on” announcement.
7. Disconnecting the SD card
• If you eject the SD card while the product is on, the recorded data may be damaged.
Make sure the main power is completely off and the device is fully powered off (no indicator lights
are on) before removing the SD card from the product.
8. PC Analysis Program Use
• Insert the SD into your PC and run VDAnalyzer.exe to start video analysis.
• Please use a SDHC compatible USB adapter when using a USB adapter to read the SD card.
• VDAnalyzer.exe runs only when the SD card is in PC and the default password is “12345678”.
*** Please refer to the manual for further information ***
*** Please wait for complete power off before taking the SD off. ***
1. Viewing recording videos on LCD (2ch mode)
• [VIEW] button press for LCD operation
Main Camera View =>Option Camera View =>LCD Off =>Min Camera view
(1ch mode does not have Option Camera view sequence.)
1 ch. Mode
Recording Mode => Play Mode change
Manual impact file recording
Audio Recording mode change (On/Off)
Size x2 => Size x4 => Original size
Play mode => Recording Mode return
File Search
Main Cam. => LCD Off
N.A.
Main Cam. => Rear Cam.
=> LCD Off
Main Cam. => Rear Cam.
Parking / Driving mode recording change
(Not applicable when “Auto Parking mode” selected)
2 ch. Mode
Short
Play Mode
Recording
Mode
P
Button
Short
P
Button
Short
Short
V
Button
Short
V
Button
P
Button
Long
min.3sec
Long
min.3sec
P
Button
Long
min.3sec
SHOT
Button
Short
SHOT
Button
SHOT
Button
www.visiondrive.co.kr
Product Use VD-8000HD Button Instruction
Division