VISIONARY DESIGNS VK-1369 Manual

© 2024
Locked layer contains
placeholder marks.
Plan View
10’
10’
VK-1369 - 10’ x 10’ Inline
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2024
Locked layer contains
placeholder marks.
= 1 sq foot
Grid View

© 2024
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2024
Straight Connection
All knobs must be tightened securely to ensure a proper connection.
All knobs must be tightened securely to ensure a proper connection.
Adjust connectors if necessary to
prevent gaps in connection.
Upper Horizontal Extrusion
Lower Horizontal Extrusion
Straight Connector
Straight Connector
Corner
Connectors Corner
Connectors
Corner
Connectors Corner
Connectors
COMPLETED ASSEMBLY
3) Tighten all knobs to secure connection.
Slide verticals over
lower connectors.
Then slide upper
connectors into
groove of verticals.
Tighten all knobs.
When assembling frame, first attach all straight
connectors, then attach corner connectors.
1) Place extrusions end-to-end.
2) Loosen all knobs, then slide straight
connectors across the seam of extrusions.
Disassembly
1) Loosen all knobs.
2) Slide connectors off of one extrusion.
3) Tighten knobs to prevent loss during
packing & shipping.
CEI110 Profile
Slide both connectors across seam of extrusions.
Tighten all knobs.
Corner Connection
3) Tighten all knobs to secure connection.
Disassembly
1) Loosen knobs on vertical extrusions.
2) Slide the vertical extrusions off of
corner connectors on lower and upper
horizontal extrusions.
1) Loosen knobs, then slide vertical extrusions onto
corner connectors of lower horizontal extrusion.
2) Slide corner connectors of upper horizontal
extrusion into grooves of vertical extrusions.
Keep straight connectors in groove of
extrusion. Do not remove connectors
during disassembly.
CEI110 Frame Assembly

© 2024
Graphic Removal
To remove the graphic
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
from
SEG Installation

© 2024
Case 1 of 3
Locked layer contains
placeholder marks.
Top View of Each Level
Setup Hardware
Monitor Mount
6,6A
Level 1
(Bottom level)
7 7
Level 2
4 5 6,6A
Level 3
4A 5A
VK-1369 Backwall
Case Packing

© 2024
Case 2 of 3
Locked layer contains
placeholder marks.
Top View of Each Level
Graphics
1A3A 1 3 2A 2
Level 1
(Bottom level)
Level 2
VK-1369 Backwall
Case Packing

© 2024
Case 3 of 3
Locked layer contains
placeholder marks.
Top View of Each Level
Level 1
(Bottom level)
Level 2 Level 3 Level 4
Door
3/4/7/7A
1/1A/2/2A
5,5A,6,6A
Counter
Top
Shelf
Infills
Shelf Supports
MOD-1701 Counter
Case Packing

© 2024
Step 1 of 4
Locked layer contains
placeholder marks.
When assembled
Steps:
Refer to the CEI110 Frame Assembly general information page.
1) Assemble horizontals [1-2-3], [1A-2A-3A] & verticals [4-5], [4A-5A]
using tool-less spline connectors.
2) Connect vertical assemblies [1/2/3], [1A/2A/3A] between
horizontals [4/5], [4A/5A] using tool-less corner connectors.
3) Attach verticals [6-6A] between horizontal assemblies [1/2/3],
[1A/2A/3A]. See Z45 Attachment detail.
4) Connect Base Plates [7] to assembled frame.
See Base Plate Attachment detail.
*
*
Item
1,1A
2,2A
3,3A
4,4A
5,5A
6,6A
7
Qty.
1,1
1,1
1,1
1,1
1,1
2,2
2
Description
38” CEI110 Horizontal Extrusion
38” CEI110 Horizontal Extrusion
38” CEI110 Horizontal Extrusion
47.5” CEI110 Vertical Extrusion
47.5” CEI110 Vertical Extrusion
45.677” Z45 Vertical Extrusion
Base Plate
Assemble frame flat on ground.
*
Base
Plate
Bolt
Fixed Bolt
Bolt
Vertical
Extrusion
Horizontal
Extrusion
Base Plate Attachment
Place key hole over fixed bolt on
assembled frame, then slide down.
Secure with bolts, washer, and wing nut.
Washer
Wing Nut
Key Hole
FRONT VIEW
1
2
3
1A
5
4
5A
4A
7
7
6A
6
6A
6
2A
3A
**
**
CEI-110
Z45
Z45 Attachment
Attach Z45 vertical to back
groove of CEI-110 horizontal.
*
FRONT VIEW
Backwall Assembly

