vitapur VWD266BLP User manual

Top Load
Water Dispenser
great taste, great health, great life.
Use & Care Guide
VWD266BLP
PLEASE READ THIS MANUAL THOROUGHLY
BEFORE USING THE APPLIANCE AND
KEEP IT FOR FUTURE REFERENCE
210614

Warning: This Product can expose you to chemicals including Diisononyl
phthalate (DINP) which is known to the State of California to cause
cancer and Di-isodecyl phthalates (DIDP) which is known to the State of
California to cause birth defects or other reproductive harm.
For more information go to: www.p65Warnings.ca.gov
After handling the electrical power cord, please wash your hands.
Safety Information
Important: Refrigerants must be handled and disposed of by qualified
service personnel only. Before discarding this water dispenser
to landfill, contact local authorities for advice on proper disposal
methods for refrigerants.
Warning: Always disconnect the power cord before attempting to
clean or move the dispenser.
Warning: Do not damage the refrigeration cooling system.
Warning: This water dispenser is designed for indoor applications only.
Warning: Never put anything flammable close to the dispenser.

Safety Information (continued)
Pre-Operation
1. Never turn the dispenser upside down or tilt it more than 45 degrees. If the unit
has been resting on its side for a long period of time, place the water dispenser in
the upright position for approximately 12 hours before turning it on.
2. For use with 3, 4 or 5 gallon (11, 15 or 19 liter) round type water bottles.
3. Never use this dispenser with water that is unsafe to drink or is from an unknown
source.
4. Never use any other liquid in the dispenser other than known and
microbiologically safe bottled water.
5. This water dispenser is equipped with a grounded power cord plug for your safety.
6. Keep your water dispenser in a dry place away from direct sunlight.
7. Leave a minimum of 2” (5 cm) around the back and sides of the dispenser for
proper ventilation.
8. Always install your water dispenser on a level floor. Wait 3 minutes before
restarting machine after shutting it down.
9. Always unplug the water dispenser before servicing.
10. Regular cleaning of your water dispenser is required for your warranty. Please
follow the cleaning instructions outlined in this manual and clean the dispenser
every 4 months.
2
1

Pre-Operation (continued)
GROUNDING PRECAUTIONS
ELECTRICAL REQUIREMENTS:
A 115 Volt, 60 Hz., AC only 15 amperes
fused, grounded electrical supply is
required. It is recommended that a
separate circuit serving only your Water
Dispenser be provided. Use an outlet
that cannot be turned o by a switch.
WARNING
WARNING
FAILURE TO FOLLOW THESE
INSTRUCTIONS CAN RESULT IN
DEATH, FIRE OR ELECTRICAL SHOCK
GROUNDING INSTRUCTIONS:
• Warning: This appliance must be grounded.
In the event of an electrical short circuit,
grounding reduces the risk of electric shock by
providing an escape wire for electric current.
• Warning: Improper use of the grounding plug
can result in a risk of property damage, electric
shock causing serious injury, even death.
• Warning: This appliance is equipped with
a power cord having a grounding wire with
a grounding plug and must be connected
into a properly grounded polarized outlet.
Consult a qualified electrician if the grounding
instructions are not completely understood, or
if doubt exists as to whether the wall outlet is
properly grounded.
• Warning: If the wall outlet is a standard 2
prong outlet, it is your personal responsibility
and obligation to have it replaced with a
properly grounded 3-prong wall outlet.
• Warning: Do not under any circumstances
cut or remove the third (ground) pin from the
power cord plug.
• Warning: Do not use adapter plugs or
extension cords with this appliance.
• Warning: If the power cord is too short, have a
qualified electrician install an electrical outlet
near the appliance.
• Warning: Do NOT use the appliance if the
power cord becomes frayed or otherwise
damaged.
SPECIFICATIONS
Model No. VWD266BLP
Dimensions W x D x H 10.8 in. x 11.7 in. x 36.5 in. • 27.5cm x 29.7cm x 92.7cm
Cooling Temp. Range 39 ˚F / 3.8 ˚C Based on colder water thermostat setting ( )
Power Consumption 80W

Pre-Operation (continued)
PACKAGE CONTENTS
1. Anti-Leak Bottle Support Collar
2. Cold Water Dispensing Button
3. Room Temperature Water Dispensing Button
4. Ready-to-Dispense Indicator Lights
5. Removable Drip Tray
6. Condenser Coils
7. Adjustable Cold Water Thermostat
8. Power Cord
1
3
4
5
2
6
7
8

