Vivitek DU9800Z User manual

DU9800Z
User's ManualUser's Manual

DU9800Z DLP Projector - User Manual
UM9801017EN00
1
Table of Contents
Copyright ............................................................................................................................................................................... 3
Copyright........................................................................................................................................................................ 3
Disclaimer ...................................................................................................................................................................... 3
About the Manual ........................................................................................................................................................... 3
Important Safety Guidelines .................................................................................................................................................. 4
Safety Notification .......................................................................................................................................................... 4
Installation and Use Notices........................................................................................................................................... 6
Disposal of Old Electric and Electronic Equipment........................................................................................................ 6
Important Recycling Instructions.................................................................................................................................... 6
Introduction............................................................................................................................................................................ 7
Packing Checklist........................................................................................................................................................... 7
Projector Overview......................................................................................................................................................... 8
IO Panel ....................................................................................................................................................................... 10
Control Panel ............................................................................................................................................................... 11
Installation and Setting up ................................................................................................................................................... 14
Inserting or Changing the Remote Control Batteries ................................................................................................... 14
Installing the Projector.................................................................................................................................................. 15
Precautions for Installation ................................................................................................................................... 15
Mounting the Projector.......................................................................................................................................... 16
Installing or Removing the Optional Lens............................................................................................................. 17
Connecting to AC Power Supply.................................................................................................................................. 19
Turning On the Projector.............................................................................................................................................. 19
Turning Off the Projector.............................................................................................................................................. 20
Adjusting the Projection Mode ..................................................................................................................................... 21
Adjusting the Projected Image Position ....................................................................................................................... 22
Adjusting the Focus and Zoom .................................................................................................................................... 22
Adjusting Geometric Distortion .................................................................................................................................... 23
Keystone ............................................................................................................................................................... 23
Rotation................................................................................................................................................................. 24
Pincushion / Barrel................................................................................................................................................ 24
Arc......................................................................................................................................................................... 25
Corner Adjustment ................................................................................................................................................ 26
Preventing Unauthorized Use of the Projector ............................................................................................................ 28
Using the Control Panel Lock ............................................................................................................................... 28
Using the Security Lock ........................................................................................................................................ 29
Using Control ID for Multi-Projector Application........................................................................................................... 31
Using the Constant Brightness Function to Maintain the Brightness Output............................................................... 33
Connecting Equipment ........................................................................................................................................................ 34
Connecting a Computer ............................................................................................................................................... 34
Connecting a Video Device.......................................................................................................................................... 34
Connecting to a Control Equipment ............................................................................................................................. 35
Connecting a Screen Trigger ....................................................................................................................................... 36
Connecting an HDBaseT Transmitter .......................................................................................................................... 37
Using the Projector.............................................................................................................................................................. 38
Using On-Screen Display .................................................................................................................................................... 38
Using the On-Screen Display....................................................................................................................................... 38
Menu Tree .................................................................................................................................................................... 39
OSD Menu – INPUT..................................................................................................................................................... 43

DU9800Z DLP Projector - User Manual
UM9801017EN00
2
OSD Menu – PICTURE................................................................................................................................................ 46
OSG Menu – ALIGNMENT .......................................................................................................................................... 48
OSD Menu – CONTROL.............................................................................................................................................. 51
OSD Menu – SERVICE................................................................................................................................................ 54
Product Specification........................................................................................................................................................... 55
Supported Signal Input Timing ............................................................................................................................................ 56
Configurations of Terminals................................................................................................................................................. 59
DU9800Z Lens Series ......................................................................................................................................................... 60
Product Dimensions ............................................................................................................................................................ 61
LED Indication ..................................................................................................................................................................... 62
Common Problems and Solutions....................................................................................................................................... 63
About the Vivitek Support.................................................................................................................................................... 65

DU9800Z DLP Projector - User Manual
3
UM98001117EN00
Copyright
Copyright
The User's Manual (including all pictures, illustrations and software) is protected by the international copyright law. All
rights are reserved. No duplication of the manual or any content included in the manual is allowed without the written
consent of the manufacturer.
©2017 Vivitek. Vivitek is a trademark of Delta Electronics, Inc. ©All rights reserved. 2017
Disclaimer
The information in the manual is subject to change without notice. The manufacturer does not provide any statement or
warranty of the contents in the manual and clearly give up the implied warranties of merchantability and of fitness for a
particular purpose. The manufacturer reserves the rights to modify the publication and change the contents of the
materials at any time without notice to any person.
About the Manual
The manual describes how to install and use the projector and is applicable to the purchaser of this projector. Relevant
information (such as illustrations and descriptions) is put on the same page and accurate as much as possible the format,
easy for printing, is convenient for reading and paper-saving which is beneficial to environmental protection. It is
suggested to print only the page you need.

