Vivanco FMC 4000 User manual

‘.’ :
i(
,: :
:
.:
Vivanco GmbH - Ewige Weide 15. D-22926 Ahrensburg - Fax [phone]
. .
,. . . .
-,
,‘,;,‘,.{.
., (
(_ :
.;: ::i:
. .
.’
;:, .!‘;‘j:
“:i>: :
: !,,.I;‘! i
8:: “: :
,.

0
GB Instruction manual for the radio microphone FMC 4000
I. Contents included in the set
Please check the contents of the box with the list below. Should any parts be missing please contact your
dealer.
(A) 1 x handheld microphone with built-in transmitter
(B) 1 x receiver
(C )I x 12 V plug-in power supply unit
(D) 1 x audio lead
(E) 1 x 9 V battery for the microphone (PP3 type)
(F) 1 x small screwdriver
2. Operating elements
(A) Handheld microphone (1) - (4)
(1) On/Off switch
(2) Battery status indicator lamp
(3) Frequency adjustment control
(4) Battery compartment
(B) Reception unit (5) - (9)
(5) Reception lamp
(6) Audio output socket
(7) Squelch control
(8) Channel select switch
(9) Low voltage socket
3. Settinu uu
3.1. Microphone
1. First open the battery compartment (4) by turning the sealing cap anti-clockwise.
2. Insert the battery which is loose until the screw cap is securely fitted. The correct polarity is marked
inside the compartment.
3. Close the battery compartment by placing the sealing cap into the thread and turning it clockwise. The
battery will now be fixed automatically.
4. Switch the microphone on with the On/Off switch (1). The battery indicator control lamp (2) comes on
brielly. It it stays on it signals that the battery is discharged. You should then replace the battery.
5. The appliance should always be switched off when not in use to save the battery. When not in use for
longer periods, the battery must be removed, otherwise there is a danger of the battery leaking and
damaging the microphone.
Consider the environment: Please do not throw used batteries away with your domestic rubbish but hand
them in at your nearest collection point. If you are going to use the microphone set frequently, we recommend
using a rechargeable battery pack, A suitable recharger is supplied by Vivanco. Please ask you dealer.
6
..:,.:
:,.
$
; .‘:
. .
.:
i :
i...
;I:.:
:. (
: :,,:
::_
:,;‘:i.;.; i.
: : ;a:
;
,:: ;y:j; : ‘..
s:‘,
3.2. Reception unit
1. First connect the 12 Volt plug-in power supply unit (C ) to the low voltage socket (9). Then connect the
plug-in power supply unit to the mains supply (230 V I50 Hz).
2. Then connect the audio lead (D) to the audio output socket (6) on the receiver. Connect the other end to
the microphone input socket of your hi-fi appliance (amplifier tape deck etc.). If your hi-fi appliance does
not have any microphone socket please ask your dealer for support.
3. To achieve the microphone range given, the aerial must be fully extended and as vertical as possible.
3.3. Tuning the microphone and reception unit
1. First ensure that your hi-fi appliance is set up correctly (input select, volume control etc.).
2. Then switch on the microphone and watch the reception lamp (5) at the reception unit. Tune with the small
screwdriver (F) the frequency adjustment control (3) at the microphone until the reception lamp comes
on. Your microphone set is now tuned and ready for use.
3. If the reception is disturbed or if you want to use 2 microphones at the same time, you can select another
channel at the reception unit. Use channel selection switch (8) and proceed as described in step 2. Impor-
tant: we recommend not to use more than 2 microphones at the same time.
4. If the microphone is switched off or the distance between the microphone and the reception unit is too
far distorsion may appear. By adjustment of of the squelch control (7) with the small screwdriver (F)
you can minimize this.
4. Trouble Shootinq
Problem Solution
No Sound Please make sure that
- the On/Off switch is in ,,On” position
- the battery / batteryx pack is in a good condition (lamp 2)
- the battery is fitting correctly
- your hi-fi appliance is switched on and set to microphone input
- microphone is correctly tuned to the receiver unit
- In some cases, it may be necessary to alter the position of the receiver horizontally
and/or vertically.
Sound interference - Select another channel
- Adjust the squelch control
- Switch off other radio frequency devices in your home (rf headphone, t-f alarm system
etc.)
- Check the connections (loose contact)
- Check the condition of the battery / battery pack.
If you are not able to solve the problem please ask your dealer for support.
7