Pre-Operation (continued)
0
m
Use Vitapur VCK50 Water
Dispenser Cleaner or combine
6 Cups (1.5 L) Hot Water with 2
Cups (0.5 L) Vinegar
1
5 6
42 3
INITIAL PRODUCT CLEANING OF RESERVOIRS
8 Cups (2L)
Fresh Hot Water Repeat Steps 5 - 6
7
910
8

Pre-Operation (continued)
Control Panel LED Light Functions
1
GREEN LED LIGHT
(POWER)
Solid Green “On” = Water dispenser power is on.
Solid Green “O” = Power cord not connected.
2
BLUE LED LIGHT
(COLD WATER)
Solid Blue “On” = optimum cold water temperature is ready for
dispensing.
Solid Blue “O” = cooling cycle is operating (compressor is on).
12
INSTALLING THE WATER BOTTLE
1 2
3 4 5

Operation
. DISPENSING COLD WATER
2 43
Going Away On Vacation
When not using the dispenser for long periods of time or when going on vacation,
to conserve energy, unplug the dispenser and drain the reservoirs (see Draining
the Reservoirs). Follow Initial Product Cleaning Procedures upon return and
startup of the dispenser.
1
The temperature of the cold water reservoir is monitored by a cold water
control located at the rear of the dispenser. Using a screwdriver, turn the
dial clockwise between lower setting ( ) for warmer water and higher
setting ( ) for colder water until the desired temperature is reached. If
water is not being properly dispensed, there could be possible ice build-up
in the reservoir due to the thermostat being set too cold. If this happens,
slowly rotate the thermostat set screw counterclockwise to a warmer setting.
NOTE: Any change to the cold water temperature control may eect Energy Star eiciency.
Adjusting the Cold Water Temperature:

1 1
2 2
Care and Cleaning
CLEANING THE OUTSIDE OF THE WATER DISPENSER
CLEANING THE DRIP TRAY
DRAINING THE RESERVOIRS
1 2 3 4
2 3 4
1
Soapy Water
Soapy Water
1 2
6
4
5
3
7

Troubleshooting
Note: Do not return this product to the store. For questions on operation, assembly or
parts, please contact Customer Service at 1-877-447-4768 and ask for assistance.
Problem Possible Cause Suggested Solution
Water dispenser
is leaking
Water was poured directly into
bottle support collar and
overowed.
Push down on dispenser buttons
to lower the water level.
Water is not hot
or cold enough
All the water in the tank has been
used.
Replace with full bottle and wait;
30 minutes for water to cool.
The unit is unplugged. Plug it into the outlet.
The circuit breaker in your home
has tripped or the fuse has blown.
Reset the breaker or replace the
fuse.
Thermostat needs to be adjusted. Using a screwdriver, turn the
dial clockwise between lower
setting ( ) for warmer water and
higher setting ( ) for colder water
until the desired temperature is
reached.
Water dispenser
is not dispensing
water
Empty water bottle. Replace with full bottle.
Mineral deposits clogging tanks. See Cleaning the Reservoirs.
Possible air pocket. Push down on the dispenser
buttons to prime the unit.
Possible ice build up due to
thermostat set too cold.
Unplug overnight, then reset. Set
the thermostat to lower setting ( ),
slowly increasing based on your
use and need for cold water.
Water dispenser
is noisy
Bottle is making a gurgling noise
as it fills the tank.
This is normal.
Water dispenser is uneven. Make sure the dispenser is on an
even surface that can support its
full weight.

Warranty
Do not return this product to the store: Please contact Customer Service at
1-877-447-4768.
The supplier warrants your water dispenser to be free from manufacturing defects
in workmanship or material under normal operating conditions for one (1) year
from the original date of purchase. This warranty applies only in the country in
which it is sold and is available to the original purchaser only. This warranty is
non-transferable.
This warranty and the CSA International listing for this water dispenser are void
if the water dispenser is altered, modified, or combined with any other machine
or device. Alteration of this water dispenser may cause serious flooding and/or
hazardous electrical shock or fire.
The provisions of this warranty shall not apply to:
• Water bottles
• Service trips to your home to teach you how to use the product
• Improper installation, delivery, or maintenance (Failure to maintain
the product according to the instructions outlined in the product manual
will automatically void the warranty.)
• Failure of the product due to abuse, misuse, alteration, commercial use,
or any use for which the product was not intended
• Products that are used outside a residential or oice environment
• Replacement of house fuses or resetting of circuit breakers
• Use of this product where water is microbiologically unsafe or of
unknown quality
• Damage to the product if used to dispense anything other than water
• Damage to the product caused by accident, fire, floods, or acts of God
• Any service to the product by unauthorized personnel
• Incidental or consequential damage caused by possible defects with this
appliance, its installation or repair
This warranty shall be fulfilled at an authorized repair facility. All warranty repairs
must be pre-authorized by the supplier. The supplier will, at its option, repair
or replace free of charge any defective part, where the purchaser has notified
their retailer within the warranty period. The obligation of the supplier under this
warranty is expressly limited to such repairs or replacement. This warranty does
not cover the freight costs to and from the authorized repair facility.
Except as set forth herein or required by law, the manufacturer makes no other
warranty, guarantee, or agreement, express, implied, or statutory, including any
implied warranty of merchantability or fitness for a particular purpose.