DU9800Z DLP Projector - User Manual
4
UM98001117EN00
Important Safety Guidelines
Thank you for purchasing this high quality product!
Read the Manual carefully to obtain the best performance. The Manual provides instructions on how to use the menu and
implement the operation.
Safety Notification
To turn off the main power, ensure to unplug from the power outlet.
To prevent electric shock, do not open the cabinet. There are high-voltage components inside.
Refer service to qualified service personnel.
The symbol warns the user about electric shock caused by voltage not insulated. Therefore, it is
dangerous to make any kind of contact with any parts inside the projector.
To prevent the projector from electrical discharge or electric shock, do not expose the projector to rain or
moist environment. Do not use the plug with an extension cord or an outlet unless all the prongs can be
fully inserted.
This symbol alerts the user that important information which should be read carefully to avoid problems
concerning the operation and maintenance of the projector.
WARNING TO CALIFORNIA RESIDENTS:
Handling the cables supplied with this equipment might expose user to a little lead, a chemical known to the Stage of
California, resulting in risks of barrenness. Please remember to wash hands after handling.
NOTIFICATION (CANADA)
This Class A digital equipment complies with Canadian ICES-003.
CE NOTIFICATION
This is a Class A product, which complies with rules for CE marking. This product may cause radio interference that the
user may be supposed to take adequate measures.
FCC NOTIFICATION
This device complies with part 15 of the FCC Rules. The operation is subject to the following two conditions:
(1) This device may not cause harmful interference;
(2) This device must accept any interference received, including interference that may cause undesired operation. This
equipment has been tested and found to comply with part 15 of the FCC Rules. These requirements are designed to
provide reasonable protection against harmful interference when the equipment operates in a commercial environment.
This equipment might generate radio frequency energy. If user does not install or use in accordance with the instructions
in manual, the radio frequency energy may interfere radio reception. If the above scenario occurs, the user may be
responsible for correcting the interference
WARNING!
Changes or modifications without approval from Vivitek could void the user’s authorization to operate
the product.
LIGHT MODULE

DU9800Z DLP Projector - User Manual
5
UM98001117EN00
A light module containing multiple laser diodes acts as the light source in the product.
These laser diodes are sealed in the light module. It is recommended to ask dealer for maintenance or repair services
of the light module.
The end user is not allowed to replace the light module.
Contact distributor who provides the qualified service for light module replacement and further information.
LASER SAFETY NOTIFICATION AND CAUTION
Do not stare at the lens while in use
CLASS 3R LASER PRODUCT
This Laser Product is designated as Class 3R during all procedures of operation.
LASER LIGHT - AVOID DIRECT EYE EXPOSURE.
Do not point laser or allow reflected laser light toward other people or reflective objects.
Direct or scattered light can be hazardous to eyes and skin.
There is a potential hazard of eye exposure to laser radiation if the included instructions are not followed.
Caution – use of controls, adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
Laser Parameters:
Wavelength : 450nm - 460nm Total internal power : >100W
Mode of operation : Pulsed, due to frame rate Apparent source size : >10mm, at lens stop
Pulse width : 0.93ms Divergence : >100 mili Radian
Maximum laser energy : 0.48mJ
Product Label
Manufacturer’s ID Label, Explanatory Label and Certification Statement Label
Hazard Warning Symbol and Aperture Label

