Vista VK2-108VRDIR37e User manual

Please read this manual thoroughly before use, and keep it handy for future reference.

Quick Installation Guide
VK2-1080VRDIR37e Quick Guide V1.0
2

Quick Installation Guide
VK2-1080VRDIR37e Quick Guide V1.0
3
1. Description
This manual applies to the VK2-1080VRDIR37e full HD Vandal resistant varifocal dome with IR
illumination.
• Installation Steps
Follow these steps to install the VK2-1080VRDIR37e on your local network (LAN):
1. Check the package contents against the list below.
2. Connect the VK2-1080VRDIR35V16e
3. Set an IP address.
4. Set the password.
• Package Component
The system comes with the following components:
Camera Unit Installation CD Installation Guide Accessory Kit Template sheet
Notes:
1. Check your package to make sure that you received the complete system, including all
components shown above.
2. Adapter for DC 12V is not supplied.
• Contents in the installation CD
1. The User’s Manual
2. The SmartManager User’s Manual
3. The VK2-Client User’s Manual
4. The SmartManager Installation software
5. The VK2-Client Installation software

Quick Installation Guide
VK2-1080VRDIR37e Quick Guide V1.0
4
• Connection Cable
Camera Dimension
See the diagrams below for the exact dimension
NO
Name
Description
1
Lens
Allows wide area to be monitored
2
Power Cable
Cable for Power source (DC 12V)
3
Ethernet Cable
Cable for Ethernet (POE)

Quick Installation Guide
VK2-1080VRDIR37e Quick Guide V1.0
5
2. Installation
2.1 Connection
• Camera Installation
Carefully remove the contents from the box, and verity that nothing was damaged in shipment.
1) Mark the screw hole positions on the ceiling or wall surface using the Template Sheet.
2) Disassemble the camera by removing the dome cover.
3) Mount the camera assembly using the Anchors (x2) and Screws (x2) to the surface of the
ceiling or wall
4) Reassemble the dome cover on the camera assembly. Turn Camera Cover clockwise to complete
installation
• Connecting to the RJ-45
Connect a standard RJ-45 cable to the network port of the network camera. Generally a
cross-over cable is used for directly connection to PC, while a direct cable is used for connection
to a hub or switch.
Micro SD memory slot
Insert the SD memory card.
• Connecting the Power
Connect the DC 12V power adaptor to the camera.
(This connection is not used if using PoE power)

Quick Installation Guide
VK2-1080VRDIR37e Quick Guide V1.0
6
2.2 Network Connection and IP assignment
The Camera supports the operation through the network. When a camera is first connected to the
network it has no assigned IP address. So, it is necessary to allocate an IP address to the device with
the “Smart Manager” utility found on the supplied CD. The factory default IP is “192.168.30.220”.
1. Connect the Camera / device to the network and power up.
2. Start SmartManager utility (Start>All programs>SmartManager>SmartManager), the main
window will be displayed, after a short while any network devices connected to the network will
be displayed in the list.
3. Select the camera on the list and click right button of the mouse. You can see the pop-up menu
below.
4. Select Assign IP. will see the "Assign IP Address" window. Enter the required IP address.
Note: For more information, refer to the Smart Manger User’s Manual.

Quick Installation Guide
VK2-1080VRDIR37e Quick Guide V1.0
7
3. Operation
The Camera can be used with Windows operating system and browsers. The recommended browsers
are Internet Explorer, Safari, Firefox, Opera and Google Chrome with Windows.
3.1 Access from a browser
1. Start a browser. (Internet Explorer) will be used in this example.
2. Enter the IP address or host name of the Camera in the Location/Address field of your browser.
3. You can see a starting page. Click Live View or Setup to enter web page.
4. The network camera’s Live View page appears in your browser.
3.2. Access from the internet
Access from the internet once connected, the Camera is accessible on your local network (LAN). To
access the Camera from the Internet you must configure your broadband router to allow incoming
data traffic to the network camera. To do this, enable the NAT-traversal feature, which will attempt to
automatically configure the router to allow access to the network camera. This is enabled from Setup
> System > Network > NAT.
For more information, please see “3.5.5 System>Network>NAT” of User’s Manual.

