VIVID STORM S User manual

请勿直接接触幕面
S Electric Tab-Tension Floor Screen
USER MANUAL
电动地升黑栅幕
S PRO/S PRO P Electric Tab-Tension Floor Screen
Electric Tab-Tension Floor Screen
USER MANUAL

Content
The Introduction Of Product
--------------------------5
Appearance---------------------------------------------5
Important Safety Precautions -----------------------9
Matters Needing Attention -------------------------10
Precautions for Use ---------------------------------11 Matters Concerning Projection --------------------11
Projected Area ---------------------------------------11
About Screen Performance -------------------------12
Installation Warning ----------------------------------13
Before pre installation ------------------------------13
Hardware Parts List ---------------------------------13
Ground Installation -----------------------------------14
Wall Installation ---------------------------------------15
Screen Running ----------------------------------------16
Manual Switch ----------------------------------------16
Remote control ---------------------------------------17
Screen Hight Limit Setting --------------------------20
Screen Maintenance ----------------------------------24
Manufacturer's Warranty ----------------------------25
Certificate -----------------------------------------------27
Product Warranty Card -------------------------------27
To Users
---------------------------------------------------2
Safety Instructions -------------------------------------2
Packing Contact-----------------------------------------4
Certificate ------------------------------------------------8
Black border down
(Lower the fixed height of the screen) ---20
--------22 Black border up (Raise the fixed height of the screen)

2
To Users
Thank you for choosing the VIVIDSTORM projection screen.
Please read this manual carefully before using the product and keep it properly.
The manual of products, accessories, user interface, etc. in this description are schematic diagrams and are for reference only. Due to
product updates, the actual product may be slightly different from the schematic diagram, please refer to the actual product.
Safety Instructions
Safety Instructions
For your security and interest, to ensure safe and correct use of this product, always comply with the following precautions to avoid
dangerous situations and damage to your unit:
Earth Terminal Ground Symbol
This refers to using this product needs electrical grounding.
Shipping Instructions
Please use this product's original packaging or same materials to
transport this product.
This symbol reminds the user to stay away from the inside of
the housing, especially during operation.
This symbol reminds users not to throw sundries into
the housing inside to avoid mechanical damage to the screen.
This symbol warns the user that uninsulated voltages within
thebody of this product may be sufficient to cause an electric
shock, therefore, any form of contact with any part within the
body is a risk of electric shock.
This symbol reminds the user to some important information
related to operation and maintenance.
Please read this information carefully to avoid incorrect operation.
Do not place the equipment near fireplaces or high
temperature objects such as gas stoves, barbecue or heaters;
Keep children and pet away from the product.
All items that are not product parts should be kept away
from moving parts.
This symbol reminds the user prevent hands or other body parts
from entering the inside of the bracket, causing hand pinching;

3
To prevent electric shock, fire hazard.
- Using incorrect cables may affect product performance, and may even lead to electric shock, fire and other accidents. In
order to ensure product performance and safety, please use the same type of cable as the original cable.
- If a power extension cord is required, use a power cord with an amperage rating not lower than that of the product.
Otherwise, it may cause the power cord to overheat, and even cause electric shock, fire and other accidents.
- In thunderstorm weather or when the product is not used for a long time, please unplug the power plug from the socket to
avoid damage to the device caused by lightning or power line surges.
- Do not place flammable objects near this product to avoid fire.
Instructions for safe operation
- Never place the screen in an unstable location, bracket or table, to prevent the product from falling, causing serious
equipment damage and personal injury.
- Do not attempt to disassemble this product, there are dangerous high voltages inside that could cause personal injury.
When repair is required, it must be done by trained or authorized service personnel.
- Do not place this product upright as it may tip over and cause damage.
-Make sure the product protected from rain and moisture.
- Do not immerse or expose this product to water or other liquids. If any liquid or solid object enters the cabinet, please unplug
the power cord of the device immediately and ask professional service technicians to check it before continuing to use it.
- Do not place this product in the following environments:
●Poor ventilation or narrow spaces. ●Near any device that generates a strong magnetic field. ●Direct sunlight.
●Extremely hot, cold or humid environment.

