VISIONARY DESIGNS Sacagawea VK-1215 User manual

www.classicexhibits.com
Step 1
Page 1 of 5
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea - VK-1215 - General Layout
10’
10’
Plan View

www.classicexhibits.com
Step 2
Page 2 of 5
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C EliateDDliateDDetail B
Detail A
Setscrews

www.classicexhibits.com
Step 1
Page 1 of 5
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea - Backwall Assembly
Set upper horizontal bars
[51/5b] to be flush with
top of vertical extrusions.
Horizontal Placement
3a
5a
2a
3a
1
4a
1
2
3
5a
4b
5b
Connection
Bar
Slide Connection Bar
between Extrusions
and tighten Knobs
to secure.
Connection
Bar
Graphic Attachment
Apply graphic to back
of assembled backwall.
Connection
Bar
a
a
b
Connection
Bar b
A10 clamps attached to vertical extrusions fo Wing Attachment
Item
1
2
3
2a
3a
4a/4b
5a/5b
Description
Base Plate
42”h Lower Square Vertical Extrusion
42”h Upper Square Vertical Extrusion
42”h Lower Square Vertical Extrusion w/ A10 Clamps Attached
42”h Upper Square Vertical Extrusion w/ A10 Clamps Attached
45”w Horizontal Extrusion
45”w Horizontal Extrusion
Qty.
2
1
1
1
1
1/1
1/1
Steps:
1) Attach vertical extrusions [2] to base plates [1].
2) Attach upper vertical extrusions [3a and 3] to lower extrusions [2a and 2]
using connection bar [a].
3) Connect horizontal extrusions [4a to 4b and 5a to 5b] together using connection bar [b].
4) Attach horizontal assemblies [4a/4b and 5a/5b] between vertical assemblies as shown.
5) Apply graphic to back of assembled backwall.
6) Attach light to top of assembled backwall.
Turn Knob Clockwise
to Tighten Lock
STAR indicates location of
knobs on BACKSIDE of unit.
**Do not over tighten Knobs.**
Knob
Knob
Light Connection
Attach Lights to
Backwall where
desired and tighten
in place.
GREEN STAR indicates
location of connection
lock with knob.

www.classicexhibits.com
Step 2
Page 2 of 5
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea -
Item
7
8
9
Description
9.2856”h Vertical extrusion
9.2856”h Vertical extrusion
43.66”w Curved Horizontal Extrusion
Qty.
1
1
1
Steps:
1) Connect curved horizontal extrusion [9] between vertical extrusions [7 and 8].
2) Attach assembled header to top of assebled backwall as shown.
**NOTE: Header must stay assembled when shipping
8
9
Lock header frame to top of assembled backwall
Extrusion Lock
Extrusion Lock
Graphic Attachment
Velcro graphic to BACK of
assembled header frame.
7
Header Attachment

www.classicexhibits.com
Step 3
Page 3 of 5
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea -
*Note: Curved extrusion
[10] and horizontal [11]
must stay assembled
when shipping.
Item
10
11
11a
Description
30.2” Curved Extrusion
12.184”w Horizontal Extrusion
Flange Plate
Qty.
1
1
1
Steps:
1) Connect horizontal extrusion [11] to curved extrusion [10].
2) attach assembled counter support [10/11] to vertical where indicated.
3) Attach flange plate [11a] to top of curved extrusion [10] as shown.
4) Attach counter atop support, see counter top attachment detail.
5) Attach wing panels to A10 clips.
6) Attach monitor mount to backwall where indicated.
Counter Top Attachment
Insert screws located on underside
of counter into holes on flange plate
and secure with wing nuts.
Wing Nut
Screw
10
11
11a
Monitor Mount Attachment
Connectors
Attach monitor mount back plate
to connectors using screws provided.
Slide A10 Clamp
into groove
of square extrusion.
When desired location
is found, tighten
set screw to secure.
Set-
Screw
A10
Tighten black plastic
set screw to secure
Wing in place.
Black Plastic
Set-screw
Wing Attachment
*Note: A10 clamps must
stay attached with verticals
Counter and Wing Attachment

www.classicexhibits.com
Step 4
Page 4 of 5
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea - Canopy Assembly
Connections are made by holding the button
down and sliding the red tube into opposing
tube until the connection is made. To disassemble
push button and pull or twist extrusions apart.
Push-Button
Push-Button
66
6
6
Numbered Label
Using Your Setup Instructions
The Aero Overhead Sign Setup Instructions are created specifically for your configuration. They include an
exploded view of the frame which is sequentially numbered. We encourage you to study the instructions
before attempting to assemble your exhibit.
Connections are kept very simple: no tools. Everything assembles with push-button
connectors and pre-connected horizontal sections.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
Steps:
1) Connect canopy pieces together as shown.
2) Apply pillow case graphic to assembled canopy
AA
BB
DD
CC
Push-Button
Push button then rotate
for packing purposes

www.classicexhibits.com
Step 5
Page 5 of 5
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea - LTK-1001 - Pedestal Assembly
Setup Instructions:
A) Use standoff screws to secure the front panel with
door and back panel of the pedestal to the side panels.
B) After assembling front, back, and side panels,
slide floor into the bottom of the pedestal. The
floor will sit on pins on the inside of the side panels.
C) After floor is in place, use velcro attachments to
install shelf.
Standoff
Screw
Front Panel
with Door
Floor
Shelf with
Velcro Supports
Attach the oval counter
top to the pedestal base.

www.classicexhibits.com
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Case Packing Instruction - Case 1 of 2
Extrusions #3&3a
Extrusions #2&2a
Horizontal extrusions #4a&4b abd 5a&5b
Counter
Top
Base Plates
Backwall Counter
Support
Level 2 Level 3
Canopy
Slip Sheet
Setup Hardware and Graphics
Halogen LightHalogen Light
Connection Bars B and A
Level 1
Wing Panels
Assembled Header
(1) Backwall Components

www.classicexhibits.com
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Case Packing Instruction - Case 2 of 2
Counter Top (2) Side Panels Front Panel w/ Door
+ Back Panel
Floor and Internal Shelf
Level 2Level 1 Level 3 Level 4
(2) Pedestal Components