Vitrek V7 Series Installation and operation manual

ViTREK
V7X SERIES
OPERATING & MAINTENANCE MANUAL

V7X Series Operating Manual - November 21, 2012
SECTION 1 –PRODUCT INFORMATION
FEATURES
Easy to Use
o4.3" High Resolution Color Touch Display - Intuitive Graphical User Interface
oLarge High Reliability START and STOP switches
oLarge easy to see PASS/FAIL Indicators
Easy to Own
oLow Cost of Ownership - 2 Year Calibration Interval, 2 Year Parts & Labor Warranty
oIn-Field Updating of Firmware
oCompact and Lightweight
oOnly consumes 5W when not testing
High Quality
oMade in the USA - Designed & Built in San Diego CA
Reliable
oRugged Construction
oFan free, vent free Design
oHigh Efficiency Switch-Mode Drive with low temperature rise
Full Function
oFast (100ms min test time) and Accurate (1%)
o5 Functions - AC/DC Hipot, Insulation Resistance, Ground Bond & Low Resistance
5KV AC/DC Hipot, 20mA max source current, 100nA Leakage Current Resolution
Continuously Variable Insulation Resistance 20-5000V up to 450GΩ
Ground Bond 1-30A RMS, 100µΩ Resolution
Wide range (0 to 60KΩ) low resistance measurements with 1mΩresolution
oRamped Discharge Capability
oSelectable ARC Detection
oMulti-Mode IR with Steady or Rising Pass Mode
oAble to test either grounded or non-grounded DUTs
oWide range of capacitive loads can be tested (up to several µF)
Built-In Verification
oCompletely Internal Self-Test Fully Exercises Output and Verifies Current Accuracy
oPre-Programmed Daily Verification Test With Optional PVD Test Load
Safe
o150µs Safety Shutdown
oAutomatic DUT Discharge
oMeets UL, CSA, IEC Safety Tester Requirements
oCE Safety Mark Certified to EN61010
Equally at home in simple and complex systems
oUSB 2.0, Serial RS232 and Digital I/O Interfaces are Standard
oAble to be used in Complex Multi-Point Scanning Systems
oTest Memory Stores up to 999 Steps and 60 Test Sequences which can be named by the user
oTest steps for on-screen prompted user actions
oOn-screen review of complete test results for every test step
AVAILABLE MODELS, OPTIONS, SOFTWARE AND ACCESSORIES
MODELS
All models have USB 2.0, Serial RS232, Digital I/O and External Switch System (VICL) interfaces as standard.

V7X Series Operating Manual - November 21, 2012
V70. ACW and CONT modes.
V71. ACW, DCW and CONT modes.
V73. ACW, DCW, IR and CONT modes.
V74. ACW, DCW, IR, CONT and GB modes.
V79. CONT and GB modes.
OPTIONS
V7X-230V. Factory Set 230V Line Operation.
RPOO-7. Rear Panel Mounted Terminals instead of standard Front Panel Terminals.
SOFTWARE
QTV Pro-7. A 45 day free trial included with each unit. This software provides-
The user does not need to write software to use the V7X with a computer.
Can control testing using very complex switching systems when used with ViTREK 964 Switch Matrix units.
Easy to use fully graphical interface on a Windows based computer.
Multi-level user login, enabling the configuration of tests to be locked except for certain users.
Company wide use of test sequences using the company network.
Test sequences can be downloaded into the V7X and run without the computer.
Test results recorded on a computer or on the company network.
Computer generated multi-level test reports.
Compatibility with a wide range of Windows versions (Windows XP through Windows 8 as a Desktop
Application).
Upwards Compatibility to other ViTREK products.
Easy upgrade for users with ViTREK V6X and V4 products and QTPro-V software.
ACCESSORIES
TL-115-7. 115V Receptacle Hipot Test Adaptor
TL-115-7GB. 115V Receptacle Hipot and Ground Bond Test Adaptor
TL-IEC-95. IEC320 Power Socket Lead set for HiPot
TL-IEC-GBR. IEC320 Power Socket Lead set for HiPot and Ground Bond
TL-209. HV/CONT Test Lead Set (one supplied with each unit).
K-2R. Ground Bond Test Lead Set (one supplied with each V74 and V79).
HVW-7. High Voltage Warning Light.
RS-2. 6ft RS232 cable (V7X to Computer).
USB-1. 6ft USB 2.0 A-B Cable (V7X to Computer).
RSS-7. Remote Start Switch.
RSF-7. Remote Start Footswitch.
DIO-X2. Allows multiple accessories to be connected to the Digital I/O port.

V7X Series Operating Manual - November 21, 2012
RM-7. Rack mount kit for the V7X.
APVD-7X. PVD for performing automatic HiPot and Low Resistance verification tests.
APVD-74. PVD for performing automatic HiPot, Low Resistance and Ground Bond verification tests.