DU9800Z DLP Projector - User Manual
6
UM98001117EN00
Installation and Use Notices
1. Read and keep this manual properly.
2. Pay attention to all the noted warnings, and follow all the guidelines and descriptions in this manual.
3. Do not use the projector near water.
4. Do not install the equipment near the thermal sources, such as heaters, radiators, furnace, amplifiers, and any other
equipment that may generate heat.
5. Be careful while holding the equipment or moving the trolley with projector to prevent the equipment from turning
over.
6. Notice whether there is any parts with flaws after receiving the projector.
7. Please notice that the projector will not power on until the lens is fitted. The protection covering the lens should be
taken to install the lens.
8. Do not let any vent be obstructed.
9. Do not destroy the safety protection function of polarized or grounding plug of the power cord. A polarized plug has
one wide and one narrow blade. The plug has two blades and one grounding blade. The wide blade or grounding
blade is provided for the safety concerns. If the plug provided does not match the outlet, please contact the
electrician to change outlet.
10. The +12V trigger only outputs 12V DC trigger signal. Do not connect other power input or output. Otherwise, the
equipment may malfunction.
11. Adjust the slide switch with suitable volt input, and then plug in the projector; the red LED indicator would flash and
then stabilize, getting into standby mode. User should only use the connectors or accessories provided by the
manufacturer.
12. When user turns on the projector, the red LED indicator would flash until stabilized. Do not look at the lens directly
while the projector is running.
13. Unplug the power cord of the equipment if there is a thunderstorm or the equipment is not going to be used for an
extended period of time.
14. It is suggested to properly keep the packaging materials for future transportation or afterservice.
15. If any breakdown occurs, please contact dealer or manufacture for qualified repair service.
Disposal of Old Electric and Electronic Equipment
The symbol on your product or the package represents that the product should not be treated as the normal household
waste when discarded but should be carried to the recycling location of the waste electric and electronic equipment. The
consequence on the environment and human health due to the incorrect disposal of the product can be prevented if it can
be ensured that the product is properly discarded. Material recycling is helpful to the protection of natural resources. The
symbol is only valid in the European Union. If you want to discard electrical and electronic equipment, contact the
governmental authorities or your dealer for the correct method of disposal.
Important Recycling Instructions
The product may contain other electronic wastes and may pose risk if not discarded properly. Abide by the local,
state/provincial or federal laws of recycling or discarding. For more information, please visit the website and contact
Electronic Industries Alliance (EIA) on WWW.EIAE.ORG.

DU9800Z DLP Projector - User Manual
7
UM98001117EN00
Introduction
The User's Manual describes the installation, setup and operation of the DU9800Z projector and provides assistance to
the installation personnel and the end-user to fully develop the performance of the projector. Vivitek has made every effort
to ensure that the information in the Manual is correct at the time of printing. The contents may be frequently updated due
to the continuous product improvements and customer feedback.
You can find the latest version of the Manual and the manual of other Vivitek products on www.vivitekcorp.com.
Packing Checklist
The following items are included in the packaging box of the DU9800Z series projector. If there is any loss or damage to
any item, contact your dealer or Vivitek customer service department.
ACPowerCordHDMI SignalCable WiredRemoteCable

IRRemoteControlBattery (AA,x2) DocumentationKit

RoHSCard(China)Certificate(China) 


DU9800Z DLP Projector - User Manual
8
UM98001117EN00
Projector Overview
Front-left View
Front-right View
Rear View
1. Front IR Receiver
The Receiver is for IR signals from the remote control.
2. LED Indicator
Display current projector status such as power, light source
status and warning.
3. Lens Mounting Hole
The mounting hole is for installing the projection lens.
4. Air Intake
The fan pulls the cool air to the projector for system cooling.
5. Control Panel
Press the button to operate the OSD menu or adjust the lens
Settings see OSD controls.
6. AC Power Switch
Turn on/off the AC power of the projector.
7. AC Inlet
Connect the supplied power cable to this inlet.
8. I/O Connector Panel
Connect to various input, control or output terminals to the
projector.
9. Lens Release Button
Press the Lens Release button before removing the lens.
10. Height Adjuster
Adjust level of projector
11. Intake Vent
The fans pull air to cool the radiator of the projector.
12. Rear IR Receiver
The Receiver is for IR signals from the remote control.
Important:
Air passes through the projector’s grill openings to ensure good air circulation and to keep the projector
running smoothly. Do not obstruct any of the grill openings and keep the required distance from any
object.

DU9800Z DLP Projector - User Manual
9
UM98001117EN00
Bottom View
13. Ceiling Mounting Hole
Total, six M6 screw holes with maximum depth
of 16mm
14. Recess for projector handling.
These four recesses can be used for handling the
projector.
Caution:
When installing, ensure that you use only UL Listed ceiling mounts. Contact your dealer for information
on mounting the projector on a ceiling.
With ceiling installation, use approved mounting hardware & M6 screws; maximum depth of screw is 16
mm.