Warranty
The manufacturer does not assume or authorize any person to assume any
obligations of liability in connection with this water dispenser. In no event will the
manufacturer be liable for indirect, special, or consequential damages (including,
without limitation, economic loss) or for any delay in the performance of this
agreement due to causes beyond its control.
Some states or provinces do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you. Some states or provinces do
not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state or
from province to province.
If you require service, please first see the “Troubleshooting” section of this manual.
Additional assistance can be found by calling our customer service line at
1-877-447-4768, Monday to Friday from 8:00 a.m. to 4:30 p.m. (CST)
Keep this manual and your sales slip together for future reference. You must
provide proof of purchase for in-warranty service.
Write down the complete model number and serial number of your water dispenser
to better help you obtain assistance or service if your ever need it. You can find this
information on the back of the water dispenser.
Product Registration:
To register your product, please visit:
ghpgroupinc.com/product-registration.html and complete within (14) days of
purchase.

Product Notes

Distributeur d’eau
à chargement par le haut
bon goût, bonne santé, bonne vie.
Guide d’utilisation
et d’entretien
VEUILLEZ LIRE CE MANUEL ATTENTIVEMENT
AVANT D’UTILISER L’APPAREIL ET
CONSERVER CE MANUEL POUR
CONSULATATION ULTÉRIEURE
VWD266BLP

Renseignements de sécurité
Important : Les fluides frigorigènes doivent être manipulés et jetés uniquement
par du personnel de service qualifié. Avant de jeter ce distributeur d’eau au site
d’enfouissement, contactez les autorités locales pour obtenir des conseils sur les
méthodes d’élimination appropriées concernant les fluides frigorigènes.
Avertissement : Ne placez jamais de matière inflammable à proximité du
distributeur.
Avertissement : Ce distributeur d’eau est conçu pour des applications d’intérieur
seulement.
Avertissement : Ne pas endommager le système de réfrigération et de
climatisation.
Avertissement : Débranchez toujours le cordon d’alimentation avant de nettoyer
ou de déplacer le distributeur.
Avertissement : Ce produit peut vous exposer à des agents chimiques,
dont le phtalate de diisononyle (DINP), reconnu par l’État de Californie
comme pouvant causer le cancer, ainsi que les phtalates diisodécyle
(DIDP) reconnus par l’État de Californie comme pouvant causer des
anomalies congénitales et autres dommages au système reproducteur.
Pour plus de renseignements, visitez le www.p65Warnings.ca.gov
Après avoir touché le cordon électrique, veuillez vous laver les mains.

Pré-Opération
Renseignements de sécurité (suite)
1. Ne retournez jamais le distributeur d’eau et ne l’inclinez pas à plus de 45 degrés.
Si l’appareil est resté sur le côté pendant un long moment, placez le distributeur
d’eau à la verticale pendant 12 heures environ avant de le brancher.
2. S’utilise avec des bouteilles d’eau rondes de 3, 4 ou 5 gallons (12, 15 ou 19 litres).
3. N’employez jamais ce distributeur avec une eau qui n’est peut-être pas potable
ou qui provient d’une source inconnue.
4. N’employez jamais dans le distributeur d’autres liquides que de l’eau en bouteille
connue et microbiologiquement sûre.
5. Ce distributeur d’eau a une prise d’alimentation électrique avec mise à la terre
pour assurer votre sécurité.
6. Conservez votre distributeur d’eau à un endroit sec et non exposé aux rayons
solaires directs.
7. Laissez au moins 2 po (5 centimètres) derrière le distributeur et sur les côtés
pour avoir une ventilation appropriée.
8. Installez toujours le distributeur d’eau sur une surface au niveau qui peut soutenir
tout son poids.
9. Débranchez toujours le distributeur d’eau avant d’en faire l’entretien.
10. Un nettoyage régulier de votre distributeur d’eau est nécessaire pour que la
garantie soit applicable. Veuillez suivre les instructions de nettoyage de ce
manuel et nettoyer le distributeur tous les 4 mois.
2
1