4
Packing Contact
When opening the box, check the contents of the box the list below. If there is any omission, please contact the dealer in time.
安全标识说明
黑栅幕布专用清洁刷
左侧两个配件均为赠品
不在保修范围内。.
清洁黏胶
Power cordProjection screen
Adjust Rod
(soft and hard)
Small screws for
bottom fixed base
Special cleaning
brush for UST ALR
screen material(gift)
Cleaning stickers
for UST ALR screen
material(gift)
Notice:
- Parking contact will be different for different countries (regions),
Please refer to the actual item.
- Please keep the original packaging for future shipments.
- Gifts are not covered under warranty.
- In special cases, the battery will be taken out before transported.
(Please contact the seller to inquire about the situation)
User manual+Envelopes
8Special cleaning brush for UST ALR
screen material(gift) 1
9Cleaning stickers for UST ALR
screen material(gift) 1
(IR)Infrared remote
control (includes wall
mount accessory)
RF wireless remote
(includes wall
mount accessory)
NO. Accessories Name Quantity（pcs）
1
2
3
4
5
6
7
Projection screen
User manual+Envelopes
Power cord
Adjust Rod(soft and hard)
Small screws for bottom fixed base
1
1
1
1
1
2
4
(IR)Infrared remote control
(Contains 2 button cell battery)
(includes wall mount accessory)
RF wireless remote
(Contains 2 button cell battery)
(includes wall mount accessory)
S Ele ctric Tab -Tens ion F loor Sc reen
USER MANUAL

5
The Introduction Of Product
Appearance
Housing
Rotatable bracket
Power cord
Screen material
Tab-Tension
Upper Cover
Support bar
(Screen close- top view)
(Screen open - front view) (Screen open- rear view)
Housing Adjust Holes Upper Cover
(Screen close - bottom image)
HousingRotatable bracket Rubber mat
The white area is the
standard projected area The black area is the non-projected area
Bottom Black
border

6
Appearance
(Screen close - back view)
(Screen close - front view)
Housing
Housing
Upper Cover
Rotatable bracket
Screws
Housing
(Screen open- right view)
Support bar
Screen manual switch
Power Switch
Infrared receiver outlet hole
Power cord socket
(Screen open - left view)
Screen material
(Screen close - front view) (Screen close - back view)
Rotatable bracket
Rotatable bracket

7
Appearance
IR receiver
Power cord socket
Power Switch
Screen manual switch
Schematic diagram of left end cover
Housing
Upper cover
Screen material
Screen Black border

8
VDE
安规认证
德国
D
V
E
*The right to interpret the above certification belongs to our company
Certificate
REA CH
Pilot lamp
- In the left picture (picture 1), when the red light is on, it is
working normally. If the red light or the green light is
flashing, it is the code matching and abnormal situation,
please contact the after-sales support.
- In the left picture (picture 2), make sure that the power
cord plug is inserted into the product socket. After turning
on the red power switch, the red light is on to indicate the
power-on state; when the power switch is turned off and
the red light is off, it is the poweroff state;
(Picture 1)
IR receiver
Power cord socket
Power Switch
Screen manual switch
(Picture 2)
Pilot lamp Power lamp, make the following prompts
for the working status:

