Celexon DELUXX SlimFrame SoundVision SFSV-177X99 User manual

Thank you for choosing a quality product from DELUXX. Please read
this manual carefully before assembly and keep for future reference.
User Manual
DELUXX Cinema Frame
Screen SlimFrame
DELUXX®, a brand of celexon Europe GmbH
[email protected] - Victory House, Chequers Road, Tharston, NR15 2YA

1
Hints
Read before construction and always follow the instructions.
Please check ALL parts for completeness and damage before assembly. If parts
are missing or damaged do not continue with the construction and contact the
supplier with whom you purchased the screen or contact DELUXX directly.
The screen may ONLY be constructed on soft, padded ground. The velor
or powder coating and especially the projection fabric could otherwise be
damaged.
Do not touch the fabric with your greasy hands.
The fabric must not be folded or kinked!
Please do not write or paint on the fabric.
No sharp objects must come into contact with the product, especially the fabric.
The projection surface must never be cleaned with cleaning agents (especially
nothing corrosive). Use mild (max 3%) soapy water.
The velor frame requires special care and should not be cleaned wet. A fine brush
or special nozzle on the vacuum cleaner may be used for cleaning.
The screen may only be installed horizontally and level.
The screen, especially the fabric must be kept away from fire and heat, otherwise
it can cause permanent damage.
Please note the front and back side of the fabric before installation.
Only install the screen on load-bearing masonry wall and only with enclosed
mounting brackets.
Build the screen with 2 people and install on the wall with 2 people.
Install the fabric with utmost care, it is very sensitive and kinking or folding
the fabric leads to permanent damage.
The product may not be installed by persons under 16 years or without the
presence of an adult.
Failure to comply with the above points may violate the product and warranty.
You may permanently damage or impair the functionality of the screen. DELUXX
assumes no responsibility if disregarded and the warranty will not stand.

3
In the box
2
Information:
6 parts are only included with larger screen sizes.
Aluminum velor cover (4x or 6x)
Aluminum frame parts (4x or 6x)
Tension rods for fabric
(4x or 6x)
Wall bracket
(2x or 3x)
Springs for fabric
tension
Tool for springs
Connector for inner and
outer frame (optional)
Frame reinforcement with
screws (optional)
Screws and Rawl plugs
for wall mounting
Screwdriver and
Allen Key
Corner connector incl. Screws for inner frame (4x)
Corner connector incl. Screws for outer velor cover
Projection Fabric (1x)

4
3
Step 1
Slide the corner connectors of the inner frame into the short frame pieces, then
slide them into the long frame pieces.
(If you have a 6 piece frame, prior to this step, use the connectors for the inner
frame pieces)
Before tightening the screws, make sure that the frame parts are as perfectly
aligned as possible with no gaps at the corners and at absolute right-angles. Once
you are happy, tighten the screws.
Step 2
Spread the fabric (face down) on a soft, clean and free of sharp objects) area and
carefully push the rods into the outer pockets of the fabric. Make sure that the front
of the fabric is pointing downwards.
Insert the tension rods carefully
otherwise the fabric can become
deformed or even be punctured.
Assembly of the screen

5
4
Step 3
Carefully place the previously secured inner frame with 2 people, centered as well
as possible on the projection fabric.
Start with one corner, using 4 springs, the fabric can be attached using the tension
rods and springs. Use the clamping aid and carefully pull the springs around the
frame and anchor the springs in the rear of the frame profile. The fabric is carefully
drawn around the frame. This must be done with 2 people, one person anchors
the fabric and a second person helps guide the fabric around the frame to avoid
damage/deformation of the fabric. Now repeat the process with the other corners.
When the 4 corners are connected: Start on the long sides in the middle and
anchor further springs working towards the edges. Then do the same (working
from the middle to the edges) on the shorter sides of the frame.
(Before doing this, If you have a six piece frame,screw the two frame reinforcements
to the long frame pieces on the rear of the frame.)
Step 4
Slide the outer (velor) frame pieces onto the screen and connect them with the
corner connectors in all 4 corners. Screw the inner and outer frame together. If you
hear a "click", the frame parts are sufficiently connected.
Caution: Be very careful when
attaching the fabric, do not rub or
scratch it on the frame. Carefully
connect the tension rods.
Assembly of the screen

6
5
Wall mounting
1. Depending on the width of your frame, bring the wall brackets to approximately
1/3 and 2/3 of the frame width on your wall. Use only load bearing masonry or solid
wood walls for mounting. The wall brackets must be absolutely level (use spirit level
and mark). Use only mounting material suitable for the wall material (eg dowels &
screws for concrete or wood screws for solid wood). Mount the bracket to the wall.
2. Carefully lift the frame with 2 people at a time and place it onto the previously
mounted wall brackets so that the upper frame profile attaches to the wall bracket.
It should slip in and anchor into place.
The installation of your screen is complete.
Assembly of the screen