Visiotech T5Pro User manual

Relay State
12V
12V COM COM
Port
PIN
12 6 5 4 32 1
Function
Connector
+12V GND GND GND D1 D0
Mark +12V GND
Wiegand Output
P2P1
Power Supply
GND D1 D 0 Mark
Switch Power Access control
Port
PIN 1 2 8 7 6 5 4 3 2 1
Function GND
Connector +12V GND NO NC COM GND OPEN DOOR
Power Supply
Output Controller
P1 P3
Access Control Power Supply Switch Power Supply
Port
PIN 12 8 7 6 5 4 3 2 1
GND
+12V GND NO NC COM GND OPEN DOOR
Power Supply
P3P1
Access Control Reader & Controller Communicate with PC
RS485B RS485A
RS485
Exit
Button
Door
sensor
Power off to unlock
Relay State
Function
Connector
Output Controller
Exit
Button
Door
sensor
P1
PIN
Cable
Color
Description
Function
Power 1
2
Red
DC12V
Black GND
Trigger Input
Trigger Input
Orange
Blue
P3
Door Sensor
GND
Relay
Exit Button
1
2
3
4
5
6
7
8
NO
NC
COM
GND
P2
Wiegand
Output
1
2
3
4
5
6
Purple
Yellow
White
GND
GND
Wiegand DATA0 Output
Wiegand DATA1 Output
Green
RS485
RS485A
RS485B
P
1
P2
P3
RJ45(TCP/IP)
Relay
6
7
6
7
NO
NC
COM
3
P
P
3
Relay
8
8
DC12V
COM
DC12V
12VCOM 12VCOM
Relay states
Function PIN
Cable
Color
Description
Black
Black
Black
Purple
Yellow
Green
White
Function PIN
Cable
Color
Description
White
Important notice: Please carefully follow this wiring diagram, If the reader gets damaged by
incorrect wiring then your warranty will be void.
Wiring Instruction
Installation Steps:
1
2
3
Drill holes in the wall follow the hole position on back panel
Install and fix back panel, connect related cables
Fix access control reader
Installation Diagram
1
Reader Instruction Package
特别说明：门禁机是高度集成化的精密电子产品，任何错误的连接都可能导致
门禁机的元器件损坏，因此连接各种设备之前，请仔细阅读接线说明。
排线说明
考勤 门 禁 一 体 机
P
1
线 颜色 描述功能
电源 1
2粗红 电源
DC12V
粗黑
GND
P
4
线 颜色 描述功能
门铃
1
2白
白
触发输出
触发输出
紫 触发输入
触发输入黄
黑
绿
橙
蓝
P
3
线 颜色 描述功能
门磁
接地
继电器
出门按钮
1
2
3
4
5
6
7
8
GND
COM
NC/DC12V
NO/DC12V
P
2
线 颜色 描述功能
韦根输出
1
2
3
4
5
6黑
紫
黄
黑
白
GND
GND
韦根
DATA0
输出
韦根
DATA1
输出
绿
RS485
RS485A
RS485B
P
1
P
2
P
3
P
4
继电器状态
继电器
6
7
8
COM
NC
NO
P3
P3
继电器
6
7
8
COM
DC12V
DC12V
12VCOM
12VCOM
TCP/IP
安装步骤
1
2
3
按后挂板孔位在墙上进行钻孔
安装固定后挂板，接好相关连线
固定主机
1
2
3
安装示意图
配件包
数据线
P1 P2 P3
P4
1主产品
2资料包
COMPACT
CD-ROM
EN
CH
CopyrightANVIZAllrightsreserved.
http://www.anviz.com
windows
FOR
Windows98
Windows2000
WindowsXP
WindowsVista
Windows7
装箱清单
78 9 OK/M
12 3 c/
45 6 0/
COMPACT
CD-ROM
ENCH
windows
FOR
Windows98
Windows2000
WindowsXP
WindowsVista
Windows7
Accesscontrol
Accessory Package
Select either
12 volt out on
COM or voltage
free contact.
Package list
Connector Jack
Access Control Reader & Power Supply Access Control Reader & Switch Power Supply
Mini-USB
TCP/IP
RS485
1
2
3
Mark
Door Sensor
Power on
to unlock
+12V PUSH NO GND NCGND
+
+
+
Mark
Power on
to unlock
Door Sensor
Diode
Diode
Power off
to unlock
+12V GND
+
+
+
The interface marked with for specific models,
Please according to the practical device to wiring.
