Visionis VIS-8011 User manual

Access Control RF Wireless 433MHz Indoor
Receiver
VIS-8011
User Manual
www.visionistech.com

Specifications
Operating Voltage
Mini Controller
12V DC ±20%
Current
Idle Current
Working Current
≤20uA
≤50mA
Communication Frequency
433MHz
Communication Distance
50m Maximum (165 feet)
Relay Contact Load
2Amp Maximum
Environment
Operating Temperature
Operating Humidity
Indoor
-20°C~60°C (-4°F~140°F)
0%~86%RH
Physical
Dimensions
Unit Weight
ABS Shell
L85 x W50 x D25(mm) - L3.35 x W1.96 x D0.98(in.)
62g
INSTALLATION
Method 1: Stick by 3M stickers
The device packed with 3M double-side Sticker, can easily stick the Mini Controller on Metal door, Glass Door,
Wooden Door, or Smooth Wall.
Method 2: Install by screws

Wiring (Mini Controller)
No.
Function
Notes
1
GND
Negative Pole of DC (12V) Power Input
2
+12V
Positive Pole of DC (12V) Power Input
3
ALARM-
Negative Contact for Alarm
4
COM
Common Connection for Relay Output
5
NO
Normally Open for Relay Output
6
LOCK+
Positive Pole of Lock Power Input
7
NC
Normally Close for Relay Output
8
OPEN
Contact to One Wire of Exit Button
9
D_IN
Door Status Detecting
10
BELL_A
Contact for Doorbell
11
BELL_B
Contact for Doorbell
Connection Diagram
Access Control Power Supply:
Common Power Supply:

Attention: Install a 1N4004 or equivalent diode is needed when use a common power supply,
or the reader might be damaged. (1N4004 is included in the packing)
Pair Wireless Keypad / Exit Button and Mini Controller
1. They are already paired when out of the factory, if no problem, the users do not need to do this operation in use.
2. One Mini Controller can be connected by 5 pieces of Wireless Keypad and Exit Button maximum.
To pair the wireless keypad and the controller:
Mini Controller: Remove the back cover and press the button “Pair”.
Wireless Keypad: * Master Code # 8 0 #, press * on the keypad to exit.
If pair successfully, there will be one beep from both the controller and the keypad; if not, there will be three short
beeps, then please repeat the setting.
To pair the wireless button and the controller:
Mini Controller: Remove the back cover and press the button “Pair”.
Wireless Button: Remove the back cover and press the button “Pair”.
After hearing one beep, press “Pair” again to exit pairing mode.
If pair successfully, there will be one beep from both the controller and the exit button; if not, there will be three short
beeps, then please repeat the setting.
To pair the wireless keypad with multiple mini controllers:
Wireless Keypad: * Master Code # 8 0 #
Mini Controller: Remove the back cover and press the button “Pair”.
(Same settings for multiple controllers)
If pair successfully, there will be one beep from both the controller and the keypad, press * on the keypad to exit
pairing mode; if not, there will be three short beeps, then please repeat the setting. Users need to finish the pairing
within 30s for multiple controllers, or else, the keypad will exit pairing mode automatically.
To pair the wireless button with multiple mini controllers:
Wireless Button: Remove the back cover and press the button “Pair”.
Mini Controller: Remove the back cover and press the button “Pair”.
(Same settings for multiple controllers)
If pair successfully, there will be one beep from both the controller and the button, press the button “Pair” on the
button to exit pairing mode, if not, there will be three short beeps, then please repeat the setting.
Users need to finish the pairing within 30s for multiple controllers, or else, the keypad will exit pairing mode
automatically.