Vision ZL 7432 IN User manual

Operation
Turn on or turn off two individual appliances that attached to ZL7432 by Z-Wave™
Interface Controller
Federal Communications Commission Statement
This equipment has follows with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation.This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try and
correct the interferene by one of the following measures:
Reorient or relocate the receiving antenna,
Increase the separation between the equipment and receiver,
Connect the equipment into and outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undersired
operation.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate this
equipment.
Limited Warranty
Vision Guarantees that every In-Wall Switch module is free from physical defects in
material and workmanship under normal use for one year from the date of purchase. If
the product proves defective during this one-year warranty period, Vision will replace it
free of charge. Vision does not issue any refunds. This warranty is extended to the
original end user purchase only and is not transferable. This warranty does not apply to :
(1) damage to units caused by accident, dropping or abuse in handling, or any negligent
use; (2) units which have been subject to unauthorized repair, taken apart, or otherwise
modified; (3) units not used in accordance with instruction; (4) damages exceeding the
cost of the product; (5) transit damage, initial installation costs, removal cost, or
reinstallation cost.
For information on addional devices, plesae visit us at www.visionsecurity.com.tw
Installation & Operation Manual
ZL 7432 IN
ZL 7432 EU
ZL 7432 RU
ZL 7432 US
ZL 7432 IS
ZL 7432 JP
ZL 7432 BR
In-Wall Switch, 2 Relays
ZL 7432
V1
1030327
6B1Z-74005
-3-

Introduction
Thanks for choosing the Vision’s In-Wall Switch module of the home automation device.
This module is a Z-Wave™enabled device (interoperable, two-way RF mesh networking
technology) and is fully compatible with any Z-Wave™enabled network. Every mains
powered Z-Wave enabled device acts as a signal repeater and multiple devices result in
more possible transmission routes which helps eliminate “RF dead-sports”.
Z-Wave™enabled devices displaying the Z-Wave™logo can also be used with it
regardless of the manufacturer, and ours can also be used in other manufacturer’s
Z-Wave™enabled networks. With special design, this module can fit into most of
electronic box in the market. This module will send On/Off signal to the appliance that
attached to this module by receiving Z-Wave™signal from controller. It also can control
two appliances independently.
Product Description and Specification
Specification:
Package Content
Protocol: Z-Wave™(ZM3102N)
Frequency Range:
865.22MHz (ZL7432IN)
868.42MHz (ZL7432EU)
869.00MHz (ZL7432RU)
908.42MHz (ZL7432US)
916.00MHz (ZL7432IS)
920.00MHz (ZL7432JP)
921.42MHz (ZL7432BR)
Operating Range: Up to 100 feet line of sight
Operating Temp.: -15°C~ 60°C(5°F~140°F)
Operating Voltage: 100VAC~240VAC
Resistive Load:
550W for 110VAC
1100W for 220VAC
1pc ZL 7432 In-Wall Switch,
2 Relays
1pc Installation & Operation
Manual
Z-Wave™ Command Class
COMMAND_CLASS_ASSOCIATION
COMMAND_CLASS_MANUFACTURER_SPECIFIC
COMMAND_CLASS_MULTI_CHANNEL_V3
COMMAND_CLASS_SWITCH_ALL
COMMAND_CLASS_SWITCH_BINEARY mapping COMMAND_CLASS_BASIC
COMMAND_CLASS_VERSION
Installation
Notice: If you are installing the entire Z-Wave™ system for the first time, please refer to
the installation guide of Z-Wave™ Interface Controller before installing ZL7432 In-Wall
Switch Module.
1. Following the wiring diagram to install ZL7432 according to your varied
requirements.
Note: Place antenna toward the surface and away from metal to get better signal.
2. For “Inclusion” in (adding to) a network:Put the Z-Wave™ Interface Controller
into “inclusion” mode, and following its instruction to add the ZL 7432 to your
controller. To get in the “inclusion” mode, the distance between module and
controller is suggested to be in one meter. Turn on and turn off the wall switch that
connects with ZL 7432 module 4 times to be included. (or press the Program SW 4
times within 2 seconds to be included)
For “Exclusion”from (removing from) a network: Put the Z-Wave™Interface
Controller into “exclusion”mode, and following its instruction to delete the ZL 7432
from your controller. Turn on and turn off the wall switch that connects with ZL
7432 module 4 times to be excluded. (or press the Program SW 4 times within 2
seconds to be excluded)
3. For Wall SW1, ZL 7432 will report the status of On/OFF after doing “Association”.
However, Wall SW2 will only report the status if Z-Wave™ Interface Controller
support Multi Channel command, and send Get Command to ask ZL 7432 Wall SW
2 to report the status.
4. User can use the following command class to control relay 1 and/or 2 in order to
control the appliances that attached to ZL7432
For relay 1:
Status of “ON”(Binary Switch Set 0xFF or wall switch ON)
Status of “OFF”(Binary Switch Set 0x00 or wall switch OFF)
For relay 1 or 2: Please use Multi-Channel command class to control
5. Reset to the factory default setting: Press and hold the Program SW before power
on.
-1-
-2-