Hitachi CP-AW3019WN User manual

1
Projector
CP-AW3019WN
User's Manual (detailed)
Operating Guide
Thank you for purchasing this projector.
►Before using this product, please read all manuals for this
product. Be sure to read “Safety Guide” rst. After reading them, store them in a
safe place for future reference.
WARNING
• The information in this manual is subject to change without notice.
• The illustrations in this manual are for illustrative purposes. They may differ
slightly from your projector.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
NOTE
Trademark acknowledgment
Various symbols are used in this manual. The meanings of these symbols are
described below.
About this manual
WARNING
CAUTION
This symbol indicates information that, if ignored, could possibly
result in personal injury or even death due to incorrect handling.
This symbol indicates information that, if ignored, could possibly
result in personal injury or physical damage due to incorrect
handling.
Please refer to the pages written following this symbol.

• Mac® is a registered trademark of Apple Inc.
• Windows®, DirectX®, DirectDraw® and Direct3D® are registered trademarks of Microsoft
Corporation in the U.S. and/or other countries.
• VESA and DDC are trademarks of the Video Electronics Standard Association.
•
HDMI, the HDMI logo, and High-Denition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United States and other countries.
• Trademark PJLink is a trademark applied for trademark rights in
Japan, the United States of America and other countries and areas.
• Blu-ray DiscTM and Blu-rayTM are trademarks of Blu-ray Disc Association.
•
StarBoard
®
is a registered trademark of Hitachi Solutions, Ltd. in Japan and other countries.
All other trademarks are the properties of their respective owners.
NOTICE This entry notices of fear of causing trouble.

2
Contents
Introduction ...............3
Features ......................3
Checking the contents of package ...3
Part names ....................4
Setting up .................7
Arrangement ...................7
Connecting with your devices
......9
Connecting to a power supply
.....15
Using the security bar and slot ....16
Using the cable cover ...........17
Remote control ............18
Installing the batteries ...........18
About the remote control signal ...18
Changing the frequency of remote control signal . . 19
Using as a simple PC mouse & keyboard . . 19
Interactive pen ...................20
Power on/off ..............21
Operating ................24
Adjusting the volume ............24
Temporarily muting the sound .....24
Selecting an input signal .........24
Searching an input signal ........26
Selecting an aspect ratio .........26
Adjusting the projector's elevator . . 27
Adjusting the zoom and focus .....27
Using the automatic adjustment feature ...28
Adjusting the position ...........29
Correcting the keystone distortions . . 29
Using the magnify feature ........30
Temporarily freezing the screen ...31
Temporarily blanking the screen . . 31
Using the menu function ........32
EASY MENU. . . . . . . . . . . . . . . 34
InteractIve, aspect, D-zoom,
Keystone,
Keystone, perfect fIt
,
pIcture moDe,
eco moDe, InstallatIon, reset, fIlter tIme,
language, aDvanceD menu, exIt
INTERACTIVE menu ........36
PICTURE menu ............37
BrIghtness, contrast, gamma, color temp,
color, tInt, sharpness, actIve IrIs, mymemory
IMAGE menu ..............40
aspect, over scan, v posItIon, h posItIon,
h phase, h sIze, auto aDjust execute
INPUT menu ..............43
progressIve, vIDeo nr, color space,
vIDeo format, hDmI format, hDmI range,
computer In, frame locK, resolutIon

SETUP menu ..............47
D-zoom, D-shIft, pIct.posIt.h,
Keystone,
Keystone, perfect fIt
,
auto eco moDe, eco moDe, InstallatIon
,
stanDBy moDe, monItor out
AUDIO menu ..............53
volume, speaKer, auDIo source,
mIc level, mIc volume
SCREEN menu.............55
language, menu posItIon, BlanK,
auto BlanK, start up,
MyScreen,
MyScreen Lock
, message, source name,
template, c.c.
OPTION menu .............61
auto search, DIrect power on,
auto power off, usB type B, lamp tIme,
fIlter tIme, myButton, mysource,
servIce
NETWORK menu ...........74
wIreless setup, wIreless InformatIon,
wIreD setup, wIreD InformatIon,
projector name, myImage, amx D.D.,
presentatIon, servIce
SECURITY menu ...........86
securIty passworD change,
MyScreen
passworD, pIn locK,
transItIon Detector, mytext passworD,
mytext DIsplay, mytext wrItIng,
clonIng locK
Presentation tools .........92
Interactive Function ..............92
PC-LESS Presentation ..........100
USB Display (Windows computer) . . 110
USB Display (Mac computer)
......
115
Maintenance .............119
Replacing the lamp ............ 119
Cleaning and replacing the air lter . 121
Caring for the mirror and lens
......123
Other care ...................124
Troubleshooting ..........126
Related messages ............126
Regarding the indicator lamps ...128
Resetting all settings ...........131
Phenomena that may be easy to
be mistaken for machine defects . . 131
Specications ............142


