Vitek TRANSCENDENT VTC-TNB4LPRN User manual

VITEK
VITEK
VTC-TNB4LPRN
Transcendent Series
4 MegaPixel License Plate
Recognition WDR IP Motorized
Bullet Camera
QUICK START GUIDE
FEATURES:
•1/1.8” 4 MegaPixel Progressive Scan CMOS Sensor
•Advanced Starlight Technology Offers Dramatically Higher Sensitivity to Light Producing
Color Images in Very Dark & Night Scenes
• Up to 30fps live view @ 4 MegaPixel (2592 × 1520)
• 8~32mm @F1.6 Motorized Varifocal Lens
• Matrix IR (up to 325’ IR Range)
• True Wide Dynamic Range (120dB)
• True Mechanical Day / Night function by ICR
• XD-DNR (3D & 2D-DNR) Noise Reduction
• Intelligent Analytics: License Plate Recognition, Vehicle Type Detection, Video Exception
• 10,000 Vehicle Plate Database
• 0-75m/h (120km/h) Capture Speed (Dependant on Installation)
• Overlay Options: Time, Location, License Plate Information
•Triple Streaming: H.265+ / H.265 / H.264+ / H.264 / MJPEG
• 1 Ch. Audio In + 1 Ch. Audio Out*
• 1 Ch. Alarm In + 1 Ch. Alarm Out, 1 Ch. CVBS
• Supports Wiegand Protocol for Advanced Access Control Integrations
• Remote Viewing via VMS, Web Browsers, and iOS & Android Apps
• MicroSD Card Slot for Local Recording (256GB)
• IP67 Weather Resistance
• Wall Mount Included, Optional Mounts: Junction Box VT-TJB01
[See Additional Mounting Options on pg. 12]
• 12VDC / 24VAC [Dual Voltage] & PoE (Power over Ethernet) Operation Options
[See Power Supply Options on pg. 13]
• 3-Year Warranty
*Please research local, state and federal laws regarding audio surveillance.
PLEASE NOTE:
Complete User Guide, Software, Tools, and Updates are
available online. Scan the QR Code or visit:
http://www.vitekcctv.com/Downloads

2 3
Components and Accessories
Overview
Hex Wrench Anchors
* The weather resistant security cap is necessary for outdoor installation.
* If PoE is used to power the camera, 12VDC/24VAC power supply is not required.
[SEE PG. 13 FOR LIST OF SUGGESTED POWER SUPPLIES FOR THIS MODEL]
* Press and hold the reset button for over 10 seconds to restore factory settings.

3
Cable Connections
Weather Resistant Network Coupler
First connect the weather resistant cap to an ethernet patch cable,
then connect the cameras ethernet adaptor. If not powering the
camera with PoE, also connect the power cable to an approved
12VDC power supply.
1. Loosen the nut from the Weather Resistant Network Coupler,
2. Run ethernet cable through coupler, then attach a RJ-45 connector.
3. Tighten the nut and coupler for a weather resistant seal.
weather resistant cap

4 5
Installation
Before beginning installation, make sure that the wall or ceiling is strong
enough to withstand 3 times the weight of the camera. The mounting steps
are as follows:
Connecting Alarm Input / Output
Install the MicroSD Card

5
1. Attach the drill template to the
place where you want to install
the camera, then drill 4 screw
holes and 1 cable hole (if you
want to route the cables through
the mounting base) according to
the drill template.
2. Route the cables and connect the power & video cables, use the rubber plug
to fill the gap of the mounting base, then secure the mounting base to the
ceiling or wall with screws.
2.54”
2.54”
.2”
**Refer to pg 3 for Weather Resistance Cap instructions.

6 7
3. Loosen the screws to adjust the viewing angle of the camera. After that,
tighten the screws. Before adjustment, view the image of the camera on a
monitor.
4. Press the T or W button to obtain an optimum image.
5. Finally, re-install the cover.
**Refer to pg 3 for Weather Resistance Cap instructions.

