Visiotech HY-AC672 User manual

This model design concise, easy to use fingerprint
entrance guard terminal equipment, and can be
installed in those who need to enter the
authorized sensitive area, innovation in the
fingerprint identification is a high security and
senior gateway management together, achieve
access control of high safety management.

1
OK Confirm key: make sure your current operation；
MENU Menu button: In the initial condition according to the key can enter the
management interface；
ESC Cancel button：Cancel your current operation；
▲Up key: Turning up menu items；
▼Down key: Turning down menu items；
The bell button: Control the doorbell switch；
Digital：Input digital 0-9；
The wiring diagram
Key description

2
Note: when choosing a password or ID card (machine with the function), the name of the
person can be uploaded through the access control software;
Press the keyboard "MENU"
into the machine "MENU"
Select "User" by
"0K" or "1" key
Select "New"
Select“Finger”
Enter the number,
press"OK"
Register the fingerprint
by the machine
EnrollOK！
Continue second?
"OK" option to backup, "ESC"
to end the registration
Press the keyboard "MENU"
into the machine "MENU"
Select "User" by
"0K" or "1" key
Select“Modify”
According to the “↓↑”by any
choice or quick input number，
select Modify username, press
OK
To "OK" confirm Press，
Press "ESC" to complete
According to the “↓↑”
choice “Privilege”Through
the“↓↑”and select“Admin”
1.1 Registered users
1.2Administrator setting

3
Note: after setting the administrator, the menu needs to be confirmed by the administrator, the success
of the menu;
;
☆Baudrate：communication with the computer communications rate, were 9600, 19200,
38400, 57600, 115200 five option;
☆Device IP：the default IP for the 192.168.8.198, you can according to the need for change;
☆Subnet mask：the default for 255.255.255.0, you can according to the need for change;
☆Default gateway：the default for 192.168.8.1, you can be the basis of the need for
change;
☆Device port：communication used the port number, the default for 5005;
☆Server IP：the default for 192.168.0.1, real-time monitoring of the computer when IP
address, you can be the basis of the need for change;
☆Server port：communication port, the default used for 7005;
☆Realtime Req：real-time monitoring fingerprint access to the computer when whether to
send data. The default is no;
Note: the need to use the network interface communication when it is necessary to carry
out the setting, if the USB communication is directly inserted into the USB line;
Remarks：
☆Time setting：is defined time for a week each day can unlock the definition of the time;
☆Users：user entrance guard Settings is the user the lock and unlock the set time
combination;
☆Unlock Time：is fingerprints machine control open or close the locks of the time;
☆Lock Type Set：includes three kinds:：No、Open、Close；“No”refers to not use magnetic
switch on the door，“ Open”often a door lock is to open,，“ Close”the door closed to
lock the shu started the multicolored;
☆Anti Pass：To prevent the following entry;
Press the keyboard
"MENU" into the
machine "MENU"
Select “Setting”
by "0K" or "3" key
Select "LockCtrl" and
"0K" to make the
relevant settings.
2. Entrance guard function setting
1.3 Communication settings
Communication settings
Press the keyboard
"MENU" into the
machine "MENU"
Select“Setting”by
"0K" or "3" key
Select "Network"
set the appropriate
TCP/IP

4
☆Alarm Time：is open the door for some time after began to call the police, this paragraph
of time is door magnetic delay
☆Turn Off Alarm：in alarm has trigger, and has ruled illegal operation, but not by this
option to stop the police.
①This is the preference when you buy ②As seen here: grip the two sides of
the machine；frame cover, pull outward slightly
③As seen here: take out the frame ④As seen here: put screws in place
cover from bottom to top；red marked, and install the device
on the wall.
Noted: Fasten the orientation
template on the wall first, and
put the sealing ring on, then
install the device.
3. Fingerprint Integrated
Machine install guidance

5
⑤Put the frame cover back ⑥ Put the frame cover back from
top to button
⑦Lock the frame cover from outside。
In addition to the machines, the box also contains the following items:
Operating Instructions 1PCS USB data cable 1PCS Screws 4PCS
Up stopper 4PCS Ring 1PCS Installation positioning template 1PCS
Terminal (2P, 3P, 4P, 10P each one)
4. Packing List