3
Introduction
• Keep the original packing materials, for future reshipment. Be sure
to use the original packing materials when moving the projector. Use special
caution for the lens.
NOTE
Introduction
The projector provides you with the broad use by the following features.
Checking the contents of package
ü The unique lens and mirror system realizes ultra short distance
projection,which gives you more various way of use.
ü The motorized lens door offers you very simple use of the projector.
ü
The double layer lter system is expected to function longer and offers you
less maintenance frequency.
ü The HDMI port can support various image equipment which have digital
interface to get clearer pictures on a screen.
ü This projector can be controlled and monitored via LAN connection.
Furthermore, you can use the designated USB wireless adapter (optional) to
establish wireless LAN connection.
ü This projector's network supports the PJLinkTM standard.
ü The Interactive Pen included with the projector allows you to write or
draw directly on the projected image. Also, you can control the connected
computer on the screen in the same way as using a mouse.
Please see the Contents of package section in the User’s Manual (concise)
which is a book. Your projector should come with the items shown there. Require
of your dealer immediately if any items are missing.
Features

4
Introduction
(1) Lamp cover (119)
The lamp unit is inside.
(2) Control panel (5)
(3) Elevator feet (x 2) (27)
(4) Remote sensor (18)
(5) Lens (123)
(6) Intake vents
(7) Filter cover (121)
The air lter and intake vent
are inside.
(8) Speaker (12, 24, 53)
(9) Exhaust vent
(10) AC IN(AC inlet) (15)
(11) Ports (5)
(12) Security bar (16)
(13) Security slot (16)
(14) Lens door (123)
(15) Mirror (123)
(16) Spacer (Small) (27)
(17) Spacer (Large) (27)
(18) PEN sensor (124)
►HOT! : Do not touch around the lamp cover and the exhaust
vents during use or just after use, since it is too hot.
►Be careful not to pinch your nger with the lens door, to prevent an injury.
►Never look into the projection lens or mirror while the projection lamp lights,
since the projection lamp ray may cause a trouble on your eyes.
►Do not use the security bar and slot to prevent the projector from falling down,
since it is not designed for it.
WARNING
►Maintain normal ventilation to prevent the projector from
heating up. Do not cover, block or plug up the vents. Do not place anything that
can stick or be sucked to the vents, around the intake vents. Clean the air lter
periodically.
CAUTION
Part names
Projector
(5) (14)
(15)
(18)
(4)
(10)
HOT!
HOT!
(1) (2)
(6)
(3)
(7)
(8)
(11)
(12)
(13)
(9)
(16)
(17)
Small
Large

5
Introduction
Part names (continued)
Control panel
(1) STANDBY/ON button (21)
(2) INPUT button (24)
(3) POWER indicator (21, 128)
(4) TEMP indicator (128)
(5) LAMP indicator (128)
Buttons ◄/►/▲/▼
(6) FOCUS +/- buttons
when no menu is displayed (28), or
Cursor ◄/► buttons
when a menu is displayed (32). FOCUS +/- function is invalid when the
USB TYPE A port is selected as the input source.
(7) MENU buttons
when no menu is displayed (32), or
Cursor ▲/▼ buttons
when a menu is displayed (32).
The ◄/►/▲/▼ buttons on the projector work only as the cursor buttons while the
template is displayed (59).
Ports (9 ~ 14)
(1) USB TYPE A port (x2)
(2) LAN port
(3) HDMI port
(4) USB TYPE B port
(5) MIC port
(6) AUDIO IN1 port
(7) AUDIO IN2 port
(8) AUDIO IN3(L,R) ports
(9) AUDIO OUT (L,R) ports
(10) COMPUTER IN1 port
(11) COMPUTER IN2 port
(12) MONITOR OUT port
(13) CONTROL port
(14) VIDEO port
(15) S-VIDEO port
(7)
(3) (11)
(6) (12)
(10)
(8)
(14)
(4)
(1)
(13)
(15)
(2)
(5)
(9)
(1)
(7) (2)
(3)
(5)
(4) (6)

