VISIONARY DESIGNS MOD-1234 Manual

© 2019
Order #XXXXX
*
*
Completed Stand Assembly
Counter Top
*
Monitor Mount
Attachment
Slide connectors into
grooves of verticals.
Tighten set screws.
Attach monitor mount
to connectors, using bolts.
Connectors
Monitor
Mount
*
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Attachment
12
*
Pin
Hole
Connector
Literature Holder Attachment
Locks
Literature
Holder
Attach angled end of connector to
literature holder. Attach flat end of
connector to vertical extrusion.
Tighten locks to secure.
*
*
*
*
*
Door
Hinge
Hinge
Pin
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Connection
*
V15
Connector
Extrusion Connector
Slide upper extrusion
over connector and
rest on lower extrusion.
Secure with set screws.
*
To prevent product loss,
keep all screws attached
to connector after
disassembling.
Set Screw
Infill
InfillInfill
Infill Door
Shelf
Item
1
2
3
4
5
6
7
Description
37.5” Q914 Vertical Extrusion w/ Hinges
37.5” Q914 Vertical Extrusion w/ Door Stop
32.5” Q914 Vertical Extrusion
37.5” Q914 Vertical Extrusion
13.5” Z45 Horizontal Extrusion
14.5” Z45 Horizontal Extrusion
14.5” Z45 Horizontal Extrusion
Qty.
1
1
2
2
5
2
2
4
4
3
3
1
2
5
7
6
6
7
5
5
5
5
*
*
Steps:
1) Attach verticals [1 to 3] and [2 to 3]. See Extrusion Connector detail.
2) Attach front assembly [4] [5] and infill to back assembly [1/3] [2/3] and [5] with [6] [7] and infills.
3) Connect door to vertical [2]. See Door Connection detail.
4) Connect shelf supports to Velcro on inside of assembled stand, then set shelf on top of supports.
5) Lock counter top to horizontals [7]. See Counter Top Attachment detail.
6) Attach monitor mount to verticals [3]. See Monitor Mount Attachment detail.
7) Attach literature holders to verticals [1] and [2]. See Literature Holder Attachment detail.
When Packing:
Keep extrusions [1] [2] and [5] with door assembled.
Keep extrusions [4] and [5] with infill assembled.
Keep V15 connectors attached to extrusions [1] and [2].
MOD-1234 Monitor Stand
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2019
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information