Vista 1093 User manual

INSTALLATION INSTRUCTIONS
Shroud
Adjustable
knuckle
Shroud
screw
1/2" NPT
Housing
Lamp Information
Cat No Lamp Type Max Watts
1093 R30, PAR30
Incandescent or HID
75
Up & Accent Lights
Architectural Series
1093
WARNING: Luminaire must be installed and grounded in accordance with the National Electrical Code (NEC) and local codes. For portable stake or
surface mount using a cord and plug, the luminaire must be plugged into a receptacle protected by a ground fault circuit interrupter (GFI). Failure to
do so may result in serious injury and/or damage to the luminaire.
MAINTENANCE: To assure proper operation and efficiency and to prevent luminaire overheating, lens must be kept clean and free of dirt, dust,
leaves, trash and mineral deposits from water. A regular schedule maintenance program is recommended.
SAFETY WARNING: Luminaire can become very hot depending on the lamp wattage used. Lens and housing around the lamp can become hot
enough to blister hands. Particular care should be taken not to locate luminaires where small children can reach them if high wattage lamps are
used.
NOTE: Always use UL recognized wire connectors for connections.
NOTE: Save these instructions for future reference.
LUMINAIRE IS UL LISTED FOR ABOVE GRADE INSTALLATION ONLY.
LUMINAIRE MOUNTING:
1. Make sure electrical supply is off at circuit breaker before starting
luminaire installation or servicing luminaire.
2. Thread luminaire onto junction box or other mounting device until it is
at desired direction using thread sealant. Tighten jam nut (provided) to
ensure the luminaire is locked to adjusted position.
3. Attach luminaire leads to line in leads observing polarity, black to
black, white to white and green to ground using silicone filled safety
connectors (provided).
4. Attach junction box cover with luminaire to junction box (by others).
Make sure not to pinch wires that may be sandwiched between cover
and box.
5. Coat exposed luminaire threads with thread sealant to keep moisture
from entering junction box or other mounting device.
6. To adjust luminaire aiming angle, loosen adjustable knuckle screw. Do
not disengage totally. Hold luminaire at selected angle and tighten
knuckle screw firmly.
7. Install lamp.
8. Coat all exposed screws with silicone grease.
9. Supply power to the luminaire and check for proper operation.
Vista Professional Outdoor Lighting reserves the right to modify the design and/or construction of the fixture shown without further notification.
1625 Surveyor Avenue • Simi Valley, CA 93063 • [phone] • (800) 766-VISTA (8478)
FAX: (888) 670-VISTA (8478) • [email protected] • www.vistapro.com

CAUTION: Do not exceed maximum wattage marked on
luminaire label.
1. To prevent electrical shock, disconnect from electrical
supply before service.
2. Loosen screw from shroud.
3. Remove shroud and gasket to expose lamp.
4. Replace lamp with correct wattage and type marked on
fixture label.
NOTE: DO NOT touch lamp with bare hands. Always use soft
cloth or the plastic wrapping (if available) to handle the
lamp.
5. Re-install shroud and gasket and tighten shroud screws.
LAMP INSTALLATION/REPLACEMENT:
1093 11.16
INSTALLATION INSTRUCTIONS
WARNING: TO REDUCE THE RISK OF FIRE, OR INJURY TO
PERSONS:
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamps get hot quickly! Contact only switch/plug when turning
on.
3. Do not touch hot lens, guard or enclosure.
4. Keep lamp away from material that may burn.
5. Do not touch the lamp at any time. Use a soft cloth. Oil from the
skin may damage lamp.
6. Do not operate luminaire fitting with a missing or damaged
cover.
IMPORTANT SAFETY INSTRUCTIONS - THE LIGHTED LAMP IS HOT!
SAVE THESE INSTRUCTIONS
(Leave with property owner/manager)
Vista Professional Outdoor Lighting reserves the right to modify the design and/or construction of the fixture shown without further notification.
1625 Surveyor Avenue • Simi Valley, CA 93063 • [phone] • (800) 766-VISTA (8478)
FAX: (888) 670-VISTA (8478) • [email protected] • www.vistapro.com
Up & Accent Lights
Architectural Series
1093