Modèle VWD266BLP
Dimensions L x P x H 10,8 po. x 11,7 po. x 36,5 po. • 27,5cm x 29,7cm x 92,7cm
Écart de température de
refroidissement :
39 ˚F / 3.8 ˚C Basé sur le plus maximum réglage du
thermostat d’eau froide ( )
Consommation d’électricité 80W
Pré-Opération (suite)
FICHE TECHNIQUE
PRÉCAUTIONS DE MISE
À LA TERRE
EXIGENCES ÉLECTRIQUES :
Une alimentation électrique mise à la
terre de 115 V/60 Hz, CA, à 15 ampères
seulement, avec fusible est nécessaire.
Il est recommandé de prévoir un circuit
distinct pour alimenter uniquement
votre distributeur d’eau. Utilisez une
prise qui ne peut pas être désactivée
par un interrupteur.
AVERTISSEMENTS
AVERTISSEMENTS
LE NON-RESPECT DE CES
INSTRUCTIONS PEUT ENTRAÎNER
LA MORT, UN INCENDIE OU UN
CHOC ÉLECTRIQUE
INSTRUCTIONS DE MISE À LA TERRE:
• Avertissement : Cet appareil doit être mis à la terre.
En cas de court-circuit, la mise à la terre réduit les
risques de chocs électriques en procurant un chemin
d’évacuation du courant.
• Avertissement : Une utilisation inadéquate de la
fiche de mise à la terre peut entraîner des chocs
électriques, pouvant ainsi causer des blessures
graves, voire la mort.
• Avertissement : Cet appareil est doté d’un cordon
d’alimentation muni d’un conducteur de mise à
la terre et d’une fiche mise à la terre, et doit être
raccordé à une prise polarisée correctement mise à
la terre. Faites appel à un électricien qualifié si vous
ne comprenez pas parfaitement les instructions de
mise à la terre ou si vous avez des doutes sur la mise
à la terre adéquate de votre appareil.
• Avertissement : Si la prise de courant murale est une
prise standard à deux broches, il vous incombe de
la remplacer par une prise à trois broches mise à la
terre de façon adéquate.
• Avertissement : Ne coupez et ne retirez jamais la
broche de mise à la terre du cordon d’alimentation.
• Avertissement : N’utilisez pas d’adaptateurs ou de
rallonges avec cet appareil.
• Avertissement : Si le cordon d’alimentation est trop
court, demandez à un électricien qualifié d’installer
une prise de courant à proximité de l’appareil.
• Avertissement : N’utilisez PAS l’appareil si le cordon
d’alimentation est eiloché ou endommagé.

Pré-Opération (suite)
CONTENU DE LA TROUSSE
1. Collier de soutien de la bouteille
2. Bouton de distribution d’eau froide
3. Bouton de distribution d’eau ambiente
4. Prêt-à distribuer voyants
5. Plateau égouttoir amovible
6. Serpentin du condenseur
7. Thermostat réglable d’eau froide
8. Cordon d’électricité
1
3
4
5
2
6
7
8

Pré-Opération (suite)
Utilisez le nettoyant pour
distributeur d’eau Vitapur
VCK50 ou combinez 6 tasses
(1,5 L) d’eau chaude avec 2
tasses (0,5 L) de vinaigre
NETTOYAGE INITIAL DES RÉSERVOIRS
8 tasses (2L)
eau fraîche et chaude
0
m
1
5 6
42 3
répétez les étapes 5 - 6
7
910
8

Fonctions de voyant DEL du panneau de commande
1
VOYANT DEL VERT
(SOUS TENSION)
Vert fixe «Allumé en continu» = le distributeur d’eau est activé.
Vert fixe «Éteint» = Cordon d’alimentation non connecté.
2
VOYANT DEL BLEU
(EAU FROIDE)
Bleu fixe «Allumé en continu» = la température optimale de l’eau
froide est prête pour la distribution.
Bleu fixe «Éteint» = le cycle de refroidissement fonctionne (le
compresseur est en marche).
Pré-Opération (suite)
INSTALLATION DE LA BOUTEILLE DE L’EAU
1 2
3 4 5
12