Quick Installation Guide
VK2-1080VRDIR37e Quick Guide V1.0
8
3.3 Setting the admin password over a secure connection
To gain access to the product, the password for
the default administrator user must be set. This
is done in the “Admin Password” dialog, which is
displayed when the Camera is accessed for the
setup at the first time. Enter your admin name
and password, set by the administrator.
Note: The default administrator username and
password is “admin”. If the password is lost, the
Camera must be reset to the factory default
settings. See “3.6 Resetting to the Factory
Default Settings”.
3.4 Live View Page
The live view page comes in several screen
modes:1920x1080, 1280x1024, 1280x720,
704x480(576),640x480,352x240(288) and
320x240. Users are allowed to select the
most suitable one out of those modes.
Please, adjust the mode in accordance with
your PC specifications and monitoring
purposes.
1) General controls
Live View Page Search & Playback Page Setup Page Help Page
The video drop-down list allows you to select a customized or pre-programmed
video stream on the live view page. Stream profiles are configured under Setup > Basic
Configuration > Video & Image. For more information, please see “3.5.1 Basic Configuration >
Video & Image” of User’s Manual.
The resolution drop-down list allows you to select the most suitable one
out of video resolutions to be displayed on live view page.
The protocol drop-down list allows you to select which combination of
protocols and methods to use depending on your viewing requirements, and on the properties of
your network.

Quick Installation Guide
VK2-1080VRDIR37e Quick Guide V1.0
9
2) Control toolbar
The live viewer toolbar is available in the web browser page only. It displays the following
buttons:
The Stop button stops the video stream being played. Pressing the key again toggles the
start and stop. The Start button connects to the Camera or start playing a video
stream.
The Pause button pause the video stream being played.
The Snapshot button takes a snapshot of the current image. The location where the
image is saved can be specified.
The digital zoom activates a zoom-in or zoom-out function for video image on the live
screen.
The Full Screen button causes the video image to fill the entire screen area. No other
windows will be visible. Press the 'Esc' button on the computer keyboard to cancel full
screen view.
The Manual Trigger button activates a pop-up window to manually start or stop the event.
3) Video Streams
The Camera provides several images and video stream formats. Your requirements and the
properties of your network will determine the type you use.
The Live View page in the Camera provides access to H.264, MPEG-4 and Motion JPEG video
streams, and to the list of available video streams. Other applications and clients can also access
these video streams/images directly, without going via the Live View page.
3.5 Camera Setup
This section describes how to configure the network camera, and is intended for product
Administrators, who have unrestricted access to all the Setup tools; and Operators, who have access
to the settings for Basic, Live View, Video & Image, Event, and System Configuration.
You can configure the Camera by clicking Setup in the top right-hand corner of the Live View page.
Click on this page to access the online help that explains the setup tools
When accessing the Camera for the first time, the “Admin
Password” dialog appears. Enter your admin name and
password, set by the administrator.
Note: If the password is lost, the Camera must be reset
to the factory default settings.
See “3.6 Resetting to the Factory Default Settings”.

Quick Installation Guide
VK2-1080VRDIR37e Quick Guide V1.0
10
3.6 Resetting to the factory default settings
To reset the Camera to the original factory settings, go to the Setup>System> Maintenance web page
(described in User’s Manual, “3.5.5 System > Maintenance”) or use the Reset button on the network
camera, as described below
• Using the Reset Button
Follow the instructions below to reset the Camera to the factory default settings using the Reset
button.
1. Switch off the Camera by disconnecting the power adapter.
2. Press and hold the Reset button with a straightened paperclip while reconnecting the power.
3. Keep the Reset button pressed for at least 2 or more seconds.
4. Release the Reset button.
5. The Camera resets to factory defaults and restarts after completing the factory
reset.
Caution: When performing a Factory Reset, you will lose any settings you have saved.
(Default IP 192.168.30.220)
3.7 More Information
For more information, please see the Camera User’s Manual, which is available on the CD included in
this package.
Reset Button

Quick Installation Guide
VK2-1080VRDIR37e Quick Guide V1.0
11

Quick Installation Guide
VK2-1080VRDIR37e Quick Guide V1.0
12
Printed in Korea