9
Important Safety Precautions
Please read all the contents of the user guide carefully
and follow the operation steps below.
For reference when necessary, please keep this user guide.
1. In order to avoid damage to the equipment, please prohibit the use of any accessories not authorized by the manufacturer.
2. Be sure to handle the products carefully during transportation, so as to prevent product damage caused by collision.
3. In order to ensure the personal safety of the user and realize the reliable operation of the equipment, please make sure to
use the power cord provided by the equipment to connect the power supply for charging.
4. Please place the device close to the power socket to connect the power supply for charging.
5. You need to place the product properly. Please do not place any heavy objects on the power cord and screen to avoid danger
or operation obstacles.
6. In order to avoid electric shock, short circuit or fire caused by loose plug, please use the power cord correctly.
7. Since this product is equipped with a V-spring support system with strong tension, removing the screen without permission
will bring certain risks. Please do not disassemble the screen by yourself. In case of machine failure caused by your improper
operation, the seller and the manufacturer have the right not to be responsible for replace the product. In case of personal
injury, no liability shall be assumed.
8. The tubular motor on the electric screen of this product has a temperature control sensor with overheating protection
mechanism. If the screen runs up and down continuously for One and a half minutes, the motor will rest for more than 30
minutes.in order to prevent the motor from overheating and damage,If the motor stops operation due to the start of
overheat protection mechanism, please turn off the power and wait for 30 minutes to 2 hours until the motor cools down.
9.The remote control supplied with this product contains coin / button cell battery. If the coin / button cell battery is swallowed,
it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If
the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries
might have been swallowed or placed inside any part of the body, seek immediate medical attention.

10
Matters Needing Attention
No one is allowed to open the inside of the equipment and repair the product without authorization, except for the authorized
technicians.
1. Please make sure that the power supply connected to this product has stable current.
2. If you need to use the extension cord for this product, please make sure that the power cord rating of the extension cord is the
same as that of this product, so as to avoid equipment damage due to overheating.
3. When your hands and feet are in contact with water, do not operate the power plug in this case.
4. When you encounter heavy rain, wind, thunder or lightning in the process of using this product, please be sure to disconnect
the power line.
5. The curtain of this product should not be placed in direct sunlight, rain and humid environment.
6. In order to prevent the product from overheating, keep away from fire source and high temperature equipment when using
this product. At the same time, the power supply of this product should be cut off before transportation or maintenance.
7. Like any other household appliances, when this product is not used for a long time, please completely disconnect the power
supply to ensure safety.
8. If there is any obvious damage to any parts of the product, in order to avoid any injury and electric shock, please do not
continue to use.
9. When installing in the residential and commercial buildings, users should provide reasonable protection for the products to
prevent the radiated RF energy from interfering with the operation of the products. However, there is no guarantee that the
product will not be disturbed in special installation.
*Notice:
·Do not to throw sundries into the housing inside to
avoid mechanical damage to the screen;
·The seller and the manufacturer are not responsible
for any damage to the equipment caused by this;
·Before the screen is turned off, please make sure
that there is no sundries in the cover.
Matters Needing Attention
Warning! If you do not strictly follow the prescribed precautions during use, this may lead to equipment
damage and other unnecessary damage.
Please observe the family fire safety regulations; do not place the equipment near the fireplace or high
temperature objects such as gas stove, barbecue or heater to avoid equipment damage.
Please keep this product out of the reach of children.
Do not put your hands
into the cover of the product
Do not place the equipment near
the fireplace or high temperature objects
such as gas stove, barbecue or heater
Keep children away
from the product
Moving parts!Keep body parts
away from moving parts.

11
Matters Concerning Projection
Projected Area
1.Please project according to the actual projection size of the screen purchased when using the projector.
2.Since the position of black border has been preset on the screen of this product, please do not exceed the specified projected
area during projection. You should note that the default black border is not the projection area.
Classic product design:
Screen with black border
size

12
About Screen Performance
1.Please note that when placing this product, please make sure that the product is always in a horizontal state. Do not place the
screen in an inclined or vertical position.
2. After using for a period of time, if the cover on both ends of the screen is slightly tilted, there is no need to worry. This is a
normal phenomenon and does not affect the viewing and use. In addition, due to the cover warping, there is a gap between the
screen and the housing case after closing, which is also a normal phenomenon.
3.If there are regular creases on the screen surface after the screen is opened, don't worry. This is a normal phenomenon.
It is caused by the screen being curled and tightened for a long time, which does not affect the user's viewing. After
opening the screen for a period of time, you will notice that the stripes on the screen will gradually disappear.
Please make sure the product
is placed horizontally
There was a slight tilt after
the screen was closed

