Vision Fitness R2100 User manual

ASSEMBLY INSTRUCTIONS
R2100
To avoid possible damage to this Fitness Cycle,
please follow these assembly instructions.
Carefully remove all its parts from the box,
lay them out and review the parts list.
If any parts are missing, please call 1-800-335-4348, Ext 12
Before proceeding, find your Fitness Cycle’s serial number,
located on the underside of main frame, and enter here:
______________________________
Refer to this number when calling for service.
IT ALL STARTS WITH A VISION

R2100 Parts Diag ram

VISION FITNESS R2100 Parts Description
Part # Description Count Dimensions
Front Wheel Parts
#148 Front Foot Wheel Axle 1
#149 Front Transport Wheels 2
#150 Inside Wheel Washers 2
#185 Outside Wheel Washers 2
#182 Wheel Attachment Bolts 2 20mm L x 8mm D
Rear Rail Support Bars
#106 Rear Foot Assembly 1
#182 Rear Foot Attachment Bolts 4 20mm L x 8mm D
#91 Rear Foot Frame Extension 1
#182 Frame Extension Bolts 4 20mm L x 8mm D
#96 Seat Rail Support Post 1
#186 Support Post Bolts-Bottom 4 55mm L x 8mm D
#184 Top Post Bolt Washers 4
#121 Aluminum Seat Rail 1
#182 Seat Rail Mount Bolts 2 20mm L x 8mm D
#125 Seat Stop Bumper Rod 1
#124 Seat Stop Bumpers 2
#188 Bumper Rod Bolts 2 10mm L x 3mm D
#189 Bumper Rod Lock Washers 2
#129 Seat Rail End Cap 1
#174 Seat Rail End Cap Screws 2
Seat Parts
#115 Seat Frame 1
#137 Seat Cushion Back 1
#136 Seat Cushion Bottom 1
#195 Seat Cushion Bolts 8 55mm L x 6mm D
#196 Seat Cushion Bolt Washers 8
#110 Seat Mount Handlebars 1
#182 Seat Mount Handlebar Bolts 4 20mm L x 8mm D
Console Parts
#101 Console Mast 1
#182 Console Mast Allen Bolts 6 20mm L x 8mm D
#88 Rubber Console Mast Cover 1
#153 Console 1
#220 Upper Magnet Shift Cable 1
#66 Lower Magnet Shift Cable
#197 Console Attachment Bolts 6 11mm L x 5mm D
#225 Indexed Mast Cover 1
#64 RPM Sensor Wire 1
Other Parts
#152 Pedals 2
#199 Pedal Straps 2
R2100 Parts

R2100 Assembly
Step 2 • Seat Support and Rear Foot
1:Attach the Seat Rail Support Post (96) to the top of the Rear Foot Frame
Extension (91) with four Bottom Support Post Bolts (186). Tighten with a
5mm Allen wrench.
2:Secure the Rear Foot Frame Extension (91) to the frame bracket using the
four Frame Extension Bolts (182).
3:Secure the Rear Foot Assembly (106) to the Rear Foot Frame Extension
(91) using the four Rear Foot Attachment Bolts (182). Tighten with a
5mm Allen wrench.
NOTE: During each assembly step, ensure that ALL nuts and bolts are in
place and partially threaded in before completely tightening any ONE bolt.
Step 1 • Front Wheel Assembly
1:Slide the Front Foot Axle (148) through the Front Foot Nylon Sleeves (147).
2:Place the Inside Wheel Washers (150) on the Front Foot Axle (148).
3:Slip the Front Transport Wheels (149) onto the Front Foot Wheel Axle
and secure them with the outside Wheel Washers (185) and the Wheel
Attachment Bolts (182) using two 5mm Allen wrenches.

R2100 Assembly
Step 3 • Seat Assembly
1: Secure the Seat Mount Handlebars (110) to the Seat
Frame (115) with four Seat Mount Handlebar Bolts
(182) and four washers (156).
2: When mounting the Seat Cushion Bottom (136), you
have two sets of holes to choose from. Using the rear
set of holes is recommended for most people. For a
smaller person, you may choose to use the forward set
of bolt holes. Mount the Seat Cushion Bottom (136) to
the Seat Frame (115) with four of the Seat Cushion Bolts
(195) and Seat Cushion Bolt Washers (196) using a 4mm
Allen wrench. Do not fully tighten any bolt until all four
bolts are started.
3: Mount the Seat Cushion Back (137) to the Seat Frame
(115) using the remaining four Seat Cushion Bolts
(195) and Washers (196). Do not fully tighten any bolt
until all four bolts are started.
Step 4 • Aluminum Seat Rail
1: Place the Aluminum Seat Rail (121) on the Seat Rail
support (96) and align the two holes in the Seat Rail
with the two holes in the Frame Lip (299) . Thread the
Seat Rail Mount Bolts (182) through the Frame Lip (299)
into the Aluminum Seat Rail but do not tighten yet.
2: Secure the Aluminum Seat Rail (121) to the Seat Rail
Support Post (96) with the four Top Support Post Bolts
(182) and Top Post Bolt Washers (184). Tighten these
four bolts. Now fully tighten the two Seat Rail Mount
Bolts (182) at the front of the seat rail.
3: Slide the Seat Frame (115) onto the Aluminum Seat Rail
(121) while lifting the knob, so the seat frame will slide to
the front of the seat rail.
4: Slide the Seat Stop Bumper Rod (125) with one Seat
Stop Bumper (124) already attached through the hole
in the back of the Aluminum Seat Rail (121). Attach the
second Seat Stop Bumper to the other end of this rod
using the Bumper Rod Screw (188) and Bumper Rod Lock
Washer (189).