7
LAN Configuration
The camera can be accessed on the local network either using the
IP-Tool or directly in a web browser.
Accessing the Camera Using the IP-Tool
1. Make sure the camera and PC are connected to the LAN.
2. Locate the IP-Tool installer at www.
vitekcctv.com/Downloads/Soft-
ware/Transcendent-IPTool.zip
, then install on the PC. Open
the installed application.
3. Modify the IP address. The default IP address is 192.168.226.201.
Click the information of the camera listed in the above table to show
the network information on the right side. Modify the IP address and
gateway of the camera and make sure its network address is in the
same local network segment as the computer’s. Please modify the
IP address of your device according to the practical situation.
For example, the IP address of your computer
is 192.168.13.4. So the IP address of the
camera should be changed to 192.168.13.X.
After modifying, please input the password
of the administrator and click “Modify” button
to modify the setting.
** Default admin password: “123456".
MENU
IP Camera
Network Cable Network Cable
Switch
Router Computer

8 9
4. Double-click the IP address and then the system will pop up the web
browser to connect IP-CAM . IE browser will download the Active X
control. After downloading, a login window will pop up as shown
below:
Input the user name and password to log in.
Default user name: admin / Default password: 123456.
Directly Access Through a Web Browser
The default network settings are as shown below:
IP address: 192.168.226.201 HTTP: 80
Subnet Mask: 255.255.255.0 Data Port: 9008
Gateway: 192.168.226.1
You may use the above default settings when you log in the camera for
the first time.
1. Manually set the IP address of the PC. The network segment should
be the same as the default settings of IP-CAM. Open the network
and share center. Click “Local Area Connection” to pop up the
following window.
Select “Properties” and then select Internet protocol according to the
actual situation (for example: IPV4). Next, click “Properties” button to
set the network of the PC.

9
2. Open the IE Browser and input the default address of IP-CAM and
confirm. The IE browser will download an Active X control.
3. After downloading the Active X control, the login dialog box will pop up.
4. Input the default username and password and then enter to view.
WAN Configuration
Access the camera by the router or virtual server for example.
1. Make sure the camera is connected to the LAN; Then log into the
camera via LAN and go to System Congfig→Network Config→Port
menu to set up the port number.
2. Enter System Config→Network Config→IP Address menu to modify
the IP address.
4. Open the web browser and input its WAN IP and HTTP port to
access the IP-CAM.
3. Go to the router’s management interface through IE browser to
forward the IP address and port of IP-CAM in the “Virtual Server”.
5. For additional setup, features and functions, please scan the
QR code on the front page of this quick guide and download
the complete manual.

10 11
DETAILED SPECIFICATIONS: VTC-TNB4LRPN
Image Sensor 1/1/8” 4.0 Megapixel Progressive Scan CMOS
Image Size 4 MegaPixel (2560 × 1520)
Electronic Shutter Manual or Auto, Manual: 1 / 1 s ~ 1 / 100000s
Resolution 4 MP (2592 × 1520) / 3 MP (2304 × 1296) / 1080P (1920 × 1080) / 720P (1280 × 720) / D1/CIF (480 × 240)
Min. Illumination 0.001 [email protected], AGC ON, 0 lux with IR
Lens 8~32mm Mtrzd Varifocal @F1.6, motorized
FOV Horizontal: 41°~15.5°, Vertical: 23°~9.5°, Diagonal: 46.5°~18°
Lens Mount Integrated
Recommended ANPR 23~99' (7-30M)
Other Features BLC, HLC, Defog
WDR 120dB True WDR
DNR XD DNR (3D-DNR / 2D-DNR)
S/N Ratio >50Db
Angle Adjustment Pan: 0°~360°, Tilt:0°~90°, Rotation: 0°~360°
IR Matrix (4)
IR Distance 325'
Video Compression Main stream: H.265+ / H.265 / H.264+ / H.264 Sub stream: H.265+ / H.265 / H.264+ / H.264 / MJPEG
Third stream: H.265+ / H.265 / H.264+ / H.264 / MJPEG
Main Stream 4MP/2K/3MP/1080P (60Hz :1 ~ 30fps; 50Hz : 1 ~ 25fps)
HFR Mode: 1080P/720P (60Hz: 1~60fps; 50Hz: 1~50fps)
Sub Stream 720P/D1/CIF ( 60Hz:1 ~ 30fps, 50Hz: 1 ~ 25fps )
Third Stream D1/CIF ( 60Hz:1 ~ 30fps, 50Hz: 1 ~ 25fps )
Bit Rate 64 Kbps ~ 8 Mbps
Bit Rate Type VBR / CBR
Audio Compression G.711A / G.711U
Image Settings ROI, Saturation, Brightness, Hue, Contrast,Wide Dynamic, Sharpness, Image Mirror, Image Flip,
Noise Reduction - Image Settings Adjustable through Client Software or Web Browser
ROI Each ROI to be configured separately
Network 100M RJ 45
Video Output CVBS Output (BNC × 1)
Audio 1CH Audio Input, 1CH Audio Output*
*Please research local, state and federal laws regarding the implementation of audio surveillance.