6
Introduction
Remote control
(1) VIDEO button (25)
(2) COMPUTER button (25)
(3) SEARCH button (26)
(4) STANDBY/ON button (21)
(5) ASPECT button (26)
(6) AUTO button (28)
(7) BLANK button (31)
(8) MAGNIFY - ON button (30)
(9) MAGNIFY - OFF button (30)
(10) MY SOURCE/DOC.CAMERA button (25, 65)
(11) VOLUME - button (24)
(12) PAGE UP button (19)
(13) PAGE DOWN button (19)
(14) VOLUME + button (24)
(15) MUTE button (24)
(16) FREEZE button (31)
(17) MY BUTTON - 1 button (64)
(18) MY BUTTON - 2 button (64)
(19) KEYSTONE button (29)
(20) FOCUS - button (28)
(21) FOCUS + button (28)
(22) D-ZOOM - button (27)
(23) D-ZOOM + button (27)
(24) POSITION button (29, 33)
(25) MENU button (32, 33)
(26) ▲/▼/◄/► cursor buttons (32)
(27) ENTER button (32, 33)
(28) ESC button (32)
(29) RESET button (32)
(30) Battery cover (18)
Interactive pen
(1) Pen tip (20)
(2) SIDE BUTTON No.0 button (98)
(3) SIDE BUTTON No.1 button (98)
(4) Battery cover (20)
(1)
(2)
(3)
(4)
• Interactive Pen is henceforth denoted as
“pen”.
NOTE
Back of
the remote control
(30)
VIDEO
DOC.CAMERA
KEYSTONE
ASPECT SEARCH BLANK
MUTE
MY BUTTON
POSITION
ESC
MENU
RESET
COMPUTER MY SOURCE/
AUTO
MAGNIFY PAGE
DOWN
ON
OFF
FREEZE UP
ー
＋
VOLUME
12
ENTER
FOCUS
-+
D-ZOOM
-+
(2)
(1)
(6)
(5)
(16)
(8)
(9)
(19)
(17)
(20)
(21)
(24)
(26)
(28)
(10)
(4)
(3)
(7)
(12)
(14)
(11)
(13)
(15)
(18)
(23)
(22)
(25)
(27)
(29)

7
Arrangement
Refer to table T-1 and gures F-1 and F-2 at the end of User's Manual (concise) to determine
the screen size and projection distance.
The values shown in the table are calculated for a full size screen: 1280 x 800
a Screen size (diagonal) b1 , b2 Projection distance (±8%) c1 , c2 Screen height (±8%)
Setting up
Install the projector according to the environment and manner the projector will be
used in.
Setting up
(continued on next page)
• For the case of installation in special conditions such as on the wall or ceiling, the
specied mounting accessories and service may be required. Tabletop use must be
setup with the designated optional accessories. Before installing the projector, consult
your dealer about your installation.
•
The screen position may shift after installation if the projector is mounted on locations
such as the wall or ceiling, due to the exibility of the plastic projector body. If readjustment
is necessary, consult with your dealer or service personnel.
• The projected image position and/or focus may change during warm-up (approx. 30
minutes after the lamp is turned on) or when the ambient conditions change. Readjust
the image position and/or focus as necessary.
• Since the projector features an ultra short throw, be aware that it is required to select a
screen carefully to have better performance.
- A soft screen such as a pull-down screen may cause serious distortion of a projected
image. A hard screen such as a board screen is recommended for use with this
projector.
- A high-gain screen such as a bead screen that has narrow viewing angle is not suitable
for this projector. A low-gain screen (around 1.0) such as a matte screen that has wide
viewing angle is recommended for use with this projector.
- A screen with a weave pattern may cause moiré on the projected image, which is not
a failure of the projector. A screen that has less moiré effects is recommended for use
with this projector.
► Place the projector in a stable horizontal position. If the
projector falls or is knocked over, it could cause injury and/or damage to the
projector. Using a damaged projector could then result in re and/or electric shock.
• Do not place the projector on an unstable, slanted or vibrational surface such
as a wobbly or inclined stand.
• Do not place the projector on its side or front position. To place the projector
on its rear position for the table top use, it is required to use the designated
optional parts. Consult with your dealer.
• Consult with your dealer before a special installation such as on the wall or ceiling.
WARNING