© 2024
Step 2 of 4
Locked layer contains
placeholder marks.
Steps:
1) Connect power cords to Supernova lights, as shown.
ELEVATION VIEW
Power
Break
Power
Break
Power
Break
+
-
Power
Female
Transformer
144W / 6 Amp / 24V
++
--
Lights Male
Light to Light Attachment
Maximum of 7 lights per chain / 11 lights per Transformer
Light to Transformer Attachment
Transformer TransformerTransformer
Lightbox Wiring

© 2024
Step 3 of 4
Locked layer contains
placeholder marks.
SEG Blocker
Steps:
Refer to the SEG Installation general information page.
1) Apply SEG Graphic to front of assembled frame.
2) Install Monitor Mount to verticals [6/6A] using standoff barrels.
See Monitor Mount Attachment detail.
3) Apply SEG Blocker to back of assembled frame.
Vertical Extrusion
Monitor
Mount
Standoff
Screw standoffs into vertical extrusions. Attach
monitor mount to standoffs, using caps
Standoffs attach through SEG graphic.
*Monitor Mount Attachment
Cap
SEG Graphic
Item
--
--
Qty.
4
1
Description
Standoff Barrel
Large Monitor Mount
When assembled
FRONT VIEW
S
E
G
Grap
h
ic
Monitor
Mount
6/6A 6/6A
Backwall Attachments

© 2024
Step 4 of 4
Locked layer contains
placeholder marks.
*
Steps:
1) Attach horizontals [1] and [1A] between verticals [2] and [2A],
with infill placed into inside grooves. See CEI110 Corner
Connection instruction on reverse side.
2) Attach horizontal [5] between verticals [2A] and [4], sliding
infill into grooves of verticals, then secure with horizontal [5A].
Make sure Velcro is facing inward and at bottom.
3) Attach horizontal [6] between verticals [2] and [3], sliding
infill into grooves of verticals, then secure with horizontal [6A].
Make sure Velcro is facing inward and at bottom.
4) Attach horizontals [7] and [7A] between verticals [3] and [4].
5) Connect door to vertical [3]. See Door Connection detail.
6) Connect shelf supports to Velcro on inside of infills, then
place shelf on top of supports.
7) Connect lights and transformer. See Light Connection details.
8) Install SEG graphic to front of assembled light frame.
See SEG Graphic Installation instruction on reverse side.
9) Lock counter top to [5A] and [6A]. See Counter Top Lock detail.
Item
1,1A
2,2A
3
4
5,5A
6,6A
7,7A
Qty.
1,1
1,1
1
1
1,1
1,1
1,1
Description
22.1654” CEI110 Horizontal Extrusion
38” CEI110 Vertical Extrusion w/ S10
38” S44 Vertical Extrusion w/ Door Hinges
38” S44 Vertical Extrusion w/ Door Stop
16” Z45 Horizontal Extrusion
16” Z45 Horizontal Extrusion
18.5” Z45 Horizontal Extrusion
Completed Assembly
(infills not shown)
Counter Top
Shelf
shelf support
shelf support
shelf support
shelf support
BACK VIEW FRONT VIEW
(Infills Not Shown)
1
1A
2
2A 2
2A
I
nfi
l
l
D
o
o
r
I
nf
i
ll
I
nf
i
ll
5
3
6
4
7A
7
5A
6A 5A
6A
*
*
*
++
+
-
-
-
to power
Lights
Male
Male
Female
Female
Transformer
48W / 2A / 24V
Light to Light Connection
Light to Transformer Connection
Maximum of 3 lights per transformer.
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Lock
12
*
Pin
Hole
Door
Hinge
Hinge
Pin
Slide Pin into
Hinge attached
to Vertical.
Slide Door
Hinge over Pin.
Door Connection
*
Counter Assembly