P1 P2 P3 RJ45 USB
Red
Black Purple
V1.4

V1.4
Function button
Screw Hole
Mini USB Port
Reset Button
Notice: The operation will not delete any user data stored in the device.
Function Button
DC 12V supply the power for device. Blue LED flashes fast and Fingerprint Sensor lights with beeps.
There are 4 cards in the packing: Enroll Card Delete Card User Card * 2
Delete fingerprint only: (Operation Steps show as figure 1.4)
Delete Card / Card+Fingerprint: (Operation Steps show as figure 1.5)
After registed you can continue register another user or swipe
Enroll Card save and exit.
After delete you can continue delete another user or swipe
Delete Card save and exit.
After delete you can continue delete another user or swipe
Delete Card save and exit.
After registered you can continue register another user
or swipe enroll card save and exit.
After registed you can continue register another user or swipe
Enroll Card save and exit.
Add Card+Fingerprint: (Operation Steps show as figure 1.3)
Notice: When place finger, Red LED
flashes with long beep means the
fingerprint does not exist in the device.
Notice: When swipe card, Red LED
flashes with long beep means the
fingerprint does not exist in the device.
Continue to register
Blue LED
flashes
Swipe Enroll
Card, begin
Swipe Enroll
Card, end
Press the button until heard beeps, that eliminate Enroll Card and Delete Card information in the device. After that
MUST register management cards (Enroll Card and Delete Card) to run the machine.
Green LED lights
Four short beeps
In orginal state
Blue LED flashes
Red LED lights Green LED lights
Four short beeps
Figure 1.6
Continue to register
Swipe
User Card
Swipe User Card
again, please
Underneath:
Operation Guide
Reader Appearance
Figure 1.2
Add Fingerprint Only: (Operation Steps show as figure 1.1)
Blue LED
flashes
Place finger Place finger
again, please
Place finger Place finger
again, please
Place finger Place finger
again, please
Blue LED flashes fast
and FingerPrint
sensor lights up
Blue LED flashes fast
and FingerPrint
sensor lights up
Green LED lights up
Four short beeps
Registration Successed
Green LED lights up
Four short beeps
Registration Successed
Continue to register
Figure 1.1
Add Card Only: ( Operation Steps show as figure 1.2)
Notice:When swipe card, Red LED flashes
twice with two long beeps means the User
Card have been registered.
Notice:When swipe card, Red LED flashes
twice with two long beeps means the User
Card have been registered.
Notice: When place finger, Red LED flashes
with two long beeps means the finger
have been registered.
Figure 1.3
Continue to delete
Figure 1.4
Red LED flashes
Red LED flashes fast
Continue to delete
Figure 1.5
Always place finger in
the center of the sensor.
Make sure you cover the entire sensor surface
with as much of your finger as possible.
DO NOT place finger
away from the center
of the sensor window.
Correct method ( Straighten your finger and then place it on the sensor ensuring the finger is down flat and covers the entire sensor window)
:
Incorrect method :
:
Delete User:
Function Button
Register Management Cards (Enroll Card and Delete Card)
DO NOT slide your finger
during the fingerpint
verification process.
DO NOT take off finger
during the fingerprint
verification process.
DO NOT use just
your fingertip.
Illustration for placing finger
DO NOT move your finger
before the backlights of
sensor turns off.
LED
Card Reader Area
There are three colours
for device status: Red,
Blue and Green.
Swipe the card here.
Fingerprint Sensor
Place the finger here.
DO NOT place finger
at an angle.
Swipe Enroll
Card, end
Swipe Enroll
Card, begin
Swipe Enroll
Card
Swipe User Card
again, please
Blue LED
flashes
Swipe
User Card
Blue LED flashes
fast and FingerPrint
sensor lights up
Red LED flashes
fast and FingerPrint
sensor lights up
Red LED flashes
fast and FingerPrint
sensor lights up
Blue LED flashes
fast and FingerPrint
sensor lights up
Green LED lights up
Four short beeps
Registration Successed
Green LED lights up
Four short beeps
Delete Successed
Green LED lights up
Four short beeps
Delete Successed
Swipe Enroll
Card,end
Swipe Delete
Card, end
Swipe Delete
Card, end
Swipe Delete
Card, begin
Swipe Delete
Card
Swipe Delete
Card, begin
Swipe Enroll
Card, begin
Swipe
User Card
37mm
145mm
55mm