DU9800Z DLP Projector - User Manual
10
UM98001117EN00
IO Panel
TRIGGER (12V +/-1.5V)
When connected to the screen through a 3.5mm cable,
the screen deploys automatically on startup of the
projector. The screen reacts when the projector is
powered off.
RS-232
The 9-pin D-sub interface is used to connect to the PC
control system and projector maintenance.
Component (V, H, B/Pb, G/Y, R/Pr)
Connect RGBHV or Component signal from computer or
component video enabled device
VGA
Provide the standard 15-pin VGA connection and can
connect to RGB, HD Component or personal computer.
MONITOR OUT
Connect to a monitor to display the projected content.
WIRED REMOTE
Connect the supplied remote controller to the projector
HDBaseT/LAN
Connect an Ethernet cable (Cat5/Cat6, not supplied)
from a computer, network device, or HDBaseT
transmitter.
HDMI 1
Connect the HDMI cable from a computer or video
device
DVI-D
Connect to DVI-D cable from a DVI-D output of the
device.
DisplayPort
Connect the DisplayPort cable from a computer or video
device.
SDI IN/OUT
Connect to SDI source.
HDMI 2
Connect the HDMI cable from a computer or video
device
3D SYNC IN / Out
Connect to the 3D IR synchronization signal transmitter.
Note for Trigger
When the projector is turned on, a control output signal (DC 12V) is delivered from this terminal.
Do not use this jack for anything other than intended use.
Note for Wired Remote
Please make sure whether the port for insertion is correct before the terminal of the wired remote
control is inserted. The remote control may be damaged if inserted to the wrong port such as trigger. Do
not use this jack for anything other than intended use.

DU9800Z DLP Projector - User Manual
11
UM98001117EN00
Control Panel
POWER
User the button to turn on/off the projector.
INPUT
Push the button to select the input signal. HDMI, DVI,
VGA, Component…etc.
AUTO SYNC
Implement automatic signal synchronization.
ASPECT
Change the aspect ratio of the current image and push
the button to change to the next aspect ratio settings.
MENU
Push the button to display or hide the OSD menu.
UP/Down/Left/Right
Use the button to select the OSD option.
ENTER
Use the button to select settings or confirm the changed
settings.
EXIT
Push the button to return to the menu on the previous
level or exit the OSD menu.
CENTER LENS
Push the button to center the lens and calibrate the
parameter of lens shift.
Note: The lens position needs to be calibrated for the
accurate lens shift operation after installing the lens.
Please center the lens every time after the lens is
mounted.
Blank
Use the button to stop the projection temporarily
LENS SHIFT
Use these four buttons to move the projected image to
the desired position.
FOCUS
Use the button to adjust the focus of the projected image.
ZOOM
Use the button to zoom in/out the projected image.

DU9800Z DLP Projector - User Manual
12
UM98001117EN00
Remote Control
On
Use the button to turn on the projector.
OFF
Use the button to turn off the projector.
FOCUS
Adjust the focus of the projected image.
ZOOM
Zoom in/out the projected image.
TEST PATTERN
Use the button to show the test pattern. Press this button again to switch to
the next pattern. Press the EXIT button to return to the projected image.
LENS SHIFT
Use the button to move the lens right or left.
ENTER
Use the button to select settings or confirm the changed settings.
MENU
Press the button to display or hide the OSD Menu.
EXIT
Press the button to return to the previous Menu or exit the OSD Menu.
AUTO PC
You can use this function to execute signal source auto synchronization
BLANK
Press the button to temporarily interrupt the projection.
STATUS
Show OSD MENU – SERVICE.
VGA
Select VGA as the input source.
COMPONENT
Select Component as input source.
ASPECT
Press the button to display aspect ratio options.
HDMI1
Select HDMI 1 as the input source.
HDMI2
Select HDMI 2 as the input source.
DVI
Select DVI-D as the input source.

DU9800Z DLP Projector - User Manual
13
UM98001117EN00
Wired Remote Jack
Connect to WIRED REMOTE terminal
on the projector
3G-SDI
Select 3G-SD as the input source.
DisplayPort
Select DisplayPort as input source.
HDBaseT
Select HDBaseT the input source.
CLEAR
Erase the set ID number of the remote control; refer to the section “Using
Control ID for Multi-projector Application”.
FREEZE
Freeze the projected image or resume the projection.
ID SET
Set up ID number for remote control; refer to the section “Using Control ID
for Multi-projector Application”.
Remote Control Operating Range
The remote control uses the infrared transmission to control the projector. It is not necessary to point the remote directly at
the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote
will function well within a radius of about 10 meters (25 feet) and 15 degrees above or below the projector level. If the
projector does not respond to the remote control, move a little closer.