13
Installation Warning
Before pre installation
1. When you open the package, please carefully open the screen package to avoid the product from rubbing or falling.
2. Please always place the screen in a horizontal position. Do not install the product on an uneven or inclined surface.
3. Please keep the screen away from dust, sawdust and liquid to protect the screen from contamination.
Since the installation environment of each user is different, the instructions in this user guide are only for reference. If you
need further installation and safety suggestions, please consult the professional installation company. It should be noted that
no matter what kind of installation method you take, the product should not be loosened or dropped due to vibration or tension,
so as to keep the product stable. The installation personnel of the product must ensure that the bracket accessories used have
sufficient strength to support the product and select the appropriate installation position.
Hardware Parts List
Before you install the product, make sure that all parts of the product are included. Please note that the screws supplied
with this product may not be suitable for all mounting surfaces. Please consult the professional installation personnel or
hardware store to get the correct installation screws and anchors.

14
Ground Installation
Safety tips: it is recommended that two people lift the product and place it horizontally.
1. When using this product, you can place the product on the horizontal ground and fix it. Before placing the product, please pay
attention to cleaning the ground debris to keep the floor dry.
2. When using and rotate the four bottom supports, rotate the four bottom supports, one of which can be selected to fix the
bracket according to the actual situation. It is recommended to use screws to fix the product on the ground.
Rotatable bracket
Rotatable bracket

15
Wall Installation (The wall hanger can be used as a reference If additional purchase it)
1. If you purchase the wall brackets, you can fix the product screen on the wall.
2. When installing the product, first you need to make a horizontal mark on the wall and mark the hole position, and then fix the
wall brackets on the wall. It should be noted that when lifting the product, two people should lift and place it on the rack at the
same time.
Wall brackets accessories Schematic diagram of wall
brackets accessories
Diagram on the front
of the screen

16
Screen Running
1.Manual Switch
Voltage information: make sure your screen is working at the depending on the area.correct voltage,
(1) Plug the screen power cord into the correct power outlet.
(2) When the product power is turned on, a "beep" sound will be emitted for 1.5 seconds, indicating that the product has
been powered on.
(3) When the screen is fully raised, you can choose to turn off the power switch and unplug the power cord due to long-term
viewing. At this time, the screen will remain open and will not be closed due to power off. To turn off the screen, connect the
power cord and turn on the switch to resume operation.
(4) When the left power switch is powered on, you can use any of the methods described below to run the screen.
Note: when the screen is raised, make sure there is no obstacle and enough space on the top of the screen, and do not put your
head on the top of the screen to avoid personal injury and product failure.
The left side of the screen shell is equipped with a manual switch which can control the screen "up / stop / down".
Up
Stop
Down

17
2.Remote control——RF remote control / IR remote control
(1) Wireless RF remote control: when the screen is hidden and installed in the slot or requires remote control, wireless remote
control can be used. It can control the screen without aiming at the IR receiver.
(2) IR remote control needs to be connected with the IR receiver. When using IR remote control, make sure that the power switch
is turned on and aligned with the IR receiver head, so that the IR remote control can operate normally.(Unlike the wireless
remote control, the back of the infrared remote control is black, and there is an infrared signal lamp on the top)
IR receiver
Up
Stop
Down
When using, please aim
at the IR receiver
Front of remote control Perspective view of infrared
remote control
The remote have
infrared transmitter in here

18
For convenient access, the remote controller can be fixed on the wall surface and other planes through the bracket.(wall
screw or double-sided adhesive tape can be used for fixation)
outside of a wall
inside the wall

19
When the battery of the remote control needs to be replaced, as shown in the figure below, unscrew the cover of the remote
control with a small screw, then replace the new button battery, close the cover of the remote control, and tighten the screw to
prevent the loose battery from falling off;
Please place the battery face up and
push it in completely.
When the back cover is closed, please
jam the slot and push it down.
Push up
Take out the battery
load the battery
+
3V
CR2032
front up side
bottom
Push down