8
Setting up
Arrangement (continued)
(continued on next page)
►Place the projector in a cool place, and ensure that there is
sufcient ventilation. The high temperature of the projector could cause re,
burns and/or malfunction of the projector.
• Do not stop-up, block or otherwise cover the projector's vents.
• Keep a space of 30 cm or more between the sides of the projector and other
objects such as walls.
• Do not place or attach anything that would block the lens or vent holes.
• Do not place the projector on metallic thing or anything weak in heat.
• Do not place the projector on carpet, cushions or bedding.
• Do not place the projector in direct sunlight or near hot objects such as heaters.
Do not place the projector where the air from an air conditioner or similar unit
will blow on it directly.
•
Do not place anything near the projector lens or vents, or on top of the projector.
• Do not place anything that may be sucked into or stick to the vents on the
bottom of the projector. This projector has some intake vents also on the bottom.
►Do not place the projector anyplace where it may get wet. Getting the projector
wet or inserting liquid into the projector could cause re, electric shock and/or
malfunction of the projector.
• Do not place the projector in a bathroom or the outdoors.
• Do not place anything containing liquid near the projector.
• Do not place the projector where any oils, such as cooking or machine oil, are used.
► Use only the mounting accessories the manufacturer specied, and leave installing
and removing the projector with the mounting accessories to the service personnel.
• Read and keep the user’s manual of the mounting accessories used.
WARNING
►Avoid placing the projector in smoky, humid or dusty place.
Placing the projector in such places could cause re, electric shock and/or
malfunction of the projector.
• Do not place the projector near humidiers, smoking spaces or a kitchen. Also
do not use an ultrasonic humidier near the projector. Otherwise chlorine and
minerals contained in tap water are atomized and could be deposited in the
projector causing image degradation or other problems.
► Position the projector to prevent light from directly hitting the projector's remote sensor.
►Do not place the product in a place where radio interference may be caused.
►Do not place this product in a magnetic eld.
► If the projector is used at an altitude of about 1600 m or higher, set ALTITUDE
of the SERVICE item in the OPTION menu to HIGH (66). Otherwise, set it to
NORMAL.
If the projector is used with a wrong setting, it may cause damage to the projector
itself or the parts inside.
CAUTION

9
Setting up
Before connecting the projector to a device, consult the manual of the device to
conrm that the device is suitable for connecting with this projector and prepare
the required accessories, such as a cable in accord with the signal of the device.
Consult your dealer when the required accessory did not come with the product or
the accessory is damaged.
After making sure that the device and projector are turned off, connect them
following the instructions below.
► Use only the appropriate accessories. Otherwise it could cause
a re or damage to the device and the projector.
- Use only the accessories specified or recommended by the projector’s
manufacturer. Consult your dealer when the required accessory did not come
with the product or the accessory is damaged. It may be regulated under some
standard.
- For a cable with a core at only one end, connect the end with the core to the
projector. That may be required by EMI regulations.
- Neither disassemble nor modify the projector and the accessories.
- Do not use the damaged accessory. Be careful not to damage the accessories.
Route a cable so that it is neither stepped on nor pinched out.
WARNING
►Do not turn on or off the projector while connected to a device
in operation, unless that is directed in the manual of the device. Otherwise it may
cause malfunction in the device or projector.
►Be careful not to mistakenly connect a connector to a wrong port. Otherwise it
may cause malfunction in the device or projector.
- When connecting a connector to a port, make sure that the shape of the
connector ts the port.
- Tighten the screws to connect a connector equipped with screws to a port.
- Use the cables with straight plugs, not L-shaped ones, as the input ports of the
projector are recessed.
CAUTION
Connecting with your devices
(continued on next page)
Arrangement (continued)
• The projector may make a rattling sound when tilted, moved or
shaken, since a ap to control the air ow inside of the projector has moved. Be
aware that this is not a failure or malfunction.
• The incoming light to the screen from the projector has a large angle. While
the white image is on the screen, you may see it with colors, but this is because
of the type of the screen used or the angles viewed, and it is not a malfunction.
• When the ambient temperature is around 35 to 40°C, the brightness of lamp
is reduced automatically.
NOTE

10
(continued on next page)
VCR/DVD/Blu-ray Disc
player
Computer
COMPONENT
Cb/Pb
Y
Cr/Pr
HDMI
RL
VIDEO
S-VIDEO
AUDIO
OUT
AUDIO
OUT
USB
(A) DISPLAY RS-232C
HDMI
LAN
Connecting with your devices (continued)
• When AUTO is selected for the COMPUTER IN1 or COMPUTER IN2 port in
COMPUTER IN of the INPUT menu, that port will accept component video
signals (45).
• When the USB TYPE B port and the computer's USB type A port are connected,
you can use the USB TYPE B port as a picture input port from the computer, use
the remote control as a simple mouse and keyboard of the computer, or use the
Interactive Function (19, 62).
Setting up
• Plug-and-Play is a system composed of a computer, its operating system
and peripheral equipment (i.e. display devices). This projector is VESA DDC
2B compatible. Plug-and-Play can be used by connecting this projector to a
computer that is VESA DDC (display data channel) compatible.
- Take advantage of this feature by connecting a computer cable to the
COMPUTER IN1 port (DDC 2B compatible). Plug-and-Play may not work
properly if any other type of connection is attempted.
- Please use the standard drivers in your computer as this projector is a Plug-and-
Play monitor.
About Plug-and-Play capability
Access point