DU9800Z DLP Projector - User Manual
14
UM98001117EN00
Installation and Setting up
Inserting or Changing the Remote Control Batteries
1. Remove the battery compartment cover by sliding the cover in the direction of the arrow.
2. Place two AA batteries with the correct polarity.
3. Replace and slide the cover as like the arrow in the illustration.
Important:
Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent
lights can disrupt remote control operation.
Be sure nothing obstructs the path between the remote control and the projector.
Do not expose the remote control to high temperature or humidity; otherwise, the remote control will not
function correctly.
Battery installation instructions
Make sure the battery is installed with the correct polarity.
Do not use the old and new batteries or the batteries of different types together.
Remove the battery if the remote control is not being used for long periods of time to prevent damage
caused by battery leakage.
1
2
3

DU9800Z DLP Projector - User Manual
15
UM98001117EN00
Installing the Projector
The high quality display effect can be guaranteed only when the projector is correctly installed. Generally, the light source
facing the screen should be reduced or eliminated as much as possible. The contrast of the image will be obviously
reduced if the light directly shines on the screen, such as the beam from windows or the searchlight cast on the image.
The image may become faded and not bright.
Precautions for Installation
Caution:
Projector installation must be done by a qualified professional. Contact your dealer for more information.
It is not recommended you install the projector yourself.
With ceiling installation, use approved mounting hardware & M6 screws; maximum depth of screw is 16
mm. Contact your dealer for information about mounting the projector on a ceiling.
Only use the projector on a solid and level surface. Serious injury and damage can occur if the projector
is dropped.
Caution:
Ensure that the hot air from the exhaust vent is not sucked into the projector.
Ensure the air intake and exhaust vents are unobstructed and keep the required distance from any
object. Below is required minimum distance between the vent and any object.
All added enclosures should pass a certified thermal evaluation to ensure that the projector does not
recycle exhaust air, as this may cause the projector to shut down even if the enclosure temperature is
with the acceptable operation temperature range.
Airflow and Heat Emission Minimum Distance to Vent
Caution:
Only use the projector on a solid and level surface. Serious injury and damage can occur if the projector is
dropped.
Please do not stack the projector on the surface of another projector. Serious injury and damage may
occur if the projector is dropped.

DU9800Z DLP Projector - User Manual
16
UM98001117EN00
Mounting the Projector
For mounting the projector, please use UL Listed ceiling mounts and M6 screws, maximum depth of screw is 16 mm.

DU9800Z DLP Projector - User Manual
17
UM98001117EN00
Installing or Removing the Optional Lens
Caution:
Do not shake or place excessive pressure on the projector or the lens components as the projector and
lens components contain precision parts.
When shipping the projector with the optional lens, remove the optional lens before shipping the
projector. The lens and the lens shift mechanism may encounter damage caused by improper handling
during transportation.
Before removing or installing the lens, be sure to turn off the projector and wait unitl the cooling fans
stop, and turn off the main power switch.
Do not touch the lens surface when removing or installing the lens.
Keep fingerprints, dust or oil off the lens surface. Do not scratch the lens surface.
Work on a level surface with a soft cloth under the projector to avoid scratchs or other damage.
If you remove and store the lens, attach the lens cap to the projector to keep out dust and dirt.
Install New Lens
1. If the Lens cover is installed, pull the edge of the lens cover with one hand ( ①), so that the lens cover can be
removed easily with the other hand ( ②)
2. Push the lens into the lens mounting hole (③) and turn it clockwise to the "Lock" position (④). When turning the lens,
the "Click" sound indicates that the lens is completely fixed and locked in place.
3. Check if the lens is fixed successfully by pulling the lens out of the holder gently.

DU9800Z DLP Projector - User Manual
18
UM98001117EN00
Removing the Existing Lens
1. Push the LENS RELEASE button all the way in and rotate the lens counterclockwise. The existing lens will be
disengaged
2. Pull out the existing lens slowly.
Important:
When installing the lens into the projector, be sure to remove the lens cap from the back of the optional
lens before installing the optional lens into the projector. Failure to do so will cause damage to the
projector and lens.
There is one safety switch inside the projector’s lens slot to prevent unexpected injury by laser beam.
The projector cannot be turned on if the projection lens has not been installed or is not installed
correctly. Please make sure the lens is installed properly before tuning on the projector.

DU9800Z DLP Projector - User Manual
19
UM98001117EN00
Connecting to AC Power Supply
The AC power cord is included in the box; plug the power cord to the AC socket on the IO panel.
Turning On the Projector
Once the projector is correctly located and the power cable and other connections are in place, it is important that the
projector is powered on correctly in order to avoid damage to components and un-necessary wear and tear. Refer to the
following guide to power on the projector.
1. Press the main power switch to the on ( I ) position as
shown. POWER LEDs will flash, then turn a solid red.
2. Press the POWER button on the control panel or ON
button on the remote control.
3. The Power LED and LIGHT LED flashes green until the
power on process is finished.
4. After a few seconds, both LEDs lights will become a
solid green to indicate the projector is ready for use.